| Age | Commit message (Collapse) | Author |
|---|
|
Commit 721449bf0d51213fe3abf0ac3e3561ef9ea7827a added support for using the
ADMA notifier bits to determine which commands to check for completion.
However there have been reports that this causes command timeouts in certain
cases. This is still being investigated. In addition, apparently the notifiers
won't work if ADMA is disabled on the other port as a result of an ATAPI device
being connected, and we don't handle this case properly.
For now, just restore the previous behavior of checking all active commands
to see if they are complete, without relying on the notifiers.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
No code changes.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Recently Tejun wrote a patch to ahci.c to make it raise a HSM violation
if the drive attempted to complete a tag that wasn't outstanding. We could
run into the same problem with sata_nv ADMA. This adds code to raise a HSM
violation error if the controller gives us a notifier tag that isn't
outstanding, since the drive may be issuing spurious completions.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sata_nv implemented its own copies of the BMDMA helper functions for ADMA,
since the ADMA BMDMA status registers are PIO while the other registers
are MMIO, and this was the only way to handle this previously. Now that
we have iomap support, the standard routines should just work, so use them.
The only thing we need to override as far as ADMA and BMDMA is the
post_internal_cmd callback, where we should only call ata_post_internal_cmd
if we are in port-register mode.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
We already have code that handles hotplug interrupt indications in ADMA
mode, this turns on the control flag that actually enables these interrupts.
Also fixes some cases in the same functions where a 16-bit register was read
using a readl instead of a readw.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The hardware provides us a notifier register that indicates what command
tags have completed. Use this to determine which CPBs to check, rather
than blindly checking all active CPBs. This should provide a minor
performance win, since if the controller has touched some of these
incomplete CPBs, accessing them will likely result in a cache miss.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This edits the taskfile setup to more closely match the way that libata
sends the taskfile for other controllers. This avoids putting taskfile writes
into the CPB buffer that are not needed according to the taskfile flags.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Clean up the initialization of the CPB and APRD structures so that we
strictly follow the rules for ordering of writes to the CPB flags and
response flags, and prevent duplicate initialization.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When error handling occurs with pending commands, output the contents
of the next CPB count and next CPB index registers as well as the others,
since these may be useful for debugging.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch appears to solve some problems with commands timing out in
cases where an NCQ command is immediately followed by a non-NCQ command
(or possibly vice versa). This is a rather ugly solution, but until we
know more about why this is needed, this is about all we can do.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some debug output in the ADMA error_handler function was removed recently,
but it may be useful in certain cases, like NCQ commands timing out. Add it
back in, but make it a bit more intelligent so that it only prints if
command(s) are active and only prints the CPBs for those commands.
That way it won't spew at inappropriate times like suspend/resume.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ADMA-capable controllers provide a bit in the status register that appears
to indicate that the controller detected an SError condition. Update sata_nv
to detect this and trigger error handling in order to handle the fault.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ata_pci_device_do_resume can fail if the PCI device couldn't be re-enabled.
Update sata_nv to propagate the return value from this call and to not try
to do any other resume activities if it fails. Fixes a compile warning.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update sata_nv to wait for the controller to indicate via the status
register that it has entered the requested state when switching between
ADMA mode and register mode. This issue came up recently when debugging
some problems with cache flush command timeouts and while it didn't appear
to fix that problem, this is something we should likely be doing in any
case.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some problems showed up recently with cache flush commands timing out on
sata_nv. Previously these commands were always handled by transitioning to
legacy mode from ADMA mode first. The timeout problem was worked around
already by a change to the interrupt handling code for legacy mode, but for
non-data commands like these it appears we can handle them in ADMA mode, so
the switch to legacy mode is not needed.
This patch changes the behavior so that we use ADMA mode to submit
interrupt-driven commands with ATA_PROT_NODATA protocol. In addition to
avoiding the problem mentioned above entirely, this avoids the overhead of
switching to legacy mode and back to ADMA mode for handling cache flushes.
When handling non-DMA-mapped commands, we leave the APRD blank and clear
the NV_CPB_CTL_APRD_VALID field in the CPB so the controller does not
attempt to read it.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This cleans up a few issues with the error handling in sata_nv in ADMA mode
to make it more consistent with other NCQ-capable drivers like ahci and
sata_sil24:
- When a command failed, we would effectively set AC_ERR_DEV on the
queued command always. In the case of NCQ commands this prevents libata
from doing a log page query to determine the details of the failed
command, since it thinks we've already analyzed. Just set flags in the
port ehi->err_mask, then freeze or abort and let libata figure out what
went wrong.
