| Age | Commit message (Collapse) | Author |
|---|
|
* Add ->port_init_devs method to ide_hwif_t for a host specific
initialization of devices on a port. Call the new method from
ide_port_init_devices().
* Convert ht6560b, qd65xx and opti621 host drivers to use the new
->port_init_devs method.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use the same bit for IDE_HFLAG_CS5520 and IDE_HFLAG_VDMA host flags
(both are used only by cs5520 host driver currently).
* Add IDE_HFLAG_NO_IO32_BIT host flag and use it instead of ->no_io_32bit
ide_hwif_t field.
* Add IDE_HFLAG_NO_UNMASK_IRQS host flag, then convert dtc2278 and rz1000
host drivers to use it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out code initializing devices from ide_init_port() to
ide_port_init_devices().
* Call the new function from ide_device_add_all().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add BUG_ON(hwif->present) at the start of ide_probe_port().
* Move hwif_register() call (along with setting hwif->present) from
ide_probe_port() to ide_device_add_all().
As a result the port will be registered with the device tree _after_:
- probing both devices (if both are present)
- port reset (if hwif->reset is set)
- restoring local IRQs state and re-enabling port IRQ
While at it:
* Rename hwif_register() to ide_register_port().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out code for tuning devices from ide_probe_port()
to ide_port_tune_devices().
* Move ide_port_tune_devices() call from ide_probe_port()
to ide_device_add_all().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Reserve/release I/O resources in ide_device_add_all() instead of
ide_probe_port().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Make probe_hwif() return an error value.
While at it:
* Remove comment about MAX_DRIVES == 2 limitation (it is not special to
probe_hwif(), it is a general assumption taken by a lot of IDE code).
* Rename probe_hwif() to ide_probe_port().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* BUG_ON() early if 'hwif->next == hwif' and there is a 'match' hwgroup.
* Remove printk() for impossible condition and add a BUG_ON(hwgroup->drive)
to match code in ide_unregister().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Since kmalloc_node() is called with __GFP_ZERO flag there is no need to
explicitly zero hwgroup fields.
While at it:
* Use 'hwif' instead of 'hwif->drives[0].hwif' for kmalloc_node() call.
* Fix whitespace damage.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Call hwif_init() only if hwif->present is set.
* If hwif_init() fails clear hwif->present.
* Remove hwif->present manipulations from hwif_init().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move wait_hwif_ready() documentation before this function.
* Fix trailing whitespaces.
* s/wait-for-busy/wait-for-non-busy/
* Remove no longer valid comment about the current code behavior.
* Docbook-ize it.
* Rename wait_hwif_ready() to ide_port_wait_ready().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
It could be that I/O resources are busy because some other host driver
has already claimed them so don't unregister the devices.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The last years stuff and a trip down memory lane...
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Delete filenames/versions from comments.
I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.
While at it:
* Remove unused VERSION define from ide.c.
* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.
While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ide_dump_identify() debug helper for dumping raw identify data in
the hdparm friendly format (== the identify data can be extracted from
dmesg output and passed to hdparm --Istdin).
* Dump identify data in ide-probe.c::do_identify() if DEBUG is enabled.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_busy_sleep() helper and use it in do_probe(),
enable_nest() and probe_hwif().
As a nice side-effect this fixes a minor bug in do_probe()
(the code was reading status register without any delay).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix build break of powerpc holly_defconfig:
In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)
There's no need to have a sized array in the prototype, might as well
turn it into a pointer.
It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename ide_device_add() to ide_device_add_all() and make it accept
'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.
* Add ide_device_add() wrapper for ide_device_add_all().
* Convert ide_generic_init() to use ide_device_add_all().
* Remove no longer needed ideprobe_init().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add hwif->chipset fixup identical to the one in ideprobe_init()
to ide_device_add().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
After hwif_register_devices() IDE devices are ready to be used so
the way in which ide_device_add() works currently is racy for hosts
with serialized / IRQ sharing interfaces.
Fix ide_device_add() by looping over interfaces for probe_hwif(),
hwif_init() and hwif_register_devices() operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* ->dma_off_quietly is always called before ide_set_dma()
so the call can be moved inside ide_set_dma().
* ide_dma_check() doesn't touch hardware so ->dma_off_quietly
call for 'rc == -1' case is redundant, remove it.
