| Age | Commit message (Collapse) | Author |
|---|
|
A user noticed that there would continue to be 4-6 keypresses even after the
user stopped holding down the button. This was because we were not reading
the bulk pipe faster than the firmware was injecting information, which would
result in a backlog.
Make the query interval faster, and increase the number of cycles before we
start repeating to compensate.
Thanks to Knud Poulsen <knud.poulsen@nokia.com> for pointing this out.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
New firmware image brings enhanced tuning performance.
Firmware is available for download at the following location:
http://www.steventoth.net/linux/sms1xxx
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Don't reconnect device in the USB-bus. Reconnect command was not
executed every time by device firmware and that causes harm.
Reconnection is not needed so remove it.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The format for reading the IR controller changed in firmware 1.20. It now
provides the events on bulk endpoint 1 instead of using a control request.
Support the new format, providing backward compatibility for users who might
be using older firmware.
Thanks to Patrick Boettcher <patrick.boettcher@desy.de> for providing the
required information on how the version 1.20 firmware works.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It is not safe to assume that the i2c gate will be open before issuing the
command to power down the tuner. In fact, many demods only open the gate
long enough to issue the tuning command.
This fix allows power management to work properly for those tuners behind an
i2c gate (in my case the problem was with the HVR-950Q)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
ATSC should be considered a legacy delivery system, or else fields such as
p->u.vsb.modulation do not get populated (resulting in set_frontend failures)
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
--
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Free allocated memory
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Free allocated memory
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Added validation for ttusb_alloc_iso_urbs
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Added validation for NULL pointer
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Added validation for NULL pointer
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- use static to avoid compile warnings
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- ! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
anysee_usb_mutex is initialized at every time the anysee device is probed.
If the second anysee device is probed while anysee_usb_mutex is locked by
the first anysee device, the mutex is broken.
This patch fixes by initialize anysee_usb_mutex statically rather
than initialize at probe time.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When inadvertently hot-unplugging a WT-220U USB DVB-T receiver with
2.6.24, I was met with an oops [1]. The problem is relevant to
2.6.25/26-rc also.
dvb_frontend_init() was called either from re-creation of the kdvb-fe0
thread - seems unlikely, or someone called
dvb_frontend_reinitialise(), causing this path in the thread - really
unlikely, as I can't find any call-site for it.
Either way, quite a number of drivers call dvb_usb_generic_rw() [2]
without checking the validity of the relevant member in the
dvb_usb_device struct - which had changed. Having dvb_usb_generic_rw()
sanity-check and fail (rather than loading from 0x120) seems
reasonable defensive programming [3], in light of it being called in
this way.
The problem with this, is that drivers don't check the return code of
the init call [4]. Does it make sense to cook a patch which allows the
failure to be propagated back up, or am I missing something else?
Thanks,
Daniel
<whoops, hot unplug>
[83711.538485] dvb-usb: bulk message failed: -71 (1/0)
[83711.538875] dvb-usb: bulk message failed: -71 (1/0)
[83711.538899] usb 7-5: USB disconnect, address 3
[83711.538905] dvb-usb: bulk message failed: -22 (1/0)
[83711.538924] dvb-usb: bulk message failed: -22 (1/0)
[83711.538943] dvb-usb: bulk message failed: -22 (1/0)
[83711.588979] dvb-usb: bulk message failed: -22 (1/0)
[83711.589031] dvb-usb: bulk message failed: -22 (1/0)
[83711.589078] dvb-usb: bulk message failed: -22 (1/0)
[83711.589122] dvb-usb: bulk message failed: -22 (1/0)
[83711.589167] dvb-usb: bulk message failed: -22 (1/0)
[83711.639233] dvb-usb: bulk message failed: -22 (1/0)
[83711.639282] dvb-usb: bulk message failed: -22 (1/0)
[83711.639330] dvb-usb: bulk message failed: -22 (1/0)
[83711.639374] dvb-usb: bulk message failed: -22 (1/0)
[83711.639421] dvb-usb: bulk message failed: -22 (1/0)
[83711.658391] dvb-usb: bulk message failed: -22 (1/0)
[83768.174281] dvb-usb: bulk message failed: -22 (2/-32512)
[83768.174350] Unable to handle kernel NULL pointer
dereference<6>dvb-usb: WideView WT-220U PenType Receiver
(Typhoon/Freecom) successfully deinitialized and disconnected.
