| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit d05c7a80cf39ae7d0f8d0c3e47c93d51fcd393d3,
which included changes which should go via other subsystem
maintainers.
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Limit ATAPI DMA to R/W commands only for TORiSAN DVD drives (take 3)
libata: Limit max sector to 128 for TORiSAN DVD drives (take 3)
libata: Clear tf before doing request sense (take 3)
libata: reorder HSM_ST_FIRST for easier decoding (take 3)
libata bugfix: preserve LBA bit for HDIO_DRIVE_TASK
2.6.21 fix lba48 bug in libata fill_result_tf()
|
|
This adds some NCQ blacklist entries taken from the Silicon Image 3124/3132
Windows driver .inf files. There are some confirming reports of problems
with these drives under Linux (for example http://lkml.org/lkml/2007/3/4/178)
so let's disable NCQ on these drives.
[ I'm personally starting to wonder whether we shouldn't disable NCQ by
default, and perhaps have a white-list. There seems to be a *lot* of
drives that do this wrong.. - Linus ]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
patch 4/4:
Limit ATAPI DMA to R/W commands only for TORiSAN DRD-N216 DVD-ROM drives
(http://bugzilla.kernel.org/show_bug.cgi?id=6710)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
patch 3/4:
The TORiSAN drive locks up when max sector == 256.
Limit max sector to 128 for the TORiSAN DRD-N216 drives.
(http://bugzilla.kernel.org/show_bug.cgi?id=6710)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
patch 2/4:
Clear tf before doing request sense.
This fixes the AOpen 56X/AKH timeout problem.
(http://bugzilla.kernel.org/show_bug.cgi?id=8244)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Preserve the LBA bit in the DevSel/Head register for HDIO_DRIVE_TASK.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Current 2.6.21 libata does the following:
void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
tf->command = ata_check_status(ap);
...
if (tf->flags & ATA_TFLAG_LBA48) {
iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr);
tf->hob_feature = ioread8(ioaddr->error_addr);
...
}
}
...
static void fill_result_tf(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
ap->ops->tf_read(ap, &qc->result_tf);
qc->result_tf.flags = qc->tf.flags;
}
Based on this, those last two statements fill_result_tf()
appear to me to be in the wrong order, in that the tf->flags
are uninitialized at the point where tf_read() is invoked.
So for lba48 commands, tf_read() won't be reading back the
full lba48 register contents..
Correct?
This patch corrects fill_result_tf() so that the flags
get copied to result_tf before they are used by tf_read().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
I've seen this several times on this drive, completely reproducible.
Once it has hung, power needs to be cut from the drive to recover it, a
simple reboot is not enough. So I'd suggest disabling NCQ on this
drive.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this applied, my machine has stopped all those painful messages.
dmesg now says :
root@riri:/Kernels# dmesg | grep LBA
ata1.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
ata2.00: 640 sectors, multi 1: LBA
ata3.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
Signed-off-by: Paul Rolland <rol@as2917.net>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
In LBA48 mode we have to help the controller to get anything to work. The
chip provides a register giving word counts meant for ATAPI use which we
can use. However we need to load the count in words not bytes..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
For drive side cable detection to work correctly, drives need to be
identified backwards such that the slave device releases PDIAG- before
the mater drive tries to detect cable type. ata_bus_probe() was fixed
by commit f31f0cc2f0b7527072d94d02da332d9bb8d7d94c but the new EH path
wasn't fixed. This patch makes new EH path do IDENTIFY backwards.
ata_dev_configure() for new devices are still performed master first.
This is to keep the detection messages in forward order.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
There is a HW issue in ATI SB600 SATA that PxSERR.E should not be
set on some conditions, for example, when there is no media in SATA
CD/DVD drive or media is not ready, AHCI controller fails to execute
ATAPI commands and reports PORT_IRQ_TF_ERR, but ATI SB600 SATA
controller sets PxSERR.E at the
same time, which is not necessary.
This patch is just to ignore the INTERNAL ERROR in such case.
Without this patch, ahci error handler will report many errors as
below:
----------- cut from dmesg -----------
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0
res 51/24:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error)
-------- end cut ---------
Signed-off-by: Conke Hu <conke.hu@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Not yet ready to turn on ATA ACPI by default, for either PATA or SATA.
