aboutsummaryrefslogtreecommitdiff
path: root/drivers/infiniband
AgeCommit message (Collapse)Author
2007-10-15IB/ipoib: Verify address handle validity on sendMoni Shoua
When the bonding device senses a carrier loss of its active slave it replaces that slave with a new one. In between the times when the carrier of an IPoIB device goes down and ipoib_neigh is destroyed, it is possible that the bonding driver will send a packet on a new slave that uses an old ipoib_neigh. This patch detects and prevents this from happenning. Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com> Acked-by: Roland Dreier <rdreier@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15IB/ipoib: Bound the net device to the ipoib_neigh structueMoni Shoua
IPoIB uses a two layer neighboring scheme, such that for each struct neighbour whose device is an ipoib one, there is a struct ipoib_neigh buddy which is created on demand at the tx flow by an ipoib_neigh_alloc(skb->dst->neighbour) call. When using the bonding driver, neighbours are created by the net stack on behalf of the bonding (master) device. On the tx flow the bonding code gets an skb such that skb->dev points to the master device, it changes this skb to point on the slave device and calls the slave hard_start_xmit function. Under this scheme, ipoib_neigh_destructor assumption that for each struct neighbour it gets, n->dev is an ipoib device and hence netdev_priv(n->dev) can be casted to struct ipoib_dev_priv is buggy. To fix it, this patch adds a dev field to struct ipoib_neigh which is used instead of the struct neighbour dev one, when n->dev->flags has the IFF_MASTER bit set. Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com> Acked-by: Roland Dreier <rdreier@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (207 commits) [SCSI] gdth: fix CONFIG_ISA build failure [SCSI] esp_scsi: remove __dev{init,exit} [SCSI] gdth: !use_sg cleanup and use of scsi accessors [SCSI] gdth: Move members from SCp to gdth_cmndinfo, stage 2 [SCSI] gdth: Setup proper per-command private data [SCSI] gdth: Remove gdth_ctr_tab[] [SCSI] gdth: switch to modern scsi host registration [SCSI] gdth: gdth_interrupt() gdth_get_status() & gdth_wait() fixes [SCSI] gdth: clean up host private data [SCSI] gdth: Remove virt hosts [SCSI] gdth: Reorder scsi_host_template intitializers [SCSI] gdth: kill gdth_{read,write}[bwl] wrappers [SCSI] gdth: Remove 2.4.x support, in-kernel changelog [SCSI] gdth: split out pci probing [SCSI] gdth: split out eisa probing [SCSI] gdth: split out isa probing gdth: Make one abuse of scsi_cmnd less obvious [SCSI] NCR5380: Use scsi_eh API for REQUEST_SENSE invocation [SCSI] usb storage: use scsi_eh API in REQUEST_SENSE execution [SCSI] scsi_error: Refactoring scsi_error to facilitate in synchronous REQUEST_SENSE ...
2007-10-12Driver core: change add_uevent_var to use a structKay Sievers
This changes the uevent buffer functions to use a struct instead of a long list of parameters. It does no longer require the caller to do the proper buffer termination and size accounting, which is currently wrong in some places. It fixes a known bug where parts of the uevent environment are overwritten because of wrong index calculations. Many thanks to Mathieu Desnoyers for finding bugs and improving the error handling. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12[SCSI] transport_srp: add rport roles attributeFUJITA Tomonori
This adds a 'roles' attribute to rport like transport_fc. The role can be initiator or target. That is, the initiator driver creates target remote ports and the target driver creates initiator remote ports. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12[SCSI] ib_srp: convert to use the srp transport classFUJITA Tomonori
This converts ib_srp to use the srp transport class. I don't have ib hardware so I've not tested this patch. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Roland Dreier <rolandd@cisco.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-11Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits) mlx4_core: Fix section mismatches IPoIB: Allow setting policy to ignore multicast groups IB/mthca: Mark error paths as unlikely() in post_srq_recv functions IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages. IB/ipath: Remove redundant link state checks IB/ipath: Fix IB_EVENT_PORT_ERR event IB/ipath: Better handling of unexpected GPIO interrupts IB/ipath: Maintain active time on all chips IB/ipath: Fix QHT7040 serial number check IB/ipath: Indicate a couple of chip bugs to userspace IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close IB/ipath: Remove duplicate copy of LMC IB/ipath: Add ability to set the LMC via the sysfs debugging interface IB/ipath: Optimize completion queue entry insertion and polling IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED IB/ipath: Generate flush CQE when QP is in error state IB/ipath: Remove redundant code IB/ipath: Future proof eeprom checksum code (contents reading) IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate ...
