aboutsummaryrefslogtreecommitdiff
path: root/drivers/ide/pci
AgeCommit message (Collapse)Author
2008-02-26ide: skip probing port if "hdx=noprobe" was used for both devices on itBartlomiej Zolnierkiewicz
* Skip probing port if "hdx=noprobe" parameter was used for both devices on it. * Obsolete "idex=noprobe" parameter - it only works for ide_generic, cmd640 and PCI hosts in Compatibility mode (on alpha/x86/ia64/m32r/mips/ppc32). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-26hpt366: fix section mismatch warningsSam Ravnborg
hpt366: fix section mismatch warnings Fix following warnings: WARNING: o-sparc64/vmlinux.o(.data+0x195a38): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt370 WARNING: o-sparc64/vmlinux.o(.data+0x195a40): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt370a WARNING: o-sparc64/vmlinux.o(.data+0x195a48): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt372 WARNING: o-sparc64/vmlinux.o(.data+0x195a50): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt372n Replace a static array with a small switch resulting in more readable code. Mark the pci table __devinitconst. A lot of variables are const but annotated __devinitdata. Annotating them __devinitconst would cause a section type conflict error when build for 64 bit powerpc. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-19via82cxxx: add new PCI id for cx700Andrew Smith
[bart: manually ported it over via82cxxx changes] From: Andrew Smith <asmith@tranquility.fsbusiness.co.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-11pdc202xx_old: always enable burst modeBartlomiej Zolnierkiewicz
Alan has noticed that distros always enabled burst mode (+ datasheet confirms that it is the right thing to do). Thus fix pdc202xx_old host driver to do it unconditionally and remove no longer needed CONFIG_PDC202XX_BURST option. Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-11cs5520: remove stale commentBenjamin Herrenschmidt
Remove stale comment from the cs5520 IDE driver. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-06ide: remove write-only ->sata_misc[] from ide_hwif_tBartlomiej Zolnierkiewicz
* Remove write-only ->sata_misc[] from ide_hwif_t. * Remove no longer used SATA_{MISC,PHY,IEN}_OFFSET defines. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-06ide-pci-generic: kill the unused ifdef/endif/MODULE codeDenis Cheng
with module_param macro, the __setup code can be killed now: const __setup("all-generic-ide", ide_generic_all_on); and the module name "generic.ko" is not descriptive to its functionality, can be changed in Makefile, the "ide-pci-generic.ko" is better. the ide-pci-generic.all-generic-ide parameter also documented in Documentation/kernel-parameters.txt Signed-off-by: Denis Cheng <crquan@gmail.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: remove SATA_*_REG macrosBartlomiej Zolnierkiewicz
* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of SATA_{ERROR,STATUS}_REG macros. * Remove no longer needed SATA_*_REG macros. While at it: * Remove needless SATA Status register read from sil_sata_reset_poll(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02trm290: use ide_execute_command()Bartlomiej Zolnierkiewicz
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: add ->port_init_devs method to ide_hwif_tBartlomiej Zolnierkiewicz
* Add ->port_init_devs method to ide_hwif_t for a host specific initialization of devices on a port. Call the new method from ide_port_init_devices(). * Convert ht6560b, qd65xx and opti621 host drivers to use the new ->port_init_devs method. There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: add IDE_HFLAG_NO_{IO32_BIT,UNMASK_IRQS} host flagsBartlomiej Zolnierkiewicz
* Use the same bit for IDE_HFLAG_CS5520 and IDE_HFLAG_VDMA host flags (both are used only by cs5520 host driver currently). * Add IDE_HFLAG_NO_IO32_BIT host flag and use it instead of ->no_io_32bit ide_hwif_t field. * Add IDE_HFLAG_NO_UNMASK_IRQS host flag, then convert dtc2278 and rz1000 host drivers to use it. There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: fix ide_unregister() usage in host driversBartlomiej Zolnierkiewicz
bast-ide.c/ide-cs.c/delkin_cb.c: * Don't set 'restore' flag for ide_unregister() when initializing new interface. rapide.c/ide-pnp.c/ide-cs.c/ide_platform.c/au1xxx-ide.c/delkin_cb.c/scc_pata.c: * Don't set 'init_default' and 'restore' flags for ide_unregister() when removing interface. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: add ide_deprecated_find_port() helperBartlomiej Zolnierkiewicz