Also, rename the global-scope module parameter variable 'noacpi' to
something more libata-specific, reducing the potential for namespace
collision.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
As per compact flash specifications, the default
irq mode upon cf insertion is pulse mode. this patch fixes
the driver to cope with that.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
pata_ixp4xx_cf dodged dont-clear-drvdata-in-LLD bombing run as it used
platform_set_drvdata() instead of dev_set_drvdata(). This causes OOPS
on devres host release. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Warning(linux-2621-rc3g7/drivers/ata/libata-core.c:842): No description found for parameter 'unknown'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Regions are requested twice during initialization causing the second
one to fail. This is regression introduced during iomap conversion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
PATA_SCC depends on PPC_CELLEB. (not PPC_IBM_CELL_BLADE)
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add Adaptec 1220SA (SIL3132) to devices claimed by sata_sil24
Patch generated against 2.6.20.2
Signed-off-by: Jamie Clark <jclark@metaparadigm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
->prereset() returns -ENOENT to tell libata that the port is empty and
reset sequencing should be stopped. This is not an error condition.
Update ata_eh_reset() such that it sets device classes to ATA_DEV_NONE
and return success in on -ENOENT. This makes spurious error message
go away.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
The ACPI specification states, and BIOS implementations depend on,
_STM being called before _GTF.
SATA does this, but PATA does not. So for now, simply
prevent execution of _GTF on PATA devices. Longer term we
should implement ACPI support for PATA devices in libata.
Signed-off-by: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
host->ops->host_stop() might access ports. Free ports after
host_stop.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Commit 721449bf0d51213fe3abf0ac3e3561ef9ea7827a added support for using the
ADMA notifier bits to determine which commands to check for completion.
However there have been reports that this causes command timeouts in certain
cases. This is still being investigated. In addition, apparently the notifiers
won't work if ADMA is disabled on the other port as a result of an ATAPI device
being connected, and we don't handle this case properly.
For now, just restore the previous behavior of checking all active commands
to see if they are complete, without relying on the notifiers.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Recently I got my hands on nVidia's MCP61 PM-AM board, and
it contains IDE chip configured by BIOS with only primary
channel enabled. This confuses code which probes for
device DMA capabilities - it gets 0x60 (happy duplex
device) from primary channel BMDMA, but 0xFF (nobody here)
from secondary channel BMDMA. Due to this code then believes
that chip is simplex. I do not address this problem in
my patch, as I'm not sure how to handle this. Probably
ata_pci_init_one should have bitmap of enabled/possible
interfaces instead of their count, but it looks like
quite intrusive change, and maybe we do not care - for device
with only one channel simplex and regular DMA engines are
same.
But making device simplex pointed out that support for
DMA on simplex devices is currently broken - ata_dev_xfermask
tests whether device is simplex and if it is whether DMA
engine was assigned to this port. If not then it strips
out DMA bits from device. Problem is that code which assigns
DMA engine to port in ata_set_mode first detect device
mode and assigns DMA engine to channel only if some DMA
capable device was found.
And as xfermask stripped out DMA bits, host->simplex_claimed
is always NULL with current implementation.
By allowing DMA either if simplex_claimed is NULL or if it
points to current port DMA can be finally used - it gets
assigned to first port which contains any DMA capable
device.
Before:
pata_amd 0000:00:06.0: version 0.2.8
PCI: Setting latency timer of device 0000:00:06.0 to 64
ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
scsi4 : pata_amd
ata5.00: ATAPI, max UDMA/66
ata5.00: simplex DMA is claimed by other device, disabling DMA
ata5.00: configured for PIO4
scsi5 : pata_amd
ata6: port disabled. ignoring.
ata6: reset failed, giving up
scsi 4:0:0:0: CD-ROM ATAPI DVD W DH16W1P LG12 PQ: 0 ANSI: 5
After:
pata_amd 0000:00:06.0: version 0.2.8
PCI: Setting latency timer of device 0000:00:06.0 to 64
ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
scsi4 : pata_amd
ata5.00: ATAPI, max UDMA/66
ata5.00: configured for UDMA/33
scsi5 : pata_amd
ata6: port disabled. ignoring.
ata6: reset failed, giving up
scsi 4:0:0:0: CD-ROM ATAPI DVD W DH16W1P LG12 PQ: 0 ANSI: 5
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
A while ago I modified the libata code so that drivers can return -ENOENT
for unknown ports not fiddle with the EH flags and print stuff directly.
Somewhere along the line ata_piix didn't get fully converted.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
For 2.6.20 it mostly used to just not work, for 2.6.21-rc it crashes, this
seems to be down to luck (bad or good). The libata-acpi code needs to
avoid doing PCI work on non-PCI devices. This is one hack although it's
not pretty and perhaps there is a "right" way to check if a struct device
* is PCI ?
