| Age | Commit message (Collapse) | Author |
|---|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
|
|
The IB CM should include the HCA ACK delay when calculating the local
ACK timeout value to use for RC QPs. If the HCA ACK delay is large
enough relative to the packet life time, then if it is not taken into
account, the calculated timeout value ends up being too small, which
can result in "retry exceeded" errors.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
InfiniBand HCAs replicate multicast packets back to the QP that sent
them if that QP is attached to the destination multicast group. This
means that IPoIB multicasts are often replicated back to the receive
queue of the interface that generated them. To avoid confusing the
network stack, we drop these duplicates within the IPoIB driver.
However, there's no reason to free the skb that received the duplicate
and then immediately allocate a new skb to post to the receive queue.
We can be more efficient and just repost the same skb.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix
drivers/infiniband/ulp/ipoib/ipoib_cm.c:1151: warning: unused variable 'dev'
by getting rid of the variable dev, which is only used if CONFIG_IPV6
is enabled, and replacing the one use of it with the value it is
assigned, namely priv->dev.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
If a page can't be allocated for the frag list of a skb, the code to
unmap the partially allocated list is off by one. For exaple, if
'frags' equals one, i == 0, and the alloc_page() fails, then the old
loop would have unmapped mapping[1] which is uninitialized. The same
would happen if the call to ib_dma_map_page() failed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
It's completely unused.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
IPoIB connected mode currently rejects a connection request unless the
supported MTU is >= the local netdevice MTU. This breaks
interoperability with implementations that might have tweaked
IPOIB_CM_MTU, and there's real no longer a reason to do so: this test
is just a leftover from when we did not tweak MTU per-connection. Fix
this by making the test as permissive as possible.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix a crasher bug in IPoIB CM: once a QP is in the RTR state, a
receive completion (or even an asynchronous error) might be observed
on this QP, so we have to initialize all of our receive data
structures before moving to the RTR state.
As an optimization (since modify_qp might take a long time), the
jiffies update done when moving RX to the passive_ids list is also
left in place to reduce the chance of the RX being misdetected as
stale.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=662>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
iscsi_iser: convert to use the data buffer accessors
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
TODO: use scsi_for_each_sg().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.
This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
- Remove shadow of request length from struct iscsi_cmd_task.
- change all users to use scsi_cmnd->request_bufflen directly
(With bidi we will use scsi-ml API to retrieve in/out length)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.
For hw iscsi, it is nice to see what the card is using.
This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
iscsid and udev need to key off the hw address being
used so add some helpers for iser and iscsi tcp.
Also convert them
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
commit 518b1646 ("IPoIB/cm: Fix SRQ WR leak") introduced a severe
performance regression on Mellanox cards, because keeping a QP in the
error state for extended periods of time moves hardware to the slow
path (until the QP is destroyed). For example, MPI latency goes from
~3 usecs to ~7 usecs.
Fix this by posting a send WR on one of the QPs that are being
flushed, instead of using a separate drain QP that is kept in the
error state.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=636>,
reported and bisected by Scott Weitzenkamp at Cisco and debugged by
Sasha Mikheev at Voltaire.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Since NAPI polling is disabled while ipoib_cm_dev_stop() is running,
ipoib_cm_dev_stop() must poll the CQ itself in order to see the
packets draining.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
time_after() was used backwards, so the timeout occurred immediately.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
SRQ WR leakage has been observed with IPoIB/CM: e.g. flipping ports on
and off will, with time, leak out all WRs and then all connections
will start getting RNR NAKs. Fix this in the way suggested by spec:
move the QP being destroyed to the error state, wait for "Last WQE
Reached" event and then post WR on a "drain QP" connected to the same
CQ. Once we observe a completion on the drain QP, it's safe to call
ib_destroy_qp.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Trivial error message fixups.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
SM reconfiguration or failover possibly causes a shuffling of the values
in the P_Key table. Right now, IPoIB only queries for the P_Key index
once when it creates the device QP, and hence there are problems if the
index of a P_Key value changes. Fix this by using the PKEY_CHANGE event
to trigger a recheck of the P_Key index.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
In the presence of some running RX connections, we repeat
queue_delayed_work calls each 4 RX WRs, which is a waste. It's enough
to start stale task when a first passive connection is added, and
rerun it every IPOIB_CM_RX_DELAY as long as there are outstanding
passive connections.