2007-10-10[INET]: local port range robustnessStephen Hemminger
Expansion of original idea from Denis V. Lunev <den@openvz.org> Add robustness and locking to the local_port_range sysctl. 1. Enforce that low < high when setting. 2. Use seqlock to ensure atomic update. The locking might seem like overkill, but there are cases where sysadmin might want to change value in the middle of a DoS attack. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10IPoIB: Fix unused variable warningRoland Dreier
The conversion to use netdevice internal stats left an unused variable in ipoib_neigh_free(), since there's no longer any reason to get netdev_priv() in order to increment dropped packets. Delete the unused priv variable. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10[IPoIB]: Convert to netdevice internal statsRoland Dreier
Use the stats member of struct netdevice in IPoIB, so we can save memory by deleting the stats member of struct ipoib_dev_priv, and save code by deleting ipoib_get_stats(). Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[NET]: Move hardware header operations out of netdevice.Stephen Hemminger
Since hardware header operations are part of the protocol class not the device instance, make them into a separate object and save memory. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[NET]: Nuke SET_MODULE_OWNER macro.Ralf Baechle
It's been a useless no-op for long enough in 2.6 so I figured it's time to remove it. The number of people that could object because they're maintaining unified 2.4 and 2.6 drivers is probably rather small. [ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ] Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[NET]: Make the device list and device lookups per namespace.Eric W. Biederman
This patch makes most of the generic device layer network namespace safe. This patch makes dev_base_head a network namespace variable, and then it picks up a few associated variables. The functions: dev_getbyhwaddr dev_getfirsthwbytype dev_get_by_flags dev_get_by_name __dev_get_by_name dev_get_by_index __dev_get_by_index dev_ioctl dev_ethtool dev_load wireless_process_ioctl were modified to take a network namespace argument, and deal with it. vlan_ioctl_set and brioctl_set were modified so their hooks will receive a network namespace argument. So basically anthing in the core of the network stack that was affected to by the change of dev_base was modified to handle multiple network namespaces. The rest of the network stack was simply modified to explicitly use &init_net the initial network namespace. This can be fixed when those components of the network stack are modified to handle multiple network namespaces. For now the ifindex generator is left global. Fundametally ifindex numbers are per namespace, or else we will have corner case problems with migration when we get that far. At the same time there are assumptions in the network stack that the ifindex of a network device won't change. Making the ifindex number global seems a good compromise until the network stack can cope with ifindex changes when you change namespaces, and the like. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[NET]: Make NAPI polling independent of struct net_device objects.Stephen Hemminger
Several devices have multiple independant RX queues per net device, and some have a single interrupt doorbell for several queues. In either case, it's easier to support layouts like that if the structure representing the poll is independant from the net device itself. The signature of the ->poll() call back goes from: int foo_poll(struct net_device *dev, int *budget) to int foo_poll(struct napi_struct *napi, int budget) The caller is returned the number of RX packets processed (or the number of "NAPI credits" consumed if you want to get abstract). The callee no longer messes around bumping dev->quota, *budget, etc. because that is all handled in the caller upon return. The napi_struct is to be embedded in the device driver private data structures. Furthermore, it is the driver's responsibility to disable all NAPI instances in it's ->stop() device close handler. Since the napi_struct is privatized into the driver's private data structures, only the driver knows how to get at all of the napi_struct instances it may have per-device. With lots of help and suggestions from Rusty Russell, Roland Dreier, Michael Chan, Jeff Garzik, and Jamal Hadi Salim. Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra, Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan. [ Ported to current tree and all drivers converted. Integrated Stephen's follow-on kerneldoc additions, and restored poll_list handling to the old style to fix mutual exclusion issues. -DaveM ] Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10IPoIB: Allow setting policy to ignore multicast groupsOr Gerlitz