* Factor out code for finding ide_hwifs[] slot from ide_register_hw() to ide_deprecated_find_port(). * Convert bast-ide, ide-cs and delkin_cb host drivers to use ide_device_add() instead of ide_register_hw() (while at it drop doing "ide_unregister()" loop which tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot cannot be find). This patch leaves us with only two ide_register_hw() users: - drivers/macintosh/mediabay.c - drivers/ide/ide.c Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: add 'init_default' and 'restore' arguments to ide_unregister()Bartlomiej Zolnierkiewicz
* Add 'init_default' (flag for calling init_hwif_default()) and 'restore' (flag for calling ide_hwif_restore()) arguments to ide_unregister(). * Update ide_unregister() users to set 'init_default' and 'restore' flags. * No need to set 'init_default' flag in ide_register_hw() if the setup done by init_hwif_default() is going to be overridden by ide_init_port_hw(). * No need to set 'init_default' and 'restore' flags in cleanup_module(). There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02pdc202xx_old: remove surplus initialiserAlan Cox
Bart: - drive-by CodingStyle fixups Signed-off-by: Alan Cox <alan@redhat.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: remove needless includes from PCI host driversBartlomiej Zolnierkiewicz
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: add ->cable_detect method to ide_hwif_tBartlomiej Zolnierkiewicz
* Add ->cable_detect method to ide_hwif_t. * Call the new method in ide_init_port() if: - the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78') - DMA initialization was successful (if hwif->dma_base is not set ide_init_port() sets hwif->ultra_mask to zero) - "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT') * Convert PCI host drivers to use ->cable_detect method. While at it: * Factor out cable detection to separate functions (if not already done). * hpt366.c/it8213.c/slc90e66.c: - don't check cable type if "idex=ata66" is used * pdc202xx_new.c: - add __devinit tag to pdcnew_cable_detect() * pdc202xx_old.c: - rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect() - add __devinit tag to pdc2026x_old_cable_detect() Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02ide: add struct ide_port_info instances to legacy host driversBartlomiej Zolnierkiewicz
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma(). * Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version. * Add 'const struct ide_port_info *d' argument to ide_device_add[_all](). * Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(), move it to ide-probe.c and call it in in ide_device_add_all() instead of ide_pci_setup_ports(). * Move ->mate setup to ide_device_add_all() from ide_port_init(). * Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable ->autotune currently. * Setup hwif->chipset in ide_init_port() but iff pi->chipset is set (to not override setup done by ide_hwif_configure()). * Add ETRAX host handling to ide_device_add_all(). * cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n. * pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks setup to pmac_ide_setup_device(). * Add 'struct ide_port_info' instances to legacy host drivers, pass them to ide_device_add() calls and then remove open-coded ports initialization. Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02atiixp/cs5535/scc_pata: fix "idex=ata66" parameter handlingBartlomiej Zolnierkiewicz
Don't override the cable type if the "idex=ata66" parameter was used. While at it: * atiixp.c: factor out cable detection to atiixp_cable_detect() from init_hwif_atiixp(). * cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to cs5535_cable_detect(). * scc_pata.c: factor out cable detection to scc_cable_detect() from init_hwif_scc() and remove incorrect comment. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits) PCI: make pci_bus a struct device PCI: fix codingstyle issues in include/linux/pci.h PCI: fix codingstyle issues in drivers/pci/pci.h PCI: PCIE ASPM support PCI: Fix fakephp deadlock PCI: modify SB700 SATA MSI quirk PCI: Run ACPI _OSC method on root bridges only PCI ACPI: AER driver should only register PCIe devices with _OSC PCI ACPI: Added a function to register _OSC with only PCIe devices. PCI: constify function pointer tables PCI: Convert drivers/pci/proc.c to use unlocked_ioctl pciehp: block new requests from the device before power off pciehp: workaround against Bad DLLP during power off pciehp: wait for 1000ms before LED operation after power off PCI: Remove pci_enable_device_bars() from documentation PCI: Remove pci_enable_device_bars() PCI: Remove users of pci_enable_device_bars() PCI: Add pci_enable_device_{io,mem} intefaces PCI: avoid save the same type of cap multiple times PCI: correctly initialize a structure for pcie_save_pcix_state() ...