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix wrong "port" calculations in pdc202xx_{configure_piomode,set_dmamode}()
They were broken for all configurations except one (master device on primary
channel, no other devices) and as a result device settings + PIO/DMA timings
were being programmed into the wrong PCI registers. This could result in
a large variety of problems including data corruption, hangs etc. (depending
on devices used and your luck :-).
ap->port_no ap->devno used PCI registers correct PCI registers
0 0 0x60-0x62 0x60-0x62
0 1 0x62-0x64 0x64-0x66
1 0 0x64-0x66 0x68-0x6a
1 1 0x66-0x68 0x6c-0x6e
Also forward port recent fixes from drivers/ide pdc202xx_old driver:
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
and finally bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
pata_legacy fails to detect the disk on my old ISA/VLB 486:
it starts to probe io=0x1f0 ctr=0x3f6 irq=15, complains
loudly about IDENTIFYs timing out, and finally fails.
(Sorry I couldn't capture the kernel's boot messages.)
It turns out that the driver's mapping from io to irq in
legacy_irq[] is wrong: index 0 for io=0x1f0 has irq=15 but
should have irq=14, and index 1 for io=0x170 has irq=14 but
should have irq=15. This is confirmed by a comparison with
include/asm-i386/ide.h:ide_default_irq().
This patch swaps the first two elements in legacy_irq[],
which makes pata_legacy work on my 486.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds the Intel ICH9M RAID controller DID for SATA support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Conditionalize all PM related stuff in libata core layer using
CONFIG_PM.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some LLDs were missing scsi device PM callbacks while having host/port
suspend support. Add missing ones.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The QDI init code contains some bugs which mean it only works if you have
a test setup that causes both a successful and failed probe. Fix this
Found by Philip Guo
(Who found it working on code analysis tools not running VLB IDE
controllers)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Trivial comment fix, taken out of a larger Alan Cox patch.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Alan Cox noticed several hooks in pata_* drivers were missing, when
he authored his ->cable_detect hook patches. This patch extracts
just those fixes from Alan's patches, adding the necessary hooks
(usually ->freeze, ->thaw, and ->post_internal_cmd) to the drivers.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
2.6.21-rc has horrible problems with libata and PATA cable types (and
thus speeds). This occurs because Tejun fixed a pile of other bugs and
we now do cable detect enforcement for drive side detection properly.
Unfortunately we don't do the process around cable detection right. Tejun
identified the problem and pointed to the right Annex in the spec, this patch
implements the needed changes.
The basic requirement is that we have to identify the slave before the
master.
The patch switches the identify order so that we can do the drive side
detection correctly.
[NOTE: patch and description extracted from a larger work written
and signed-off-by Alan Cox]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The initial simplex handling code is fooled if you suspend and resume.
This also causes problems with some single channel controllers which
claim to be simplex.
The fix is fairly simple, instead of keeping a flag to remember if we
gave away the simplex channel we remember the actual owner. As the owner
is always part of the host_set we don't even need a refcount.
Knowing the owner also means we can reassign simplex DMA channels in
future hotplug code etc if we need to
Signed-off-by: Alan Cox <alan@redhat.com>
(and a signed-off for the patch I sent before while I remember)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Spurious SDB FIS during NCQ might not contain spurious completions.
It could be spurious TF update or invalid async notification. Treat
as HSM violation iff a spurious SDB FIS contains spurious completions;
otherwise, just whine once about it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make jmiron_ata quirk update pdev->class after programming the device
and update ahci and pata_jmicron such that they match class code
instead of checking function number manually. For ahci, it matches
for vendor and class. For pata_jmicron, it matches vendor, device and
class as IDE class isn't as well defined as AHCI class.
This makes jmicron device matching more conventional and script
friendly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Channel redirect and AHCI mode enable programmings are done via PCI
quirk for both probe and resume paths. Drop duplicate and possibly
unsafe device programming from pata_jmicron().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Blacklist FUJITSU MHT2060BH for NCQ. On this drive, NCQ works iff
queue depth is equal to or less than 4. Just turn it off.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mike Accetta <maccetta@laurelnetworks.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Kill unused local variable idx in sil24_fill_sg().
Spotted by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Clearing drvdata in ->remove_one causes NULL pointer deference. Clear
drvdata only in ata_host_release() after all resources are freed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bump versions based on changes submitted during 2.6.21 merge window.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