[83768.174459] at 0000000000000120 RIP:
[83768.174459] [<ffffffff88339b4f>] :dvb_usb:dvb_usb_generic_rw+0x2f/0x1a0
[83768.174580] PGD 0
[83768.174643] Oops: 0000 [1] SMP
[83768.174723] CPU 0
[83768.174782] Modules linked in: nfsd auth_rpcgss exportfs nfs lockd
nfs_acl sunrpc af_packet xt_length ipt_tos ipt_TOS xt_CLASSIFY sch_sfq
sch_htb ipt_MASQUERADE ipt_REDIRECT xt_limit xt_state xt_tcpudp
iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack iptable_mangle
iptable_filter ip_tables x_tables xfs sbp2 parport_pc lp parport loop
ftdi_sio usbserial evdev dvb_usb_dtt200u dvb_usb dvb_core i2c_core
sky2 iTCO_wdt iTCO_vendor_support snd_hda_intel shpchp snd_pcm
snd_timer snd_page_alloc snd_hwdep snd pci_hotplug soundcore ipv6
button intel_agp ext3 jbd mbcache sg sd_mod ata_generic pata_acpi ahci
ata_piix libata scsi_mod ohci1394 ieee1394 ehci_hcd uhci_hcd usbcore
e1000 thermal processor fan fbcon tileblit font bitblit softcursor
fuse
[83768.176968] Pid: 5732, comm: kdvb-fe-0 Not tainted 2.6.24-16-server #1
[83768.177009] RIP: 0010:[<ffffffff88339b4f>] [<ffffffff88339b4f>]
:dvb_usb:dvb_usb_generic_rw+0x2f/0x1a0
[83768.177096] RSP: 0018:ffff810021939df0 EFLAGS: 00010286
[83768.177138] RAX: ffff81003bc7cc00 RBX: 0000000000000001 RCX: 0000000000000000
[83768.177181] RDX: 0000000000000001 RSI: ffff810021939e67 RDI: 0000000000000000
[83768.177223] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[83768.177267] R10: ffff810001009880 R11: 0000000000000001 R12: ffff81003c10b400
[83768.177311] R13: ffff81003c10b5b0 R14: ffff810021939ec0 R15: 0000000000000000
[83768.177354] FS: 0000000000000000(0000) GS:ffffffff805c3000(0000)
knlGS:0000000000000000
[83768.177409] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
[83768.177449] CR2: 0000000000000120 CR3: 0000000000201000 CR4: 00000000000006e0
[83768.177491] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[83768.177534] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[83768.177576] Process kdvb-fe-0 (pid: 5732, threadinfo
ffff810021938000, task ffff81003bd1b7a0)
[83768.177629] Stack: ffff81003e9b6828 0000000000000000
ffff8100378369f8 0000000000000000
[83768.177800] ffff81003bd1b7a0 ffff810037836d48 ffff81003bc7cc30
ffff81003c10b400
[83768.177943] ffff81003c10b5b0 ffff810021939ec0 ffff81003c10b5e0
ffffffff88342452
[83768.178054] Call Trace:
[83768.178130] [<ffffffff88342452>] :dvb_usb_dtt200u:dtt200u_fe_init+0x22/0x30
[83768.178178] [<ffffffff88339f6a>] :dvb_usb:dvb_usb_fe_wakeup+0x3a/0x50
[83768.178229] [<ffffffff88325c41>] :dvb_core:dvb_frontend_init+0x21/0x70
[83768.178278] [<ffffffff8832746b>] :dvb_core:dvb_frontend_thread+0x8b/0x370
[83768.178329] [<ffffffff883273e0>] :dvb_core:dvb_frontend_thread+0x0/0x370
[83768.178382] [<ffffffff80253e3b>] kthread+0x4b/0x80
[83768.178427] [<ffffffff8020d198>] child_rip+0xa/0x12
[83768.178473] [<ffffffff80253df0>] kthread+0x0/0x80
[83768.178514] [<ffffffff8020d18e>] child_rip+0x0/0x12
[83768.178557]
[83768.178594]
[83768.178594] Code: 44 8b 87 20 01 00 00 49 89 f4 45 89 ce 45 85 c0
0f 84 ad 00
[83768.179167] RIP [<ffffffff88339b4f>] :dvb_usb:dvb_usb_generic_rw+0x2f/0x1a0
[83768.179234] RSP <ffff810021939df0>
[83768.179271] CR2: 0000000000000120
[83768.179419] ---[ end trace dba8483163cb1700 ]---
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
config\tDVB_USB_CINERGY_T2 causes the make_kconfig.pl to forget to enable by default the compilation of cinergyT2 module.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Update Kconfig to add missing dependency on zl10353 for dtv5100 driver.
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
rather than implementing different ways leading to confusion.
This allows multiple gate_enable/disable's in the tuner_read/write
functions, thereby lesser number of I/O operations throughout,
eventually leading to better results. As a side effect demods that
detect the STOP bit for auto closing of the gate can be avoided, thereby
a very minimal gain in disabling the auto detect feature as well.
Improves readability on the device control.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Power down the s5h1411 demodulator when not in use (on the Pinnacle 801e, this
brings idle power from 123ma down to 84ma).