The kernel IB stack allows (through the RDMA CM) userspace applications to join and use multicast groups from the IPoIB MGID range. This allows multicast traffic to be handled directly from userspace QPs, without going through the kernel stack, which gives better performance for some applications. However, to fully interoperate with IP multicast, such userspace applications need to participate in IGMP reports and queries, or else routers may not forward the multicast traffic to the system where the application is running. The simplest way to do this is to share the kernel IGMP implementation by using the IP_ADD_MEMBERSHIP option to join multicast groups that are being handled directly in userspace. However, in such cases, the actual multicast traffic should not also be handled by the IPoIB interface, because that would burn resources handling multicast packets that will just be discarded in the kernel. To handle this, this patch adds lookup on the database used for IB multicast group reference counting when IPoIB is joining multicast groups, and if a multicast group is already handled by user space, then the IPoIB kernel driver ignores the group. This is controlled by a per-interface policy flag. When the flag is set, IPoIB will not join and attach its QP to a multicast group which already has an entry in the database; when the flag is cleared, IPoIB will behave as before this change. For each IPoIB interface, the /sys/class/net/$intf/umcast attribute controls the policy flag. The default value is off/0. Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-10IB/mthca: Mark error paths as unlikely() in post_srq_recv functionsEli Cohen
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.Dave Olson
Fixed to be the same as everywhere else. copy and then zero the page * in the array first, and then pass the copy to the VM routines. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Remove redundant link state checksRalph Campbell
This patch removes some redundant checks when the SMA changes the link state since the same checks are made in the lower level function that sets the state. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Fix IB_EVENT_PORT_ERR eventRalph Campbell
The link state event calls were being generated when the SM told the SMA to change link states. This works for IB_EVENT_PORT_ACTIVE but not if the link goes down and stays down. The fix is to generate event calls from the interrupt handler when the HW link state changes. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Better handling of unexpected GPIO interruptsMichael Albaugh
The General Purpose I/O pins can be configured to cause interrupts. At the end of the interrupt code dealing with all known causes, a message is output if any bits remain un-handled. Since this is a "can't happen" scenario, it should only be triggered by bugs elsewhere. It is harmless, and potentially beneficial, to limit the damage by masking any such unexpected interrupts. This patch adds disabling of interrupts from any pins that should not have been allowed to interrupt, in addition to emitting a message. Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Maintain active time on all chipsMichael Albaugh
There is a count of "active hours" maintained in EEPROM, to aid troubleshooting. The definition of "active" is based on traffic exceeding a threshold in any given 5-second polling interval. As originally written, the check was inadvertently bypassed for chips whose counters were 64-bits wide, and only applied to chips with 32-bit wide counters. This patch moves the test for amount of traffic "out" to a more common location, rather than depending on a side-effect of the software emulation of 64-bit counts on chips whose hardware is only 32-bits wide. Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Fix QHT7040 serial number checkDave Olson
Remove all the OEM and bringup boards, and complain and fail initialization if one is found. QHT7040 with GPIO rework (128ywwuuuu) is OK, older 112ywwuuuu is no longer supported). The check that had been added was failing both the 112 and 128 series. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Indicate a couple of chip bugs to userspaceArthur Jones
A couple of chip bugs in the iba6110 and in the iba6120 are not in more recent chips. This first bug swaps two of the pioavail register locations. In the second bug, the chip can sometimes forget to dma the pio avail register to memory. We indicate the presence of these bugs with runtime flags and we indicate the presence of the flags by bumping the SWMINOR. Signed-off-by: Arthur Jones <arthur.jones@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: iba6110 rev4 no longer needs recv header overrun workaroundArthur Jones
iba6110 rev3 and earlier had a chip bug where the chip could overrun the recv header queue. rev4 fixed this chip bug so userspace no longer needs to workaround it. Now we only set the workaround flag for older chip versions. Signed-off-by: Arthur Jones <arthur.jones@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_closeArthur Jones
ipath_poll() suffered from a couple subtle bugs. Under the right conditions we could leave recv interrupts enabled on an ipath user context on close, thereby taking potentially unwanted interrupts on the next open -- this is fixed by unconditionally turning off recv interrupts on close. Also, we now use counters rather than set/clear bits which allows us to make sure we catch all interrupts at the cost of changing the semantics slightly (it's now give me all events since the last time I called poll() rather than give me all events since I called _this_ poll routine). We also added some memory barriers which may help ensure we get all notifications in a timely manner. Signed-off-by: Arthur Jones <arthur.jones@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Remove duplicate copy of LMCRalph Campbell