2008-02-01PCI: Remove users of pci_enable_device_bars()Benjamin Herrenschmidt
This patch converts users of pci_enable_device_bars() to the new pci_enable_device_{io,mem} interface. The new API fits nicely, except maybe for the QLA case where a bit of code re-organization might be a good idea but I prefer sticking to the simple patch as I don't have hardware to test on. I'll also need some feedback on the cs5520 change. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01ide: make probe_hwif() return an error valueBartlomiej Zolnierkiewicz
Make probe_hwif() return an error value. While at it: * Remove comment about MAX_DRIVES == 2 limitation (it is not special to probe_hwif(), it is a general assumption taken by a lot of IDE code). * Rename probe_hwif() to ide_probe_port(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01ide: delete filenames/versions from commentsBartlomiej Zolnierkiewicz
Delete filenames/versions from comments. I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s to maintainers of the respective drivers. While at it: * Remove unused VERSION define from ide.c. * Remove unused/stale DRV_VERSION define from au1xxx-ide.c. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01ide: keep pointer to struct device instead of struct pci_dev in ide_hwif_tBartlomiej Zolnierkiewicz
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t. While on it: * Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce(). There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01ide: use ide_destroy_dmatable() instead of pci_unmap_sg() (take 2)Bartlomiej Zolnierkiewicz
Use ide_destroy_dmatable() in: * ide-dma.c::ide_build_dmatable() * sgiioc4.c::sgiioc4_build_dma_table() * pmac.c::pmac_ide_{build,destroy}_dmatable() There should be no functionality changes caused by this patch. v2: * pmac.c build fix from Andrew Morton. Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01piix: remove stale commentsBartlomiej Zolnierkiewicz
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01ide: add IDE_HFLAG_NO_DSC host flagBartlomiej Zolnierkiewicz
* Add IDE_HFLAG_NO_DSC host flag for hosts that doesn't support DSC overlap. * Set it in aec62xx (for ATP850UF only) and hpt34x host drivers. * Convert ide-tape device driver to check for IDE_HFLAG_NO_DSC flag. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01ide: add IDE_HFLAG_CLEAR_SIMPLEX host flagBartlomiej Zolnierkiewicz
* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base(). * Factor out code for forcing host out of "simplex" mode from ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper. * Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229), amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and serverworks (for CSB5) host drivers. * Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag instead of checking dev->device (BTW the code was buggy because it didn't check for dev->vendor, luckily none of these PCI Device IDs was used by some other vendor for PCI IDE controller). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01amd74xx: remove amd_ide_chips tableBartlomiej Zolnierkiewicz
* Remove no longer needed assertion from amd74xx_probe(). * Factor out cable detection for AMD7409 to amd7409_cable_detect() and for chipsets >= AMD7411 to amd7411_cable_detect(). * Use dev->vendor and dev->device instead of amd_config->udma_mask when selecting cable detection method and checking for broken FIFO support in init_chipset_amd74xx(). * Remove no longer needed AMD_BAD_FIFO define. * Add 'swdma' parameter for setting .swdma_mask to DECLARE_AMD_DEV() macro. * Add 'udma' parameter for setting .udma_mask to DECLARE_{AMD,NV}_DEV() macro. * Keep a copy of a current amd74xx_chipsets[] entry in amd74xx_probe() in order to fix ->swdma_mask on early AMD7409 revisions and ->udma_mask on Serenade mainboards. * Remove no longer needed fixups from init_chipset_amd74xx() and AMD_CHECK_{SWDMA,SERENADE} defines. * Move printing banner message from init_chipset_amd74xx() to amd74xx_probe(), also remove incorrect comment while at it. * Use hwif->ultra_mask instead of amd_config->udma_mask in amd_set_drive(). * Add 'udma_mask' argument to amd_set_speed() and pass UDMA mask from amd_set_drive() instead of using amd_config->udma_mask. * Move amd_config->base from AMD_* defines to users of these defines and add 0x40 the defined values. Then add amd_offset() inline helper for selecting offset from 0x40 base (needed for nVidia controllers) and finally use it in amd_set_speed(), amd7411_cable_detect() and init_chipset_amd74xx() instead of amd_config->base. * Remove no longer needed AMD_BAD_SWDMA define, ->{swdma,ultra}_mask setup from init_hwif_amd74xx(), amd_{config,chipset} variables and amd_ide_chips table. * Fix init_chipset_amd74xx() comment. * Bump driver version. There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01ide: ide_setup_dma() assumes 8 portsSergei Shtylyov
