aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata/sata_inic162x.c
AgeCommit message (Collapse)Author
2007-08-31[libata] Bump driver versionsJeff Garzik
Bump the versions for drivers that were modified, but had not already had a version number bump. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: make ->scr_read/write callbacks return error codeTejun Heo
Convert ->scr_read/write callbacks to return error code to better indicate failure. This will help handling of SCR_NOTIFICATION. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09[libata] Use ATA_UDMAx standard masks when filling driver's udma_mask infoJeff Garzik
The ATA_UDMAx masks are self-documenting, and far better than manually writing in the hex mask. Note that pata_it8213 mask differed from the comment. Added a FIXME there. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09[libata] drivers: remove 'void __iomem *' casts from pre-iomap daysJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-02sata_inic162x: disable LBA48 devicesTejun Heo
sata_inic162x can't do LBA48 properly yet and is likely to corrupt data on drives larger than LBA28 limit. Disable LBA48 devices during device configuration. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-21libata: bump versionsJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11libata: reimplement suspend/resume support using sdev->manage_start_stopTejun Heo
Reimplement suspend/resume support using sdev->manage_start_stop. * Device suspend/resume is now SCSI layer's responsibility and the code is simplified a lot. * DPM is dropped. This also simplifies code a lot. Suspend/resume status is port-wide now. * ata_scsi_device_suspend/resume() and ata_dev_ready() removed. * Resume now has to wait for disk to spin up before proceeding. I couldn't find easy way out as libata is in EH waiting for the disk to be ready and sd is waiting for EH to complete to issue START_STOP. * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config(). This fixes spindown on shutdown and suspend-to-disk. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-01libata: improve 0xff status handlingTejun Heo
For PATA, 0xff status indicates empty port. For SATA, it depends on how the controller emulates status register. On some controllers, 0xff is used to represent broken link or certain stage during reset. libata currently deals SATA the same. This hasn't caused any problem because problematic situations usually only occur after hotplug or other link disruption events and libata blindly waited for the device to spin up and settle after hotplug giving the link and device whatever time to go through those stages. libata is going to replace unconditional spinup wait with generic timed sequence of resets, so not only getting 0xff handling right for SATA is, well, the right thing to do, it's much more important now. This patch makes the following changes. * Make ata_bus_softreset() return -ENODEV if any of its wait fails due to 0xff status. * Fail soft/hardreset if status wait returns -ENODEV indicating 0xff status while SStatus says the link is online. e.g. Reset fails if status is 0xff after reset when SStatus reports the linke is online. If SCR registers are not available, everything is the same as before. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-01libata: add deadline support to prereset and reset methodsTejun Heo
Add @deadline to prereset and reset methods and make them honor it. ata_wait_ready() which directly takes @deadline is implemented to be used as the wait function. This patch is in preparation for EH timing improvements. * ata_wait_ready() never does busy sleep. It's only used from EH and no wait in EH is that urgent. This function also prints 'be patient' message automatically after 5 secs of waiting if more than 3 secs is remaining till deadline. * ata_bus_post_reset() now fails with error code if any of its wait fails. This is important because earlier reset tries will have shorter timeout than the spec requires. If a device fails to respond before the short timeout, reset should be retried with longer timeout rather than silently ignoring the device. There are three behavior differences. 1. Timeout is applied to both devices at once, not separately. This is more consistent with what the spec says. 2. When a device passes devchk but fails to become ready before deadline. Previouly, post_reset would just succeed and let device classification remove the device. New code fails the reset thus causing reset retry. After a few times, EH will give up disabling the port. 3. When slave device passes devchk but fails to become accessible (TF-wise) after reset. Original code disables dev1 after 30s timeout and continues as if the device doesn't exist, while the patched code fails reset. When this happens, new code fails reset on whole port rather than proceeding with only the primary device. If the failing device is suffering transient problems, new code retries reset which is a better behavior. If the failing device is actually broken, the net effect is identical to it, but not to the other device sharing the channel. In the previous code, reset would have succeeded after 30s thus detecting the working one. In the new code, reset fails and whole port gets disabled. IMO, it's a pathological case anyway (broken device sharing bus with working one) and doesn't really matter. * ata_bus_softreset() is changed to return error code from ata_bus_post_reset(). It used to return 0 unconditionally. * Spin up waiting is to be removed and not converted to honor deadline. * To be on the safe side, deadline is set to 40s for the time being. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28libata: convert the remaining SATA drivers to new init modelTejun Heo
