| Age | Commit message (Collapse) | Author |
|---|
|
Use usb_endpoint_xfer_int() instead of direct use of constants.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move usbhid specific flags from global hid.h into local usbhid.h.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1146c) makes usbhid automatically call usbhid_set_leds()
for any device that supports the keyboard boot protocol.
In theory this should be perfectly safe. BIOSes send the LED output
report as part of their normal device initialization, so any keyboard
device supporting the boot protocol has to be able to handle it.
As a side effect, the hid-dell and hid-bright drivers are no longer
needed, and the Logitech keyboard driver can be removed from hid-lg.
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When computing the maximal buffer size needed, we must take into
account that not only input reports can be numbered.
Pointed out in bugzilla #10467
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some devices have no input interrupt endpoint. These won't be handled
by usbhid, but currently they are not refused and reside on hid bus.
Perform this checking earlier so that we refuse to control such
a device early enough (and not pass it to the hid bus at all).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
`stop' left out usbhid->urb* pointers and so the next `start' thought
it needs to allocate nothing and used the memory pointers previously
pointed to. This led to memory corruption and device malfunction.
Also don't forget to clear disconnect flag on start which was left set
by the previous `stop'.
This fixes
echo DEVICE > /sys/bus/hid/drivers/DRIVER/unbind
echo DEVICE > /sys/bus/hid/drivers/DRIVER/bind
failures.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When suspending, make sure that the timer is not running
any more.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Usbhid structure is allocated on start invoked only from probe
of some driver. When there is no driver, the structure is null
and causes null-dereference oopses.
Fix it by allocating the structure on probe and disconnect of
the device itself. Also make sure we won't race between start
and resume or stop and suspend respectively.
References: http://bugzilla.kernel.org/show_bug.cgi?id=11827
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for Sony Vaio VGX-TP1E
HID: fix lock imbalance in hiddev
HID: fix lock imbalance in hidraw
HID: fix hidbus/appletouch device binding regression
HID: add hid_type to general hid struct
HID: quirk for OLED devices present in ASUS G50/G70/G71
HID: Remove "default m" for Thrustmaster and Zeroplus
HID: fix hidraw_exit section mismatch
HID: add support for another Gyration remote control
Revert "HID: Invert HWHEEL mappings for some Logitech mice"
|
|
Don't forget to unlock_kernel() in hiddev_ioctl_usage().
Added in 7961df16819085b8a357720d89d0239036e6af2a
(HID: Switch hiddev to unlocked_ioctl).
Corresponing sparse warning:
drivers/hid/usbhid/hiddev.c:515:10: warning: context imbalance in 'hiddev_ioctl_usage': wrong count at exit
drivers/hid/usbhid/hiddev.c:515:10: context 'kernel_lock': wanted 0, got 1
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add type to the hid structure to distinguish to which device type
(now only mouse) we are talking to. Needed for per device type ignore
list support.
Note: this patch leaves the type as unknown for bluetooth devices,
there is not support for this in the hidp code.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
There were two stragglers that got missed in the last merge of the HID tree that forgot to change the warn() calls to dev_warn(). This patch fixes them up.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit 8006479c9b75fb6594a7b746af3d7f1fbb68f18f introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.
Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.
In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hid-ff.c now calls only pidff (generic driver), the special ones are now
in separate drivers. Invoke pidff on all non-special directly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move the force feedback processing into a separate module.
[jkosina@suse.cz: fix Kconfig texts a little bit]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This seems to be the very same device, as already supported Smartjoy
dual Plus, but with slightly different vendor ID. Let's support this
one too.
Reported-by: David Ashley <dashxdr@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Merge the logitech force feedback processing directly into logitech
driver from the usbhid core.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move the handling of the leds resetting from the core to
the dell and logitech drivers.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Remove support for both dynamic and static report descriptor
quirks. There is no longer rdesc code which it would support,
so it's useless.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move them from the core code to a separate driver.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Bring switch and cases into coding style and save thus some
indentation to make the code tighter.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move them from the core code to a separate driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move ignore quirks from usbhid-quirks into hid-core code. Also don't output
warning when ENODEV is error code in usbhid and try ordinal input in hidp
when that error is returned.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move them from the core and input code to a separate driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move ids from hid-quirks.c into separate file, since it will be needed in
more than one place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Next step for complete hid bus, this patch includes:
- call parser either from probe or from hid-core if there is no probe.
- add ll_driver structure and centralize some stuff there (open, close...)
- split and merge usb_hid_configure and hid_probe into several functions
to allow hooks/fixes between them
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Make a bus from hid core. This is the first step for converting all the
quirks and separate almost-drivers into real drivers attached to this bus.
It's implemented to change behaviour in very tiny manner, so that no driver
needs to be changed this time.
Also add generic drivers for both usb and bt into usbhid or hidp
respectively which will bind all non-blacklisted device. Those blacklisted
will be either grabbed by special drivers or by nobody if they are broken at
the very rude base.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This driver adds support for the multitouch trackpad on the new
Apple Macbook Air and Macbook Pro Penryn laptops. It replaces the
appletouch driver on those computers, and integrates well with the
synaptics driver of the Xorg system.
[dtor@mail.ru: various cleanups]
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
This patch completely removes the dependency of usbkbd and usbmouse drivers
on usbhid code.
usbkbd/usbmouse drivers are not needed in the vast majority of cases anyway,
and they shouldn't be loaded in standard configurations at all. They are supposed
to be as trivial as possible, and searching for HID_QUIRK_IGNORE can even be
bad in some cases.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Logitech DiNovo desktop needs the same quirk as other DiNovo
devices.
Reported-by: Farid Benamrouche <farid.benamrouche@free.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When usbmouse/kbd is set to build, USB_HID is never defined due to
the USB_HID!=y Kconfig rule. Test CONFIG_USB_HID_MODULE in both
drivers instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
