| Age | Commit message (Collapse) | Author |
|---|
|
->ide_dma_on method is called only after successful ide_dma_check() call
(ide_dma_check()->ide_tune_dma() checks DMA blacklist) or if drive->using_dma
has been previously enabled for a given device (->ide_dma_on is the only place
which sets drive->using_dma to '1').
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* ->dma_off_quietly is always called before ide_set_dma()
so the call can be moved inside ide_set_dma().
* ide_dma_check() doesn't touch hardware so ->dma_off_quietly
call for 'rc == -1' case is redundant, remove it.
* '0' and '-1' are the only values returned by ide_dma_check()
so remove dead code for other cases.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
ide_set_dma() calls ->ide_dma_on method itself and returns zero
only if ->ide_dma_on call succeeded.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on pata_sc1200.c.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().
* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
(aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
methods in host drivers that don't (IDE core code guarantees that
->set_dma_mode will be called only for modes which are present
in SWDMA/MWDMA/UDMA masks).
While at it:
* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
hpt34x/hpt366/pdc202xx_old/serverworks host driver.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out UDMA programming code from sis_set_dma_mode() to per
chipset family helpers: sis_{ata33,ata133}_program_udma_timings().
* Add sis_program_udma_timings() helper.
* Remove unneeded casts to 'unsigned long'.
* Minor cleanups.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move PIO programming code from pdcnew_set_mode() to pdcnew_set_pio_mode().
* Rename pdcnew_set_mode() to pdcnew_set_dma_mode().
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move the common code from ide_dump_{ata,atapi}_status() to
ide_dump_status().
* ide_dump_{ata,atapi}_status() -> ide_dump_{ata,atapi}_error().
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Export ide_get_lba_addr().
* Convert idedisk_{read_native,set}_max_address() to use ide_get_lba_addr().
* Remove incorrect comment from idedisk_read_native_max_address()
(noticed by Sergei).
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
power4:
drivers/ide/ide-lib.c: In function `ide_dump_sector':
drivers/ide/ide-lib.c:516: warning: long long unsigned int format, u64 arg (arg 2)
We don't know what type is used to implement u64 hence it must always be cast
when printed.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out code reading taskfile registers from ide_end_drive_cmd()
to the new ide_tf_read() helper.
* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
particular IDE taskfile register in ide_tf_read().
* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.
* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.
* Factor out code getting sector address from ide_dump_ata_status()
to the new ide_dump_sector() function.
* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().
* Remove no longer needed ide_read_24().
The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix registers loading order in ide_dump_ata_status()/ide_read_24().
Load registers in this order:
* IDE_SECTOR_REG
* IDE_LCYL_REG
* IDE_HCYL_REG
* IDE_SELECT_REG
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_DMA_PIO_FALLBACK taskfile flag to indicate the need
to skip loading taskfile registers in do_rw_taskfile().
* Export do_rw_taskfile().
* Convert __ide_do_rw_disk() to use do_rw_taskfile().
* Unexport ide_tf_load().
* Unexport {pre_task_out,task_in}_intr() and make it static.
* Remove incorrect comment about do_rw_taskfile() from <linux/ide.h>.
There should be no functionality changes caused by this patch.
v2:
* Add missing blk_fs_request() check to task_dma_ok() (for VDMA).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ide_tf_set_cmd() helper for selecting/setting command and data phase
(note: DMA data phases are there for completness, they are not required ATM).
* Set IDE_TFLAG_WRITE taskfile flag for write requests in __ide_do_rw_disk().
* Convert __ide_do_rw_disk() to use the new ide_tf_set_cmd() helper.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
s/WAIT_CMD/WAIT_WORSTCASE/ to make the timeout the same as in do_rw_taskfile()
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_CUSTOM_HANDLER taskfile flag and use it for internal requests
which require custom handlers. Check the flag in do_rw_taskfile() and set
handler accordingly.
* Cleanup ide_init_{specify,restore,setmult}_cmd() and rename it to
ide_tf_set_{specify,restore,setmult}_cmd().
* Make {set_geometry,recal,set_multmode}_intr() static.