Convert ahci, sata_sil, sata_sil24, sata_svw, sata_qstor, sata_mv, sata_sx4, sata_vsc and sata_inic162x to new init model. Now that host and ap are available during intialization, functions are converted to take either host or ap instead of low level parameters which were inevitable for functions shared between init and other paths. This simplifies code quite a bit. * init_one()'s now follow more consistent init order * ahci_setup_port() and ahci_host_init() collapsed into ahci_init_one() for init order consistency * sata_vsc uses port_info instead of setting fields manually * in sata_svw, k2_board_info converted to port_info (info is now in port flags). port number is honored now. Tested on ICH7/8 AHCI, jmb360, sil3112, 3114, 3124 and 3132. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28libata: improve AC_ERR_DEV handling for ->post_internal_cmdTejun Heo
->post_internal_cmd is simplified EH for internal commands. Its primary mission is to stop the controller such that no rogue memory access or other activities occur after the internal command is released. It may provide error diagnostics by setting qc->err_mask but this hasn't been a requirement. To ignore SETXFER failure for CFA devices, libata needs to know whether a command was failed by the device or for any other reason. ie. internal command needs to get AC_ERR_DEV right. This patch makes the following changes to AC_ERR_DEV handling and ->post_internal_cmd semantics to accomodate this need and simplify callback implementation. 1. As long as the correct bits in the result TF registers are set, there is no need to set AC_ERR_DEV explicitly. libata EH core takes care of that for both normal and internal commands. 2. The only requirement for ->post_internal_cmd() is to put the controller into quiescent state. It needs not to set any err_mask. 3. ata_exec_internal_sg() performs minimal error analysis such that AC_ERR_DEV is automatically set as long as result_tf is filled correctly. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28libata: handle ata_pci_device_do_resume() failure while resumingDmitriy Monakhov
Since commit:553c4aa630af7bc885e056d0436e4eb7f238579b ata_pci_device_do_resume() can return error code, all callers was updated except this one. Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28libata: dev_config does not need ap and adev passingAlan
It used to be impossible to get from ata_device to ata_port but that is no longer true. Various methods have been cleaned up over time but dev_config still takes both and most users don't need both anyway. Tidy this one up Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-19sata_inic162x: kill double region requestsTejun Heo
Regions are requested twice during initialization causing the second one to fail. This is regression introduced during iomap conversion. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-02libata: add missing CONFIG_PM in LLDsTejun Heo
Add missing #ifdef CONFIG_PM conditionals around all PM related parts in libata LLDs. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-14[PATCH] scheduled removal of SA_XXX interrupt flags: ata fixAndrew Morton
SA_SHIRQ is going away. Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-09sata_inic162x: fix a few glitches in hardresetTejun Heo
* Hardreset must not exit without actually performing reset regardless of link status. We're resetting the link after all. * Minor message update. * 150ms delay is meaningful iff link is online after reset is complete. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: add another IRQ calls (libata drivers)Akira Iguchi
This patch is against each libata driver. Two IRQ calls are added in ata_port_operations. - irq_on() is used to enable interrupts. - irq_ack() is used to acknowledge a device interrupt. In most drivers, ata_irq_on() and ata_irq_ack() are used for irq_on and irq_ack respectively. In some drivers (ex: ahci, sata_sil24) which cannot use them as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: convert to iomapTejun Heo
Convert libata core layer and LLDs to use iomap. * managed iomap is used. Pointer to pcim_iomap_table() is cached at host->iomap and used through out LLDs. This basically replaces host->mmio_base. * if possible, pcim_iomap_regions() is used Most iomap operation conversions are taken from Jeff Garzik <jgarzik@pobox.com>'s iomap branch. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: update libata LLDs to use devresTejun Heo
Update libata LLDs to use devres. Core layer is already converted to support managed LLDs. This patch simplifies initialization and fixes many resource related bugs in init failure and detach path. For example, all converted drivers now handle ata_device_add() failure gracefully without excessive resource rollback code. As most resources are released automatically on driver detach, many drivers don't need or can do with much simpler ->{port|host}_stop(). In general, stop callbacks are need iff port or host needs to be given commands to shut it down. Note that freezing is enough in many cases and ports are automatically frozen before being detached. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09sata_inic162x: finally, driver for initio 162x SATA controllers, take #2Tejun Heo
Driver for Initio 162x SATA controllers. ATA r/w, ATAPI r, hotplug and suspend/resume work. ATAPI w (recording, that is) broken. Feel free to fix it, but be warned, this controller is weird. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>