This removes some code from RX data path.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
|
|
Convert the IP-over-InfiniBand network device driver over to using
NAPI to handle completions for the main CQ. This covers all receives
as well as datagram mode sends; send completions for connected mode
connections are still handled from interrupt context.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add an orig_dgid attribute in sysfs for SRP scsi_hosts, so that
userspace can tell what the original dgid value written to the
add_target file was, even if the connection is redirected to a
different port while connecting.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The IPoIB CM spec allows the use of a single connection in both
active->passive and passive->active directions. The current Linux
code uses one connection for both directions, but if another node only
uses one connection for both directions, we oops when we try to look
up the passive connection. Fix by checking that qp_context is
non-NULL before dereferencing it.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (87 commits)
[SCSI] fusion: fix domain validation loops
[SCSI] qla2xxx: fix regression on sparc64
[SCSI] modalias for scsi devices
[SCSI] sg: cap reserved_size values at max_sectors
[SCSI] BusLogic: stop using check_region
[SCSI] tgt: fix rdma transfer bugs
[SCSI] aacraid: fix aacraid not finding device
[SCSI] aacraid: Correct SMC products in aacraid.txt
[SCSI] scsi_error.c: Add EH Start Unit retry
[SCSI] aacraid: [Fastboot] Panics for AACRAID driver during 'insmod' for kexec test.
[SCSI] ipr: Driver version to 2.3.2
[SCSI] ipr: Faster sg list fetch
[SCSI] ipr: Return better qc_issue errors
[SCSI] ipr: Disrupt device error
[SCSI] ipr: Improve async error logging level control
[SCSI] ipr: PCI unblock config access fix
[SCSI] ipr: Fix for oops following SATA request sense
[SCSI] ipr: Log error for SAS dual path switch
[SCSI] ipr: Enable logging of debug error data for all devices
[SCSI] ipr: Add new PCI-E IDs to device table
...
|
|
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If skb allocation fails when we start the device, we call
ipoib_cm_dev_stop() even though ipoib_cm_dev_open() did not run to
completion, so we pass an invalid pointer to ib_destroy_cm_id and get
an oops.
Fix by clearing cm.id on error, and testing it in cm_dev_stop().
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=561>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (49 commits)
IB: Set class_dev->dev in core for nice device symlink
IB/ehca: Implement modify_port
IB/umad: Clarify documentation of transaction ID
IPoIB/cm: spin_lock_irqsave() -> spin_lock_irq() replacements
IB/mad: Change SMI to use enums rather than magic return codes
IB/umad: Implement GRH handling for sent/received MADs
IB/ipoib: Use ib_init_ah_from_path to initialize ah_attr
IB/sa: Set src_path_bits correctly in ib_init_ah_from_path()
IB/ucm: Simplify ib_ucm_event()
RDMA/ucma: Simplify ucma_get_event()
IB/mthca: Simplify CQ cleaning in mthca_free_qp()
IB/mthca: Fix mthca_write_mtt() on HCAs with hidden memory
IB/mthca: Update HCA firmware revisions
IB/ipath: Fix WC format drift between user and kernel space
IB/ipath: Check that a UD work request's address handle is valid
IB/ipath: Remove duplicate stuff from ipath_verbs.h
IB/ipath: Check reserved memory keys
IB/ipath: Fix unit selection when all CPU affinity bits set
IB/ipath: Don't allow QPs 0 and 1 to be opened multiple times
IB/ipath: Disable IB link earlier in shutdown sequence
...