According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must always register 8 DMA ports with ide_setup_dma(), so its last argument is not needed. While at it, kill some useless parens in that function... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01trm290: cannot call ide_setup_dma()Sergei Shtylyov
The TRM-290 chip is *not* SFF-8038i compatible and therefore can *not* call ide_setup_dma() -- fix this and also cleanup the code a bit... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26cmd64x: remove /proc/ide/cmd64xBartlomiej Zolnierkiewicz
This belongs to user-space (and only if really needed). text data bss dec hex filename 3874 180 28 4082 ff2 drivers/ide/pci/cmd64x.o.before 2231 180 0 2411 96b drivers/ide/pci/cmd64x.o.after Additionaly to being bloat the code reported incorrect UDMA modes for the reserved values of UDIDETCR0/1 registers. Also while at it remove unused CNTRL_DIS_RA0/1 defines. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: make remaining built-in only IDE host drivers modular (take 2)Bartlomiej Zolnierkiewicz
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c file for probing PCI host drivers registered with IDE core (special case for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of the ordering in which all IDE host drivers are probed when IDE is built-in during link time. * Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific). * Move probing of ide-cris (cris arch specific) host driver before cmd640 (x86 arch specific). * Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300 (h8300 arch specific). * Add "probe_vlb" kernel parameter to cmd640 host driver and update Documentation/ide.txt accordingly. * Make IDE_ARM config option visible so it can also be disabled if needed. * Remove bogus comment from ide.c while at it. v2: * Fix two issues spotted by Sergei: - replace ENOMEM error value by ENOENT in ide-h8300 host driver - fix MODULE_PARM_DESC() in cmd640 host driver Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Mikael Starvik <starvik@axis.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: fix host drivers depending on ide_generic to probe for interfaces (take 2)Bartlomiej Zolnierkiewicz
* Add mpc8xx_ide_probe() to mpc8xx.c and call it from probe_for_hwifs(). * Convert ide_arm, ide-cris, ide-h8300, ide-pnp, buddha, falconide, gayle, macide, q40ide, cmd640 and mpc8xx host drivers to use ide_device_add(). This removes dependency on ide_generic for these drivers so update ide/Kconfig accordingly. v2: * ide_arm build fix (s/ide_device_idx/ide_device_add/) (Thanks to Christoph Lameter <clameter@sgi.com> for reporting the problem). Cc: Mikael Starvik <starvik@axis.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: drop 'initializing' argument from ide_register_hw()Bartlomiej Zolnierkiewicz
* Rename init_hwif_data() to ide_init_port_data() and export it. * For all users of ide_register_hw() with 'initializing' argument set hwif->present and hwif->hold are always zero so convert these host drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw() instead (also no need for init_hwif_default() call since the setup done by it gets over-ridden by ide_init_port_hw() call). * Drop 'initializing' argument from ide_register_hw(). Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: add ide_init_port_hw() helperBartlomiej Zolnierkiewicz
* Add ide_init_port_hw() helper. * rapide.c: convert rapide_locate_hwif() to rapide_setup_ports() and use ide_init_port_hw(). * ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports() and use ide_init_port_hw(). * sgiioc4.c: use ide_init_port_hw(). * pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(), setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw() in pmac_ide_setup_device(). This patch is a preparation for the future changes in the IDE probing code. There should be no functionality changes caused by this patch. Cc: Russell King <rmk@arm.linux.org.uk> Cc: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Jeremy Higdon <jeremy@sgi.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26sgiioc4: always init hwif->io_portsBartlomiej Zolnierkiewicz
'if (hwif->io_ports[IDE_DATA_OFFSET] != cmd_base)' is always true. Cc: Jeremy Higdon <jeremy@sgi.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: merge ->fixup and ->quirkproc methodsBartlomiej Zolnierkiewicz
* Assign drive->quirk_list in ->quirkproc implementations: - hpt366.c::hpt3xx_quirkproc() - pdc202xx_new.c::pdcnew_quirkproc() - pdc202xx_old.c::pdc202xx_quirkproc() * Make ->quirkproc void. * Move calling ->quirkproc from do_identify() to probe_hwif(). * Convert it821x_fixups() to it821x_quirkproc() in it821x.c. * Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove no longer needed drive->present check from is_dev_seagate_sata(). * Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif' as an argument. Then convert ide_register_hw() to accept 'quirkproc' argument instead of 'fixup' one. * Remove no longer needed ->fixup method. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: merge ->dma_host_{on,off} methods into ->dma_host_set methodBartlomiej Zolnierkiewicz
