aboutsummaryrefslogtreecommitdiff
path: root/drivers/md/raid1.c
AgeCommit message (Collapse)Author
2008-05-24md: restart recovery cleanly after device failure.NeilBrown
When we get any IO error during a recovery (rebuilding a spare), we abort the recovery and restart it. For RAID6 (and multi-drive RAID1) it may not be best to restart at the beginning: when multiple failures can be tolerated, the recovery may be able to continue and re-doing all that has already been done doesn't make sense. We already have the infrastructure to record where a recovery is up to and restart from there, but it is not being used properly. This is because: - We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR, which causes the recovery not be be checkpointed. - We remove spares and then re-added them which loses important state information. The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't needed. If there is an error, the relevant drive will be marked as Faulty, and that is enough to ensure correct handling of the error. So we first remove MD_RECOVERY_ERR, changing some of the uses of it to MD_RECOVERY_INTR. Then we cause the attempt to remove a non-faulty device from an array to fail (unless recovery is impossible as the array is too degraded). Then when remove_and_add_spares attempts to remove the devices on which recovery can continue, it will fail, they will remain in place, and recovery will continue on them as desired. Issue: If we are halfway through rebuilding a spare and another drive fails, and a new spare is immediately available, do we want to: 1/ complete the current rebuild, then go back and rebuild the new spare or 2/ restart the rebuild from the start and rebuild both devices in parallel. Both options can be argued for. The code currently takes option 2 as a/ this requires least code change b/ this results in a minimally-degraded array in minimal time. Cc: "Eivind Sarto" <ivan@kasenna.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24md: raid1: Fix restoration of bio between failed read and write.NeilBrown
When performing a "recovery" or "check" pass on a RAID1 array, we read from each device and possible, if there is a difference or a read error, write back to some devices. We use the same 'bio' for both read and write, resetting various fields between the two operations. We forgot to reset bv_offset and bv_len however. These are often left unchanged, but in the case where there is an IO error one or two sectors into a page, they are changed. This results in correctable errors not being corrected properly. It does not result in any data corruption. Cc: "Fairbanks, David" <David.Fairbanks@stratus.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24md: fix possible oops when removing a bitmap from an active arrayNeilBrown
It is possible to add a write-intent bitmap to an active array, or remove the bitmap that is there. When we do with the 'quiesce' the array, which causes make_request to block in "wait_barrier()". However we are sampling the value of "mddev->bitmap" before the wait_barrier call, and using it afterwards. This can result in using a bitmap structure that has been freed. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-14Remove blkdev warning triggered by using mdNeil Brown
As setting and clearing queue flags now requires that we hold a spinlock on the queue, and as blk_queue_stack_limits is called without that lock, get the lock inside blk_queue_stack_limits. For blk_queue_stack_limits to be able to find the right lock, each md personality needs to set q->queue_lock to point to the appropriate lock. Those personalities which didn't previously use a spin_lock, us q->__queue_lock. So always initialise that lock when allocated. With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no longer cause warnings as it will be clear that the proper lock is held. Thanks to Dan Williams for review and fixing the silly bugs. Signed-off-by: NeilBrown <neilb@suse.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Alistair John Strachan <alistair@devzero.co.uk> Cc: Nick Piggin <npiggin@suse.de> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Jacek Luczak <difrost.kernel@gmail.com> Cc: Prakash Punnoor <prakash@punnoor.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30md: support blocking writes to an array on device failureDan Williams
Allows a userspace metadata handler to take action upon detecting a device failure. Based on an original patch by Neil Brown. Changes: -added blocked_wait waitqueue to rdev -don't qualify Blocked with Faulty always let userspace block writes -added md_wait_for_blocked_rdev to wait for the block device to be clear, if userspace misses the notification another one is sent every 5 seconds -set MD_RECOVERY_NEEDED after clearing "blocked" -kill DoBlock flag, just test mddev->external Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28raid: remove leading TAB on printk messagesNick Andrew