* Remove no longer needed 'handler' field from ide_task_t.
v2:
* 'handler' in do_rw_taskfile() must be set to NULL initially.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use ->data_phase to set ->handler in do_rw_taskfile() instead of
setting ->handler in callers of ide_raw_taskfile()/do_rw_taskfile().
* Unexport task_no_data_intr() and make it static.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use task->data_phase in do_rw_taskfile() to decide what to do.
* task->prehandler is only used by TASKFILE[_MULTI]_OUT so just
use pre_task_out_intr() directly and remove no longer needed
'prehandler' field from ide_task_t.
* Remove no longer needed ide_pre_handler_t type.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
task->data_phase == TASKFILE_MULTI_{IN,OUT} vs drive->mult_count == 0
check is needed also for ide_taskfile_ioctl() requests that don't have
IDE_TFLAG_FLAGGED taskfile flag set.
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix __ide_do_rw_disk() to use ->OUTBSYNC instead of ->OUTB
(needed for pmac and scc_pata host drivers).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Save PCI regs values for both IDE ports in one buffer, in order to eliminate
a needless and ugly loop across all hwifs, searching for our PCI device.
Partially based on the previous patch by Jeff Garzik.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_IN_DATA taskfile flag to indicate the need of reading
IDE_DATA_REG in ide_end_drive_cmd().
Set the new flag in ide_taskfile_ioctl() if ->in_flags.b.data is set.
* Add IDE_TFLAG_FLAGGED_SET_IN_FLAGS taskfile flag to indicate the
need of modifying ->in_flags in ide_taskfile_ioctl().
Set the new flag in flagged_taskfile() and move the code modifying
->tf_in_flags to ide_taskfile_ioctl().
While at it remove the bogus comment: ->tf_in_flags (except .b.data)
have no effect on selection of registers to read.
* Remove no longer needed 'tf_in_flags' field from ide_task_t.
As the result we finally have the internals of HDIO_DRIVE_TASKFILE ioctl
separated from the core IDE code.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add 'data_buf' and 'nsect' variables in ide_taskfile_ioctl()
to cache data buffer pointer and number of sectors to transfer
(this allows us to have only one ide_diag_taskfile() call).
* Add IDE_TFLAG_WRITE taskfile flag and use it to check whether
the REQ_RW request flag should be set.
* Move ->command_type handling from ide_diag_taskfile() to
ide_taskfile_ioctl() and use ->req_cmd instead of ->command_type.
* Add 'nsect' parameter to ide_raw_taskfile().
* Merge ide_diag_taskfile() into ide_raw_taskfile().
* Initialize ->data_phase explicitly in idedisk_prepare_flush(),
ide_start_power_step() and ide_disk_special().
* Remove no longer needed 'command_type' field from ide_task_t.
* Add #ifndef/#endif __KERNEL__ to <linux/hdreg.h> around no
longer used by kernel IDE_DRIVE_TASK_* and TASKFILE_* defines.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Given that:
* hpt366.c::hpt3xx_intrproc() is the only user of hwif->intrproc
* hpt366.c::hpt3xx_quirkproc() sets drive->quirk_list to 1 for quirky drives
which is a value unique to hpt366 host driver
we can remove hwif->intproc and just check for drive->quirk_list == 1
in ide_do_request().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_pktcmd_tf_load() helper and convert ATAPI device drivers to use it.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Load IDE_BCOUNTL_REG before IDE_BCOUNTH_REG when issuing packet command.
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Load IDE_CONTROL_REG before other registers in cdrom_start_packet_command().
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
While at it move misplaced FIXME comment in the right place.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove atapi_ireason_t.
While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)
v2:
* v1 had CD and IO bits reversed in many places.
* Use CD and IO defines from <linux/hdreg.h>.
v3:
* Fix incorrect "(ireason & IO) == test_bit()". (Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove ata_nsector_t, ata_data_t (unused) and atapi_bcount_t.
While at it:
* replace 'HWIF(drive)' by 'hwif'
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove atapi_feature_t.
While at it:
* replace 'HWIF(drive)' by 'hwif'
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove atapi_error_t.
While at it:
* replace 'HWIF(drive)' by 'drive->hwif'
v2:
* Add {ILI,EOM,LFS}_ERR defines to <linux/hdreg.h>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove ata_status_t (unused) and atapi_status_t.