The LMC value was being saved by the SMA in two places. This patch cleans it up so only one copy is kept. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Add ability to set the LMC via the sysfs debugging interfaceRalph Campbell
This patch adds the ability to set the LMC via a sysfs file as if the SM sent a SubnSet(PortInfo) MAD. It is useful for debugging when no SM is running. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Optimize completion queue entry insertion and pollingRalph Campbell
The code to add an entry to the completion queue stored the QPN which is needed for the user level verbs view of the completion queue entry but the kernel struct ib_wc contains a pointer to the QP instead of a QPN. When the kernel polled for a completion queue entry, the QPN was lookup up and the QP pointer recovered. This patch stores the CQE differently based on whether the CQ is a kernel CQ or a user CQ thus avoiding the QPN to QP lookup overhead. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHEDRalph Campbell
This patch implements the IB_EVENT_QP_LAST_WQE_REACHED event which is needed by ib_ipoib to destroy the QP when used in connected mode. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Generate flush CQE when QP is in error stateRalph Campbell
Follow the IB spec. (C10-96) for post send which states that a flushed completion event should be generated for work requests posted when a QP is in the error state. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Remove redundant codeRalph Campbell
This patch removes some redundant initialization code. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Future proof eeprom checksum code (contents reading)Dave Olson
In an earlier change, the amount of data read from the flash was mistakenly limited to the size known to the current driver. This causes problems when the length is increased, and written with the new longer version; the checksum would fail because not enough data was read. Always read the full 128 byte length to prevent this. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediateRalph Campbell
This patch fixes a bug in the receive processing for UC RDMA WRITE with immediate which caused the last packet to be dropped. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Correctly describe workaround for TID write chip bugDave Olson
This is a comment change, only, correcting the comment to match the implemented workaround, rather than the original workaround, and clarifying why it's needed. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Remove unneeded code for ipathfsRalph Campbell
The ipathfs file system is used to export binary data verses ASCII data such as through /sys. This patch removes some unneeded files since the data is available through other /sys files. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Verify host bus bandwidth to chip will not limit performanceDave Olson
There have been a number of issues where host bandwidth via HT or PCIe to the InfiniPath chip has been limited in some fashion (BIOS, configuration, etc.), resulting in user confusion. This check gives a clear warning that something is wrong and needs to be resolved. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Change UD to queue work requests like RC & UCRalph Campbell
The code to post UD sends tried to process work requests at the time ib_post_send() is called without using a WQE queue. This was fine as long as HW resources were available for sending a packet. This patch changes UD to be handled more like RC and UC and shares more code. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Performance optimization for CPU differencesRalph Campbell
Different processors have different ordering restrictions for write combining. By taking advantage of this, we can eliminate some write barriers when writing to the send buffers. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: iba6110 rev4 GPIO counters supportArthur Jones
On iba6110 rev4, support for three more IB counters were added. The LocalLinkIntegrityError counter, the ExcessiveBufferOverrunErrors counter and support for error counting of flow control packets on an invalid VL. These counters trigger GPIO interrupts and the sw keeps track of the counts. Since we also use GPIO interrupts to signal packet reception, we need to turn off the fast interrupts, or we risk losing a GPIO interrupt. Signed-off-by: Arthur Jones <arthur.jones@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Fix clipping of device limits to INT_MAXRoland Dreier
Doing min_t(int, foo, INT_MAX) doesn't work correctly, because if foo is bigger than INT_MAX, then when treated as a signed integer, it will become negative and hence such an expression is just an elaborate NOP. Fix such cases in ehca to do min_t(unsigned, foo, INT_MAX) instead. This fixes negative reported values for max_cqe, max_pd and max_ah: Before: max_cqe: -64 max_pd: -1 max_ah: -1 After: max_cqe: 2147483647 max_pd: 2147483647 max_ah: 2147483647 Based on a bug report and fix from Anton Blanchard <anton@samba.org>. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IPoIB/cm: Clean up initialization of QP attr in ipoib_cm_create_tx_qp()Dotan Barak
Make the way QP is being created in ipoib_cm_create_tx_qp() consistent with ipoib_cm_create_rx_qp(). Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mthca: Use mmiowb() to avoid firmware commands getting jumbled upRoland Dreier
