| Age | Commit message (Collapse) | Author |
|---|
|
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA
controller. NCQ function is disable by default, you can enable it
with 'swncq=1'. NCQ will be turned off if the drive is Maxtor on
MCP51 or MCP55 rev 0xa2 platform.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Kuan Luo <kluo@nvidia.com>
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Zoltan Boszormenyi <zboszor@dunaweb.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently. This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.
If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link. If ATA_DEFER_PORT, until a qc completes
on any link. The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.
ops->qc_defer() replaces fixed ata_scmd_need_defer(). For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented. ahci and
sata_sil24 are converted to use ata_std_qc_defer().
ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.
IMHO, this shouldn't cause any noticeable performance issues as
* for most cases deferring occurs rarely (except for NCQ-aware
cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
completes which usually is a very long time cpu-wise.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bump the versions for drivers that were modified, but had not already
had a version number bump.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert ->scr_read/write callbacks to return error code to better
indicate failure. This will help handling of SCR_NOTIFICATION.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Requiring LLDs to format multiple error description messages properly
doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation. __ata_ehi_push_desc() is the raw
version without the automatic separator.
While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
With PCI resource fix up for legacy hosts. We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts. Only IRQ requesting needs to be different.
Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead. This
simplifies code a lot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Only the ADMA entry was supposed to be able to change queue depth.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The sata_nv driver was missing the change_queue_depth hook in the SCSI host
template which the other NCQ-capable libata drivers had. This made it impossible
to change the queue depth by user request. Add this in.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
As with all other drivers, sata_nv's hpriv is allocated with
devm_kzalloc() and there's no need to free it explicitly. Kill
nv_remove_one() which incorrectly used kfree() instead of devm_kfree()
and use ata_pci_remove_one() directly.
Original fix is from Peer Chen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv
driver is unnecessary. Also the wildcard sometimes cause sata_nv driver to
be loaded for AHCI controllers,which is not as expected.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller. This never became actually
necessary and the related code always has been subtly broken one way
or the other. Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases. Exotic
cases can simply dealt within LLDs as necessary.
This patch removes port_mask handling in SFF init helpers. SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore. All information is carried via port_info. n_ports argument
is dropped and always two ports are allocated. LLD can tell SFF to
skip certain port by marking it dummy. Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.
This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic. The following changes
are made...
* ata_pci_init_native_host() and ata_init_legacy_host() both now try
to initialized whatever they can and mark failed ports dummy. They
return 0 if any port is successfully initialized.
* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
take n_ports argument. All info should be specified via port_info
array. Always two ports are allocated.
* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
* port_info handling in all LLDs are standardized - all port_info
arrays are const stack variable named ppi. Unless the second port
is different from the first, its port_info is specified as NULL
(tells libata that it's identical to the last non-NULL port_info).
* pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an
on-stack copy instead as ata_piix does.
* pata_uli: It has 4 ports instead of 2. Don't use
ata_pci_prepare_native_host(). Allocate the host explicitly and use
init helpers. It's simple enough.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch fixes some problems with ADMA-capable controllers with
regard to freeze, thaw and irq_clear libata callbacks. Freeze and
thaw didn't switch the ADMA-specific interrupts on or off, and more
critically the irq_clear function didn't respect the restriction that
the notifier clear registers for both ports have to be written at
the same time even when only one port is being cleared. This could
result in timeouts on one port when error handling (i.e. as a result
of hotplug) occurred on the other port.
As well, this fixes some issues in the interrupt handler: we shouldn't
check any ADMA status if the port has ADMA switched off because of
an ATAPI device, and it also checks to see if any ADMA interrupt has
been raised even when we are in port-register mode.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.
* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.
* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.
There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.
2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.
3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.
If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.
* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.
* Spin up waiting is to be removed and not converted to honor
deadline.
* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert drivers which use ata_pci_init_native_mode() to new init
model. ata_pci_init_native_host() is used instead. sata_nv, sata_uli
and sata_sis are in this category.
Tested on nVidia Corporation CK804 Serial ATA Controller [10de:0054]
in both BMDMA and ADMA mode.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Reading from the ATA shadow registers while we are in ADMA mode may cause
undefined behavior. Don't read the ATA status register when completing
commands for this reason, it shouldn't be needed as the controller will
notify us if the command failed. Also, don't allow commands with result
taskfile requested to execute in ADMA mode, since that requires accessing
the shadow registers. We also still need to override tf_read since libata
will read the result taskfile on a command failure, and we need to go into
port register mode before allowing this.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Commit 721449bf0d51213fe3abf0ac3e3561ef9ea7827a added support for using the
ADMA notifier bits to determine which commands to check for completion.
However there have been reports that this causes command timeouts in certain
cases. This is still being investigated. In addition, apparently the notifiers
won't work if ADMA is disabled on the other port as a result of an ATAPI device
being connected, and we don't handle this case properly.
For now, just restore the previous behavior of checking all active commands
to see if they are complete, without relying on the notifiers.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
No code changes.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Recently Tejun wrote a patch to ahci.c to make it raise a HSM violation
if the drive attempted to complete a tag that wasn't outstanding. We could
run into the same problem with sata_nv ADMA. This adds code to raise a HSM
violation error if the controller gives us a notifier tag that isn't
outstanding, since the drive may be issuing spurious completions.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sata_nv implemented its own copies of the BMDMA helper functions for ADMA,
since the ADMA BMDMA status registers are PIO while the other registers
are MMIO, and this was the only way to handle this previously. Now that
we have iomap support, the standard routines should just work, so use them.
The only thing we need to override as far as ADMA and BMDMA is the
post_internal_cmd callback, where we should only call ata_post_internal_cmd
if we are in port-register mode.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
We already have code that handles hotplug interrupt indications in ADMA
mode, this turns on the control flag that actually enables these interrupts.