|
|
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are quite a few places in ipoib_cm.c where we know IRQs are
enabled because we do something that sleeps in the same function, so
we can convert several occurrences of spin_lock_irqsave() to a plain
spin_lock_irq(). This cleans up the source a little and makes the
code smaller too:
add/remove: 0/0 grow/shrink: 1/5 up/down: 3/-51 (-48)
function old new delta
ipoib_cm_tx_reap 403 406 +3
ipoib_cm_stale_task 146 145 -1
ipoib_cm_dev_stop 173 172 -1
ipoib_cm_tx_handler 964 956 -8
ipoib_cm_rx_handler 956 937 -19
ipoib_cm_skb_reap 212 190 -22
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
To support destinations that are not on the local IB subnet, IPoIB
should include the GRH information when constructing an address
handle. Using the existing ib_init_ah_from_path() call will do this
for us.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
|
|
There's no point in printing the opcode field in the completion
handling debugging output, since the type of completion is already
printed at the beginning of the line. In fact the opcode field is not
even defined for completions with a status other than success.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Receive buffers need to be mapped with DMA_FROM_DEVICE. Incorrectly
mapping with DMA_TO_DEVICE causes a hard lock on ppc64 machines with
an IOMMU.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=431>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When a connection is terminated asynchronously from the iSCSI layer's
perspective, iSER needs to notify the iSCSI layer that the connection
has failed. This is done using a workqueue (switched to from the iSER
tasklet context). Meanwhile, the connection object (that holds the
work struct) is released. If the workqueue function wasn't called
yet, it will be called later with a NULL pointer, which will crash the
kernel.
The context switch (tasklet to workqueue) is not required, and
everything can be done from the iSER tasklet. This eliminates the NULL
work struct bug (and simplifies the code).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Handle aborting a command after it is sent
IB/mthca: Fix thinko in init_mr_table()
RDMA/cxgb3: Fix resource leak in cxio_hal_init_ctrl_qp()
|
|
The SCSI midlayer may abort a command that was already sent. If the
initiator is still trying to send the command (or data-out PDUs for
that command), the QP may time out after the midlayer times
out. Therefore, when aborting the command, iSER may still have
references for the command's buffers. When sending these PDUs, the
sends will complete with an error and their resources will be released
then.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
->neigh_destructor() is killed (not used), replaced with
->neigh_cleanup(), which is called when neighbor entry goes to dead
state. At this point everything is still valid: neigh->dev,
neigh->parms etc.
The device should guarantee that dead neighbor entries (neigh->dead !=
0) do not get private part initialized, otherwise nobody will cleanup
it.
I think this is enough for ipoib which is the only user of this thing.
Initialization private part of neighbor entries happens in ipib
start_xmit routine, which is not reached when device is down. But it
would be better to add explicit test for neigh->dead in any case.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The packet length checks in ipoib are broken: we add 4 bytes (IPoIB
encapsulation header) when sending a packet, not 20 bytes (hardware
address length) to each packet. Therefore, if connected mode is
enabled so that the interface MTU is larger than the multicast MTU,
IPoIB may end up trying to send too-long multicast packets. For
example, multicast is broken if a message of size 2048 bytes is sent
on an interface with UD MTU 2048, because 2048 is bigger than the real
limit of 2044 but the code tests against the wrong limit of 2060.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=418>,
submitted by Scott Weitzenkamp <sweitzen@cisco.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The connected mode code added the possibility that an neigh struct
gets freed in the list_for_each_entry() loop in path_rec_completion(),
which causes a use-after-free. Fix this by changing to the _safe
variant of the list walking macro.
This was spotted by the Coverity checker (CID 1567).
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
There's a race between ipoib_mcast_leave() and ipoib_mcast_join_finish()
where we can try to detach from a multicast group before we've
attached to it. Fix this by reordering the code in ipoib_mcast_leave
to free the multicast group first, which waits for the multicast
callback thread (which calls ipoib_mcast_join_finish()) to complete
before detaching from the group.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The sense of the time_after_eq() test in ipoib_cm_stale_task() is
reversed so that only non-stale connections are reaped. Fix this by
changing to time_before_eq().
Noticed by Pradeep Satyanarayana <pradeep@us.ibm.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