MD drivers use one printk() call to print 2 log messages and the second line may be prefixed by a TAB character. It may also output a trailing space before newline. klogd (I think) turns the TAB character into the 2 characters '^I' when logging to a file. This looks ugly. Instead of a leading TAB to indicate continuation, prefix both output lines with 'raid:' or similar. Also remove any trailing space in the vicinity of the affected code and consistently end the sentences with a period. Signed-off-by: Nick Andrew <nick@nick-andrew.net> Cc: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04md: fix possible raid1/raid10 deadlock on read error during resyncNeilBrown
Thanks to K.Tanaka and the scsi fault injection framework, here is a fix for another possible deadlock in raid1/raid10 error handing. If a read request returns an error while a resync is happening and a resync request is pending, the attempt to fix the error will block until the resync progresses, and the resync will block until the read request completes. Thus a deadlock. This patch fixes the problem. Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04md: fix deadlock in md/raid1 and md/raid10 when handling a read errorNeilBrown
When handling a read error, we freeze the array to stop any other IO while attempting to over-write with correct data. This is done in the raid1d(raid10d) thread and must wait for all submitted IO to complete (except for requests that failed and are sitting in the retry queue - these are counted in ->nr_queue and will stay there during a freeze). However write requests need attention from raid1d as bitmap updates might be required. This can cause a deadlock as raid1 is waiting for requests to finish that themselves need attention from raid1d. So we create a new function 'flush_pending_writes' to give that attention, and call it in freeze_array to be sure that we aren't waiting on raid1d. Thanks to "K.Tanaka" <k-tanaka@ce.jp.nec.com> for finding and reporting this problem. Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06md: change ITERATE_RDEV to rdev_for_eachNeilBrown
As this is more in line with common practice in the kernel. Also swap the args around to be more like list_for_each. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06md: allow a maximum extent to be set for resyncingNeilBrown
This allows userspace to control resync/reshape progress and synchronise it with other activities, such as shared access in a SAN, or backing up critical sections during a tricky reshape. Writing a number of sectors (which must be a multiple of the chunk size if such is meaningful) causes a resync to pause when it gets to that point. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06md: Update md bitmap during resync.NeilBrown
Currently an md array with a write-intent bitmap does not updated that bitmap to reflect successful partial resync. Rather the entire bitmap is updated when the resync completes. This is because there is no guarentee that resync requests will complete in order, and tracking each request individually is unnecessarily burdensome. However there is value in regularly updating the bitmap, so add code to periodically pause while all pending sync requests complete, then update the bitmap. Doing this only every few seconds (the same as the bitmap update time) does not notciably affect resync performance. [snitzer@gmail.com: export bitmap_cond_end_sync] Signed-off-by: Neil Brown <neilb@suse.de> Cc: "Mike Snitzer" <snitzer@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-09Add UNPLUG traces to all appropriate placesAlan D. Brunelle
Added blk_unplug interface, allowing all invocations of unplugs to result in a generated blktrace UNPLUG. Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-19Convert files to UTF-8 and some cleanupsJan Engelhardt
* Convert files to UTF-8. * Also correct some people's names (one example is Eißfeldt, which was found in a source file. Given that the author used an ß at all in a source file indicates that the real name has in fact a 'ß' and not an 'ss', which is commonly used as a substitute for 'ß' when limited to 7bit.) * Correct town names (Goettingen -> Göttingen) * Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313) Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-17md: make sure read errors are auto-corrected during a 'check' resync in raid1NeilBrown
Whenever a read error is found, we should attempt to overwrite with correct data to 'fix' it. However when do a 'check' pass (which compares data blocks that are successfully read, but doesn't normally overwrite) we don't do that. We should. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16block: convert blkdev_issue_flush() to use empty barriersJens Axboe
Then we can get rid of ->issue_flush_fn() and all the driver private implementations of that. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Drop 'size' argument from bio_endio and bi_end_ioNeilBrown