Also fixes some cases in the same functions where a 16-bit register was read
using a readl instead of a readw.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The hardware provides us a notifier register that indicates what command
tags have completed. Use this to determine which CPBs to check, rather
than blindly checking all active CPBs. This should provide a minor
performance win, since if the controller has touched some of these
incomplete CPBs, accessing them will likely result in a cache miss.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This edits the taskfile setup to more closely match the way that libata
sends the taskfile for other controllers. This avoids putting taskfile writes
into the CPB buffer that are not needed according to the taskfile flags.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Clean up the initialization of the CPB and APRD structures so that we
strictly follow the rules for ordering of writes to the CPB flags and
response flags, and prevent duplicate initialization.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When error handling occurs with pending commands, output the contents
of the next CPB count and next CPB index registers as well as the others,
since these may be useful for debugging.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch appears to solve some problems with commands timing out in
cases where an NCQ command is immediately followed by a non-NCQ command
(or possibly vice versa). This is a rather ugly solution, but until we
know more about why this is needed, this is about all we can do.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some debug output in the ADMA error_handler function was removed recently,
but it may be useful in certain cases, like NCQ commands timing out. Add it
back in, but make it a bit more intelligent so that it only prints if
command(s) are active and only prints the CPBs for those commands.
That way it won't spew at inappropriate times like suspend/resume.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ADMA-capable controllers provide a bit in the status register that appears
to indicate that the controller detected an SError condition. Update sata_nv
to detect this and trigger error handling in order to handle the fault.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ata_pci_device_do_resume can fail if the PCI device couldn't be re-enabled.
Update sata_nv to propagate the return value from this call and to not try
to do any other resume activities if it fails. Fixes a compile warning.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update sata_nv to wait for the controller to indicate via the status
register that it has entered the requested state when switching between
ADMA mode and register mode. This issue came up recently when debugging
some problems with cache flush command timeouts and while it didn't appear
to fix that problem, this is something we should likely be doing in any
case.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some problems showed up recently with cache flush commands timing out on
sata_nv. Previously these commands were always handled by transitioning to
legacy mode from ADMA mode first. The timeout problem was worked around
already by a change to the interrupt handling code for legacy mode, but for
non-data commands like these it appears we can handle them in ADMA mode, so
the switch to legacy mode is not needed.
This patch changes the behavior so that we use ADMA mode to submit
interrupt-driven commands with ATA_PROT_NODATA protocol. In addition to
avoiding the problem mentioned above entirely, this avoids the overhead of
switching to legacy mode and back to ADMA mode for handling cache flushes.
When handling non-DMA-mapped commands, we leave the APRD blank and clear
the NV_CPB_CTL_APRD_VALID field in the CPB so the controller does not
attempt to read it.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This cleans up a few issues with the error handling in sata_nv in ADMA mode
to make it more consistent with other NCQ-capable drivers like ahci and
sata_sil24:
- When a command failed, we would effectively set AC_ERR_DEV on the
queued command always. In the case of NCQ commands this prevents libata
from doing a log page query to determine the details of the failed
command, since it thinks we've already analyzed. Just set flags in the
port ehi->err_mask, then freeze or abort and let libata figure out what
went wrong.
- The code handled NV_ADMA_STAT_CPBERR as a "really bad error" which
caused it to set error flags on every queued command. I don't know
exactly what this flag means (no docs, grr!) but from what I can guess
from the standard ADMA spec, it just means that one or more of the CPBs
had an error, so we just need to go through and do our normal checks in
this case.
- In the error_handler function the code would always dump the state of
all the CPBs. This output seems redundant at this point since libata
already dumps the state of all active commands on errors (and it also
triggers at times when it shouldn't, like when suspending). Take this
out.
[akpm@osdl.org: many coding-style fixes]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Allen Martin <AMartin@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch is against each libata driver.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.
In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.
In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.
* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update libata LLDs to use devres. Core layer is already converted to
support managed LLDs. This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path. For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.
As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down. Note that freezing is enough in many cases
and ports are automatically frozen before being detached.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Thoughts from Jeff & company on merging the patch below into libata-dev?
This has been in the -mm tree for over a month now, I haven't heard any
complaints about regressions..
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Most of these contributed by that mysterious figger known as A.C.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Several people reported issues with certain drive commands timing out on
sata_nv controllers running in ADMA mode. The commands in question were
non-DMA-mapped commands, usually FLUSH CACHE or FLUSH CACHE EXT.
From experimentation it appears that the NV_INT_DEV indication isn't
always set when a legitimate command completion interrupt is received on
a legacy-mode command, at least not on these controllers in ADMA mode.
When a command is pending on the port, force the flag on always in the
irq_stat value before calling nv_host_intr so that the drive busy state
is always checked by ata_host_intr.
This also fixes some questionable code in nv_host_intr which called
ata_check_status when a command was pending and ata_host_intr returned
"unhandled". If the device interrupted at just the wrong time this could
cause interrupts to be lost.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The content of memory map io of BAR5 have been change from MCP65 then
sata_nv can't work fine on the platform based on MCP65 and MCP67, so move
their IDs from sata_nv.c to ahci.c.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
The attached patch against 2.6.19-rc6-mm1 fixes some problems in sata_nv
with ATAPI devices on controllers running in ADMA mode. Some of the
logic in the nv_adma_bmdma_* functions was inverted causing a bunch of
warnings and caused those functions not to work properly. Also, when an
ATAPI device is connected, we need to use the legacy DMA engine. The
code now disables the PCI configuration register bits for ADMA so that
this works, and ensures that no ATAPI DMA commands go through until this
is done.
Fixes Bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=7538
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
NV controllers sometimes fail to perform softreset after hotplug.
Make it use hardreset to resume link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