* '0' and '-1' are the only values returned by ide_dma_check()
so remove dead code for other cases.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove stale ide.h "configuration options":
* INITIAL_MULT_COUNT - always defined to 0
* SUPPORT_SLOW_DATA_PORTS - unused
* OK_TO_RESET_CONTROLLER - always defined to 1
* DISABLE_IRQ_NOSYNC - always defined to 0
Leave SUPPORT_VLB_SYNC (defined to 0 for CRIS and FRV, otherwise to 1)
for now but disallow overriding it by <asm/ide.h>.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
IRQF_DISABLED is not needed because the first thing that ide_intr()
(IDE IRQ handler) does is calling spin_lock_irqsave() which disables
local IRQs (IRQ unmasking is later handled by drive->unmask).
kernel/irq/handle.c:
irqreturn_t handle_IRQ_event(unsigned int irq, struct irqaction *action)
...
if (!(action->flags & IRQF_DISABLED))
local_irq_enable_in_hardirq();
do {
ret = action->handler(irq, action->dev_id);
if (ret == IRQ_HANDLED)
status |= action->flags;
retval |= ret;
action = action->next;
} while (action);
...
drivers/ide/ide-io.c:
irqreturn_t ide_intr (int irq, void *dev_id)
...
spin_lock_irqsave(&ide_lock, flags);
...
spin_unlock(&ide_lock);
...
if (drive->unmask)
local_irq_enable_in_hardirq();
...
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
This moves the block devices to /sys/class/block. It will create a
flat list of all block devices, with the disks and partitions in one
directory. For compatibility /sys/block is created and contains symlinks
to the disks.
/sys/class/block
|-- sda -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda
|-- sda1 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda1
|-- sda10 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda10
|-- sda5 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda5
|-- sda6 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda6
|-- sda7 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda7
|-- sda8 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda8
|-- sda9 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda9
`-- sr0 -> ../../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0
/sys/block/
|-- sda -> ../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda
`-- sr0 -> ../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add missing checks for control register existence (some legacy m68k specific
IDE controllers don't have it). Also use drive->ctl while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There is a problem in some hardware where the kernel will stall for
35 seconds waiting for disks that don't exist. This patch will skip
waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe"
as a kernel option and the disk is not marked as 'present' (like when
you set the geometry by hand).
If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for
that drive. Even if there would be a drive there and it is still busy
afterwards it should not matter since it isn't probed for later.
The code also honors the MAX_DRIVES variable instead of assuming that
there will be two harddrives on the bus.
Bart: minor cleanups
Signed-off-by: Jonas Stare <jonas.stare@purplescout.se>
CC: Andrew Morton <akpm@linux-foundation.org>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Terminates id->model string before invoking strstr() in do_identify().
Signed-off-by: Tejun Heo <tj@home-tj.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
git-drivers/ide/ide-probe.c: In function 'hwif_init':
drivers/ide/ide-probe.c:1327: error: implicit declaration of function
'sg_init_table'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
* Add ide_device_add() helper and convert host drivers to use it
instead of open-coded variants.
* Make ide_pci_setup_ports() and do_ide_setup_pci_device()
take 'u8 *idx' argument instead of 'ata_index_t *index'.
* Remove no longer needed ata_index_t.
* Unexport probe_hwif_init() and make it static.
* Unexport ide_proc_register_port().
There should be no functionality changes caused by this patch
(sgiioc4.c: ide_proc_register_port() requires hwif->present
to be set and it won't be set if probe_hwif_init() fails).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ->fixup method to ide_hwif_t.
* Set hwif->fixup in ide_pci_setup_ports() to d->fixup.
* Use hwif->fixup in probe_hwif().
* Use probe_hwif_init() instead of probe_hwif_init_with_fixup() in
ide_setup_pci_device().
* Add 'fixup' argument to ide_register_hw() and use it to set hwif->fixup,
update all ide_register_hw() users accordingly.
* Convert ide-cs/delkin_cb host drivers to use ide_register_hw().
* Restore hwif->fixup in ide_hwif_restore().
* Remove ide_register_hw_with_fixup(), probe_hwif_init_with_fixup()
and 'fixup' argument from probe_hwif().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add hwif_register_devices() helper to fix code duplication between
probe_hwif_init_with_fixup() and ideprobe_init(). Also remove stale
comment while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma]
and then remove no longer needed hwif->no_lba48[_dma]. As a side-effect
this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
ATAPI devices with broken DMA support should be handled by DMA blacklist
and for debugging purposes we have new shiny "hdx=nodma" kernel paremeter.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Need to probe slave device first to make it release PDIAG-
(this is required for correct device side cable detection).
Based on libata commit f31f0cc2f0b7527072d94d02da332d9bb8d7d94c.
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