As bi_end_io is only called once when the reqeust is complete, the 'size' argument is now redundant. Remove it. Now there is no need for bio_endio to subtract the size completed from bi_size. So don't do that either. While we are at it, change bi_end_io to return void. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-08-22md: correctly update sysfs when a raid1 is reshapedNeilBrown
When a raid1 array is reshaped (number of drives changed), the list of devices is compacted, so that slots for missing devices are filled with working devices from later slots. This requires the "rd%d" symlinks in sysfs to be updated. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-22md: make sure a re-add after a restart honours bitmap when resyncingNeilBrown
Commit 1757128438d41670ded8bc3bc735325cc07dc8f9 was slightly bad. If an array has a write-intent bitmap, and you remove a drive, then readd it, only the changed parts should be resynced. However after the above commit, this only works if the array has not been shut down and restarted. This is because it sets 'fullsync' at little more often than it should. This patch is more careful. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-24[BLOCK] Get rid of request_queue_t typedefJens Axboe
Some of the code has been gradually transitioned to using the proper struct request_queue, but there's lots left. So do a full sweet of the kernel and get rid of this typedef and replace its uses with the proper type. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-07-17md: change bitmap_unplug and others to void functionsNeilBrown
bitmap_unplug only ever returns 0, so it may as well be void. Two callers try to print a message if it returns non-zero, but that message is already printed by bitmap_file_kick. write_page returns an error which is not consistently checked. It always causes BITMAP_WRITE_ERROR to be set on an error, and that can more conveniently be checked. When the return of write_page is checked, an error causes bitmap_file_kick to be called - so move that call into write_page - and protect against recursive calls into bitmap_file_kick. bitmap_update_sb returns an error that is never checked. So make these 'void' and be consistent about checking the bit. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-06-16md: fix bug in error handling during raid1 repairMike Accetta
If raid1/repair (which reads all block and fixes any differences it finds) hits a read error, it doesn't reset the bio for writing before writing correct data back, so the read error isn't fixed, and the device probably gets a zero-length write which it might complain about. Signed-off-by: Neil Brown <neilb@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-10md: avoid a possibility that a read error can wrongly propagate through ↵NeilBrown
md/raid1 to a filesystem. When a raid1 has only one working drive, we want read error to propagate up to the filesystem as there is no point failing the last drive in an array. Currently the code perform this check is racy. If a write and a read a both submitted to a device on a 2-drive raid1, and the write fails followed by the read failing, the read will see that there is only one working drive and will pass the failure up, even though the one working drive is actually the *other* one. So, tighten up the locking. Signed-off-by: Neil Brown <neilb@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09Revert "md: improve partition detection in md array"Linus Torvalds
This reverts commit 5b479c91da90eef605f851508744bfe8269591a0. Quoth Neil Brown: "It causes an oops when auto-detecting raid arrays, and it doesn't seem easy to fix. The array may not be 'open' when do_md_run is called, so bdev->bd_disk might be NULL, so bd_set_size can oops. This whole approach of opening an md device before it has been assembled just seems to get more and more painful. I think I'm going to have to come up with something clever to provide both backward comparability with usage expectation, and sane integration into the rest of the kernel." Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09md: improve partition detection in md arrayNeilBrown
md currently uses ->media_changed to make sure rescan_partitions is call on md array after they are assembled. However that doesn't happen until the array is opened, which is later than some people would like. So use blkdev_ioctl to do the rescan immediately that the array has been assembled. This means we can remove all the ->change infrastructure as it was only used to trigger a partition rescan. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-01-26[PATCH] md: fix potential memalloc deadlock in mdNeilBrown
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held, it is possible for a deadlock to eventuate. This happens if the array was marked 'clean', and the memalloc triggers a write-out to the md device. For the writeout to succeed, the array must be marked 'dirty', and that requires getting the mddev_lock. So, before attempting a GFP_KERNEL allocation while holding the lock, make sure the array is marked 'dirty' (unless it is currently read-only). Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-01-26[PATCH] md: make 'repair' actually work for raid1NeilBrown