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
the desired modulation
If we are already at the desired modulation, there is no need to reconfigure
the demod (at a tuning time cost)
Note that this change revealed that although the datasheet says the demod
starts out in VSB-8 mode, the first tuning was failing consistently unless
we went through the work of setting the registers. So add a field to denote
this case so we always do the enable_frontend call, even if the first tuning
request is for VSB-8.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If you instruct the tuner to change frequencies, it can take up to 2500ms to
get a demod lock. By performing a soft reset after the tuning call (which
is consistent with how the Pinnacle 801e Windows driver behaves), you get
a demod lock inside of 300ms
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
s5h1411: Add the #define for an existing supporting I/F
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
s5h1411: Remove meaningless code
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
destroy bits
Adding a serialmode function to read/and/or/write the register for safety.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This includes new bit definitions for previously unknown bits.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This should improve performance.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
s5h1411: Improvements to the default registers
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A consolidated implementation will provide this generically through
asm/byteorder, remove direct includes to avoid breakage when the
changeover to the new implementation occurs.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove warning message during cx88-dvb compilation.
Also fixes double underline in function and struct names.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
| drivers/media/dvb/frontends/cx24116.c:573: warning: passing argument 3 of 'cx24116_writeregN' discards qualifiers from pointer target type
Make the `data' input pointer parameter of cx24116_writeregN() const to
kill the warning.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove spurious messages and turn into debug.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Christophe divulged the following:
"Since 8PSK (and higher mod) signals are very likely to have pilot symbols,
pilot_auto should start with pilot_on for 8PSK.
And since QPSK signals are unlikely to have pilot, pilot_auto should start
with pilot_off for QPSK.
Without the patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~900ms
with patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~100ms
"
This patch does as Cristophe asks. In emulated auto-pilot we
choose pilot-on for tuning PSK_8 and pilot-off for
tuning QPSK.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When moving from one frontend to another
an application could spawn multiple threads opening
the same new frontend and in some circumstances all of
these could become delayed waiting for the previous
frontend readers or previous frontend writer thread to
complete.
In this scenario the first thread will succeed on open
to bring the new frontend online but any others will return
EBUSY. This is a fault. If the first succeeds and all others
are on the same frontend then they should succeed also.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx24123: Checkpatch compliance
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
s5h1411: Checkpatch compliance
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
s5h1409: Checkpatch compliance
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx24116: Checkpatch compliance #3
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx22702: Checkpatch compliance
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
tda10048: Checkpatch compliance
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx24116: Checkpatch compliance #2
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx24116: Checkpatch compliance
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
MiniStick
Autodetect 2040:5520 and 2040:5530 as Hauppauge WinTV MiniStick
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This add frontend R/W mutual exclusion.
Prior to this point in time it was possible to open both
frontends simultaneously which an MFE card cannot support.
In order to stop this, a delayed open is performed which
has the following function:
- Return EBUSY after a configurable amount of time
if a frontend is unavailable due to the other being
in use.
- Only allow opening of a frontend if the kernel thread
of the other has stopped.
This solution was chosen to allow switching between
frontends to work as seamlessly as possible. When both
frontends are actually opened simultaneously then one
will only open, but if quick switching is performed
between one of many then the new open will succeed in
a clean fashion rather than interrupting a kernel
thread.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A detailed description from the original patches 2 years ago:
"The WinTV-HVR3000 has a single transport bus which is shared between
a DVB-T and DVB-S modulator. These patches build on the bus acquisition
cx88 work from a few weeks ago to add support for this.
So to applications the HVR3000 looks like this:
/dev/dvb/adapter0/fe0 (cx24123 DVB-S demod)
/dev/dvb/adapter0/fe1 (cx22702 DVB-T demod)
Additional boards continue as before, eg:
/dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod)
The basic change is removing the single instance of the videobuf_dvb in
cx8802_dev and saa7134_dev(?) and replacing it with a list and some
supporting functions.
*NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so
two or three current cx88 patches appear to be reversed by this tree,
this will be cleaned up in the near future. The patches missing change
the mutex handing to core->lock, fix an enumeration problem."
It should be recognised that a number of people have been maintaining
this patchset. Significant levels of Kudos to everyone one involved,
including but not limited to:
Darron Broad
Fabio M. Di Nitto
Carlo Scarfoglio
Hans Werner
Without the work of these people, and countless others, my two year old
patches would of died on the Mercurial linuxtv.org vine a long time
ago.
TODO: Revise these patches a little further so that the need for
demux1 and dvr0 is optional, not mandatory on the HVR3000.
HISTORY (darron):
This is the last update to MFE prepared by Hans which is based
upon the `scratchpad' diff created by Carlo.
All MFE work prior to that point must be attributed to Fabio
who ported and maintained Steve's original patch up to that
time.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
DVB-S2 delivery
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Now that device_create() has been audited, rename things back to the
original call to be sane.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
default.
cx24116: Change the default SNR units back to percentage by default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
S2API: Return error of the caller provides 0 commands.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A user tuning DVB-T via the S2API reports that this was not implemented,
and his tuning was failing.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