While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Extend timeout for REQ_TYPE_ATA_{CMD,TASK} requests from WAIT_CMD (10sec)
to WAIT_WORSTCASE (30sec, already used for REQ_TYPE_ATA_TASKFILE).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Set taskfile flags for REQ_TYPE_ATA_TASKFILE requests before
adding the request to the queue.
* Cleanup execute_drive_cmd().
* Remove unnecessary writes to HOB taskfile registers when using
LBA48 disk for the following cases:
- Power Management requests
(WIN_FLUSH_CACHE[_EXT], WIN_STANDBYNOW1, WIN_IDLEIMMEDIATE commands)
- special commands (WIN_SPECIFY, WIN_RESTORE, WIN_SETMULT)
- Host Protected Area support (WIN_READ_NATIVE_MAX, WIN_SET_MAX)
- /proc/ide/ SMART support (WIN_SMART with SMART_ENABLE,
SMART_READ_VALUES and SMART_READ_THRESHOLDS subcommands)
- write cache enabling/disabling in ide-disk
(WIN_SETFEATURES with SETFEATURES_{EN,DIS}_WCACHE)
- write cache flushing in ide-disk (WIN_FLUSH_CACHE[_EXT])
- acoustic management in ide-disk
(WIN_SETFEATURES with SETFEATURES_{EN,DIS}_AAM)
- door (un)locking in ide-disk (WIN_DOORLOCK, WIN_DOORUNLOCK)
- /proc/ide/hd?/identify support (WIN_IDENTIFY)
- ACPI _GTF taskfiles
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use IDE_TFLAG_LBA48 for REQ_TYPE_ATA_TASKFILE requests in ide_end_drive_cmd()
to decide whether we need to read HOB taskfile registers.
* Update execute_drive_cmd() accordingly.
This is a preparation for the next patch which removes unnecessary writes to
HOB taskfile registers for some ATA commands.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_OUT_DEVICE taskfile flag to indicate the need of writing
the Device register and handle it in ide_tf_load().
Update ide_tf_load() and {do_rw,flagged}_taskfile() users accordingly.
* Use struct ide_taskfile and ide_tf_load() in execute_drive_cmd().
* Make the debugging code dump all taskfile registers for both
REQ_ATA_TYPE_{CMD,TASK} requests and move it to ide_tf_load()
so it also covers REQ_ATA_TYPE_TASKFILE requests.
There should be no functionality changes caused by this patch
(unless DEBUG is defined).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remove ide_cmd() helper.
* Clear nIEN and call SELECT_MASK() before writing taskfile registers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename 'args' variable in 'if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE)'
block to 'task'.
* execute_drive_cmd() is used only for REQ_TYPE_ATA_{CMD,TASK,TASKFILE} so
we can move the common code out from 'if (rq->cmd_type == REQ_TYPE_ATA_CMD)'
and 'if (rq->cmd_type == REQ_TYPE_ATA_TASK)' blocks.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Move loading of IDE_NSECTOR_REG from ide_cmd() to execute_drive_cmd()
(load the IDE_NSECTOR_REG just after IDE_FEATURE_REG).
This also allows us to drop 'nsect' argument from ide_cmd() and simplify
execute_drive_cmd() code for REQ_TYPE_ATA_CMD case a bit.
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix registers loading order for REQ_TYPE_ATA_CMD request with WIN_SMART
command in execute_drive_cmd() (load IDE_FEATURE_REG and IDE_SECTOR_REG
before loading IDE_LCYL_REG and IDE_HCYL_REG).
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove stale ide.h "configuration options":
* INITIAL_MULT_COUNT - always defined to 0
* SUPPORT_SLOW_DATA_PORTS - unused
* OK_TO_RESET_CONTROLLER - always defined to 1
* DISABLE_IRQ_NOSYNC - always defined to 0
Leave SUPPORT_VLB_SYNC (defined to 0 for CRIS and FRV, otherwise to 1)
for now but disallow overriding it by <asm/ide.h>.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
We can safely remove CONFIG_IDEPCI_SHARE_IRQ and always support
PCI IRQ sharing.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