When 'repair' finds a block that is different one the various parts of the mirror. it is meant to write a chosen good version to the others. However it currently writes out the original data to each. The memcpy to make all the data the same is missing. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-01-11[PATCH] md: pass down BIO_RW_SYNC in raid{1,10}Lars Ellenberg
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus introducing additional latency. Fixing this in raid1 and raid10 seems to be straightforward enough. For our particular usage case in DRBD, passing this flag improved some initialization time from ~5 minutes to ~5 seconds. Acked-by: NeilBrown <neilb@suse.de> Signed-off-by: Lars Ellenberg <lars@linbit.com> Acked-by: Jens Axboe <jens.axboe@oracle.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13[PATCH] md: Don't assume that READ==0 and WRITE==1 - use the names explicitlyNeilBrown
Thanks Jens for alerting me to this. Cc: Jens Axboe <jens.axboe@oracle.com> Cc: <raziebe@gmail.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10[PATCH] md: assorted md and raid1 one-linersNeilBrown
Fix few bugs that meant that: - superblocks weren't alway written at exactly the right time (this could show up if the array was not written to - writting to the array causes lots of superblock updates and so hides these errors). - restarting device recovery after a clean shutdown (version-1 metadata only) didn't work as intended (or at all). 1/ Ensure superblock is updated when a new device is added. 2/ Remove an inappropriate test on MD_RECOVERY_SYNC in md_do_sync. The body of this if takes one of two branches depending on whether MD_RECOVERY_SYNC is set, so testing it in the clause of the if is wrong. 3/ Flag superblock for updating after a resync/recovery finishes. 4/ If we find the neeed to restart a recovery in the middle (version-1 metadata only) make sure a full recovery (not just as guided by bitmaps) does get done. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-28[PATCH] md: fix printk format warnings, seen on powerpc64:Randy Dunlap
drivers/md/raid1.c:1479: warning: long long unsigned int format, long unsigned int arg (arg 4) drivers/md/raid10.c:1475: warning: long long unsigned int format, long unsigned int arg (arg 4) Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03[PATCH] md: define ->congested_fn for raid1, raid10, and multipathNeilBrown
raid1, raid10 and multipath don't report their 'congested' status through bdi_*_congested, but should. This patch adds the appropriate functions which just check the 'congested' status of all active members (with appropriate locking). raid1 read_balance should be modified to prefer devices where bdi_read_congested returns false. Then we could use the '&' branch rather than the '|' branch. However that should would need some benchmarking first to make sure it is actually a good idea. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03[PATCH] md: Improve locking around error handlingNeilBrown
The error handling routines don't use proper locking, and so two concurrent errors could trigger a problem. So: - use test-and-set and test-and-clear to synchonise the In_sync bits with the ->degraded count - use the spinlock to protect updates to the degraded count (could use an atomic_t but that would be a bigger change in code, and isn't really justified) - remove un-necessary locking in raid5 Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03[PATCH] md: Remove working_disks from raid1 state dataNeilBrown
It is equivalent to conf->raid_disks - conf->mddev->degraded. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03[PATCH] md: Factor out part of raid1d into a separate functionNeilBrown
raid1d has toooo many nested block, so take the fix_read_error functionality out into a separate function. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03[PATCH] md: replace magic numbers in sb_dirty with well defined bit flagsNeilBrown
Instead of magic numbers (0,1,2,3) in sb_dirty, we have some flags instead: MD_CHANGE_DEVS Some device state has changed requiring superblock update on all devices. MD_CHANGE_CLEAN The array has transitions from 'clean' to 'dirty' or back, requiring a superblock update on active devices, but possibly not on spares MD_CHANGE_PENDING A superblock update is underway. We wait for an update to complete by waiting for all flags to be clear. A flag can be set at any time, even during an update, without risk that the change will be lost. Stop exporting md_update_sb - isn't needed. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-01[PATCH] md: Fix issues with referencing rdev in md/raid1NeilBrown
We need to be careful when referencing mirrors[i].rdev. It can disappear under us at various times. So: fix a couple of problem places. comment a couple of non-problem places move an 'atomic_add' which deferences rdev down a little way to some where where it is sure to not be NULL. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-08-27[PATCH] md: fix recent breakage of md/raid1 array checkingNeilBrown