- The code handled NV_ADMA_STAT_CPBERR as a "really bad error" which
caused it to set error flags on every queued command. I don't know
exactly what this flag means (no docs, grr!) but from what I can guess
from the standard ADMA spec, it just means that one or more of the CPBs
had an error, so we just need to go through and do our normal checks in
this case.
- In the error_handler function the code would always dump the state of
all the CPBs. This output seems redundant at this point since libata
already dumps the state of all active commands on errors (and it also
triggers at times when it shouldn't, like when suspending). Take this
out.
[akpm@osdl.org: many coding-style fixes]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Allen Martin <AMartin@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch is against each libata driver.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.
In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.
In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.
* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update libata LLDs to use devres. Core layer is already converted to
support managed LLDs. This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path. For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.
As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down. Note that freezing is enough in many cases
and ports are automatically frozen before being detached.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Thoughts from Jeff & company on merging the patch below into libata-dev?
This has been in the -mm tree for over a month now, I haven't heard any
complaints about regressions..
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Most of these contributed by that mysterious figger known as A.C.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Several people reported issues with certain drive commands timing out on
sata_nv controllers running in ADMA mode. The commands in question were
non-DMA-mapped commands, usually FLUSH CACHE or FLUSH CACHE EXT.
From experimentation it appears that the NV_INT_DEV indication isn't
always set when a legitimate command completion interrupt is received on
a legacy-mode command, at least not on these controllers in ADMA mode.
When a command is pending on the port, force the flag on always in the
irq_stat value before calling nv_host_intr so that the drive busy state
is always checked by ata_host_intr.
This also fixes some questionable code in nv_host_intr which called
ata_check_status when a command was pending and ata_host_intr returned
"unhandled". If the device interrupted at just the wrong time this could
cause interrupts to be lost.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The content of memory map io of BAR5 have been change from MCP65 then
sata_nv can't work fine on the platform based on MCP65 and MCP67, so move
their IDs from sata_nv.c to ahci.c.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
The attached patch against 2.6.19-rc6-mm1 fixes some problems in sata_nv
with ATAPI devices on controllers running in ADMA mode. Some of the
logic in the nv_adma_bmdma_* functions was inverted causing a bunch of
warnings and caused those functions not to work properly. Also, when an
ATAPI device is connected, we need to use the legacy DMA engine. The
code now disables the PCI configuration register bits for ADMA so that
this works, and ensures that no ATAPI DMA commands go through until this
is done.
Fixes Bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=7538
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
NV controllers sometimes fail to perform softreset after hotplug.
Make it use hardreset to resume link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds support for ADMA mode on NVIDIA nForce4 (CK804/MCP04) SATA
controllers to the sata_nv driver. Benefits of ADMA mode include:
- NCQ support
- Reduced CPU overhead (controller DMAs command information from memory
instead of them being pushed in by the CPU)
- Full 64-bit DMA support
ADMA mode is enabled by default in this version. To disable it, set the
module parameter adma_enabled=0.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
|
|
* Use PCI_VDEVICE() macro
* const-ify pci_device_id table
* standardize list terminator as "{ }"
* convert spaces to tab in pci_driver struct (Alan-ism)
* various minor whitespace cleanups
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Noticed by several people.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The biggest change is that ata_host_set is renamed to ata_host.
* ata_host_set => ata_host
* ata_probe_ent->host_flags => ata_probe_ent->port_flags
* ata_probe_ent->host_set_flags => ata_probe_ent->_host_flags
* ata_host_stats => ata_port_stats
* ata_port->host => ata_port->scsi_host
* ata_port->host_set => ata_port->host
* ata_port_info->host_flags => ata_port_info->flags
* ata_(.*)host_set(.*)\(\) => ata_\1host\2()
The leading underscore in ata_probe_ent->_host_flags is to avoid
reusing ->host_flags for different purpose. Currently, the only user
of the field is libata-bmdma.c and probe_ent itself is scheduled to be
removed.
ata_port->host is reused for different purpose but this field is used
inside libata core proper and of different type.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