Firmware commands are sent to the HCA by writing multiple words to a command register block. Access to this block of registers is serialized with a mutex. However, on large SGI systems, problems were seen with multiple CPUs issuing FW commands at the same time, because the writes to the register block may be reordered within the system interconnect and reach the HCA in a different order than they were issued (even with the mutex). Fix this by adding an mmiowb() before dropping the mutex. Tested-by: Arthur Kepner <akepner@sgi.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09RDMA/cma: Queue IB CM MRAs to avoid unnecessary remote retriesSean Hefty
Automatically queue MRA message to decrease the number of retries sent by the remote side during connection establishment. This also has the effect of increasing the overall connection timeout without using a longer retry time in the case of dropped packets. Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/cm: Modify interface to send MRAs in response to duplicate messagesSean Hefty
The IB CM provides a message received acknowledged (MRA) message that can be sent to indicate that a REQ or REP message has been received, but will require more time to process than the timeout specified by those messages. In many cases, the application may not know how long it will take to respond to a CM message, but the majority of the time, it will usually respond before a retry has been sent. Rather than sending an MRA in response to all messages just to handle the case where a longer timeout is needed, it is more efficient to queue the MRA for sending in case a duplicate message is received. This avoids sending an MRA when it is not needed, but limits the number of times that a REQ or REP will be resent. It also provides for a simpler implementation than generating the MRA based on a timer event. (That is, trying to send the MRA after receiving the first REQ or REP if a response has not been generated, so that it is received at the remote side before a duplicate REQ or REP has been received) Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mthca: Increase max number of QPs per multicast group to 56Roland Dreier
Increase the number of QPs allowed per multicast group from 8 to 56. This allows for one QP per core on 16-core systems, which are now quite common, and allows some space for future growth. This is basically the same patch that Jack Morgenstein <jackm@dev.mellanox.co.il> just supplied for mlx4. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mlx4: Implement FMRsJack Morgenstein
Implement FMRs for mlx4. This is an adaptation of code from mthca. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09mlx4_core: Write MTTs from CPU instead with of WRITE_MTT FW commandJack Morgenstein
Write MTT entries directly to ICM from the driver (eliminating use of WRITE_MTT command). This reduces the number of FW commands needed to register an MR by at least a factor of 2 and speeds up memory registration significantly. This code will also be used to implement FMRs. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/uverbs: Make ib_uverbs_release_event_file() staticRoland Dreier
ib_uverbs_release_event_file() is only used in uverbs_main.c, so make it static to that file. Also move the definition before the first use, so a forward declaration is not needed. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/umad: Fix bit ordering and 32-on-64 problems on big endian systemsRoland Dreier
The declaration of struct ib_user_mad_reg_req.method_mask[] exported to userspace was an array of __u32, but the kernel internally treated it as a bitmap made up of longs. This makes a difference for 64-bit big-endian kernels, where numbering the bits in an array of__u32 gives: |31.....0|63....31|95....64|127...96| while numbering the bits in an array of longs gives: |63..............0|127............64| 64-bit userspace can handle this by just treating method_mask[] as an array of longs, but 32-bit userspace is really stuck: the meaning of the bits in method_mask[] depends on whether the kernel is 32-bit or 64-bit, and there's no sane way for userspace to know that. Fix this by updating <rdma/ib_user_mad.h> to make it clear that method_mask[] is an array of longs, and using a compat_ioctl method to convert to an array of 64-bit longs to handle the 32-on-64 problem. This fixes the interface description to match existing behavior (so working binaries continue to work) in almost all situations, and gives consistent semantics in the case of 32-bit userspace that can run on either a 32-bit or 64-bit kernel, so that the same binary can work for both 32-on-32 and 32-on-64 systems. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/umad: Add P_Key index supportRoland Dreier
Add support for setting the P_Key index of sent MADs and getting the P_Key index of received MADs. This requires a change to the layout of the ABI structure struct ib_user_mad_hdr, so to avoid breaking compatibility, we default to the old (unchanged) ABI and add a new ioctl IB_USER_MAD_ENABLE_PKEY that allows applications that are aware of the new ABI to opt into using it. We plan on switching to the new ABI by default in a year or so, and this patch adds a warning that is printed when an application uses the old ABI, to push people towards converting to the new ABI. Signed-off-by: Roland Dreier <rolandd@cisco.com> Reviewed-by: Sean Hefty <sean.hefty@intel.com> Reviewed-by: Hal Rosenstock <hal@xsigo.com>