A recent patch broke the ability to do a user-request check of a raid1. This patch fixes the breakage and also moves a comment that was dislocated by the same patch. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10[PATCH] md: include sector number in messages about corrected read errorsNeilBrown
This is generally useful, but particularly helps see if it is the same sector that always needs correcting, or different ones. [akpm@osdl.org: fix printk warnings] Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10[PATCH] md: fix usage of wrong variable in raid1NeilBrown
Though it rarely matters, we should be using 's' rather than r1_bio->sector here. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26[PATCH] md: Allow re-add to work on array without bitmapsNeilBrown
When an array has a bitmap, a device can be removed and re-added and only blocks changes since the removal (as recorded in the bitmap) will be resynced. It should be possible to do a similar thing to arrays without bitmaps. i.e. if a device is removed and re-added and *no* changes have been made in the interim, then the add should not require a resync. This patch allows that option. This means that when assembling an array one device at a time (e.g. during device discovery) the array can be enabled read-only as soon as enough devices are available, but extra devices can still be added without causing a resync. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26[PATCH] md: allow checkpoint of recovery with version-1 superblockNeilBrown
For a while we have had checkpointing of resync. The version-1 superblock allows recovery to be checkpointed as well, and this patch implements that. Due to early carelessness we need to add a feature flag to signal that the recovery_offset field is in use, otherwise older kernels would assume that a partially recovered array is in fact fully recovered. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26[PATCH] md: reformat code in raid1_end_write_request to avoid gotoNeilBrown
A recent change made this goto unnecessary, so reformat the code to make it clearer what is happening. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01[PATCH] md: Fix 'rdev->nr_pending' count when retrying barrier requestsNeilBrown
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference in ->nr_pending over the whole retry. Currently, we only hold the reference if the failed request is the *last* one to finish - which is silly, because it would normally be the first to finish. So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01[PATCH] md: Improve detection of lack of barrier support in raid1NeilBrown
Move the test for 'do barrier work' down a bit so that if the first write to a raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will cause the right thing to happen. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01[PATCH] md: Change ENOTSUPP to EOPNOTSUPPNeilBrown
Because that is what you get if a BIO_RW_BARRIER isn't supported! Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-01BUG_ON() Conversion in md/raid1.cEric Sesterhenn
this changes if() BUG(); constructs to BUG_ON() which is cleaner and can better optimized away Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-03-31[PATCH] md: Don't clear bits in bitmap when writing to one device fails ↵NeilBrown
during recovery Currently a device failure during recovery leaves bits set in the bitmap. This normally isn't a problem as the offending device will be rejected because of errors. However if device re-adding is being used with non-persistent bitmaps, this can be a problem. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27[PATCH] md: Restore 'remaining' count when retrying an write operationNeilBrown
When retrying a write due to barrier failure, we don't reset 'remaining', so it goes negative and never hits 0 again. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27[PATCH] md: Split reshape handler in check_reshape and start_reshapeNeilBrown
check_reshape checks validity and does things that can be done instantly - like adding devices to raid1. start_reshape initiates a restriping process to convert the whole array. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27[PATCH] md: Checkpoint and allow restart of raid5 reshapeNeilBrown
We allow the superblock to record an 'old' and a 'new' geometry, and a position where any conversion is up to. The geometry allows for changing chunksize, layout and level as well as number of devices. When using verion-0.90 superblock, we convert the version to 0.91 while the conversion is happening so that an old kernel will refuse the assemble the array. For version-1, we use a feature bit for the same effect. When starting an array we check for an incomplete reshape and restart the reshape process if needed. If the reshape stopped at an awkward time (like when updating the first stripe) we refuse to assemble the array, and let user-space worry about it. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>