Merge ->dma_host_{on,off} methods into ->dma_host_set method which takes 'int on' argument. There should be no functionality changes caused by this patch. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: move drive->using_dma check to callers of ->dma_host_on methodBartlomiej Zolnierkiewicz
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26atiixp: remove ->dma_host_on and ->dma_host_off methodsBartlomiej Zolnierkiewicz
* Enable/disable UDMA in atiixp_set_dma_mode(). * Remove no longer needed atiixp_dma_host_{on,off}() and save_mdma_mode[]. * Bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: remove ->ide_dma_on and ->dma_off_quietly methods from ide_hwif_tBartlomiej Zolnierkiewicz
* Make ide_dma_off_quietly() and __ide_dma_on() always available. * Drop "__" prefix from __ide_dma_on(). * Check for presence of ->dma_host_on instead of ->ide_dma_on. * Convert all users of ->ide_dma_on and ->dma_off_quietly methods to use ide_dma_on() and ide_dma_off_quietly() instead. * Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods from ide_hwif_t. * Make ide_dma_on() void. There should be no functionality changes caused by this patch. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26sgiioc4: add ide_toggle_bounce() callsBartlomiej Zolnierkiewicz
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly methods so they match generic __ide_dma_on()/ide_dma_off_quietly(). Tested on Altix by Jeremy. Acked-by: Jeremy Higdon <jeremy@sgi.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26cy82c693: add ->set_dma_mode methodBartlomiej Zolnierkiewicz
* Fix SWDMA/MWDMA masks in cy82c693_chipset. * Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to check whether the DMA should be enabled even if ide_max_dma_mode() fails. * Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode() and remove no longer needed cy82c693_ide_dma_on(). Then set IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in cy82c693_chipset. * Bump driver version. As a result of this patch cy82c693 driver will configure and use DMA on all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26cy82c693: correct DMA modes clippingBartlomiej Zolnierkiewicz
* Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on(). * Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable(): - id->tDMA may not be defined on newer devices - id->vendor6/id->tDMA word is in LE endianness (cy82c693 seems to be Alpha specific though) * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26ide: (hopefully) fix VDMA for CS5520Bartlomiej Zolnierkiewicz
* Set the correct hwif->dma_base for the second channel in ide_get_or_set_dma_base(). * Remove DMA enable code from cs5520_set_pio_mode(), this can be handled by the generic ->dma_host_on method now. * Add VDMA check to ide_config_drive_speed(). * drive->using_dma was never enabled since cs5520 host driver's ->ide_dma_on method overrided the generic ->ide_dma_on (so __ide_dma_on() was never called, drive->using_dma was never set and VDMA was never used since it depends on drive->using_dma). Fix it by using ->dma_host_on method instead of ->ide_dma_on (also add matching ->dma_host_off method). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26serverworks: cleanup ->set_dma_mode methodBartlomiej Zolnierkiewicz
IDE core guarantees that ->set_dma_mode will be called only for DMA modes set in SWDMA/MWDMA/UDMA masks. There should be no functionality changes caused by this patch. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26sl82c105: remove no longer needed ->selectproc methodBartlomiej Zolnierkiewicz
* Program register 0x40 in sl82c105_resetproc(). * Remove no longer needed sl82c105_selectproc() and pci_set_drvdata() calls. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26sl82c105: program DMA/PIO timings in ->dma_start/->ide_dma_endBartlomiej Zolnierkiewicz
* Program DMA timings in sl82c105_dma_start() (->dma_start method) before starting DMA transfer. * Add sl82c105_dma_end() (->ide_dma_end method) to switch back to PIO timings when DMA transfer is complete. * In sl82c105_set_pio_mode() program timings regardless of ->using_dma setting and in sl82c105_set_dma_mode() only cache the new timings. * Remove no longer needed sl82c105_{ide_dma_on,off_quietly}(). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25sc1200: move DMA timings to timing tablesBartlomiej Zolnierkiewicz
Based on pata_sc1200.c. There should be no functionality changes caused by this patch. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-02 16:05:54 +0000