Age | Commit message (Collapse) | Author |
|
Tuner setup were happening during i2c attach callback. This means that it would
happen on two conditions:
1) if tuner module weren't load, it will happen at request_module("tuner");
2) if tuner is not compiled as a module, or it is already loaded
(for example, on setups with more than one tuner), it will happen
when saa7134 registers I2C bus.
Due to that, if tuner were loaded, tuner setup will happen _before_ reading
the proper values at tuner eeprom. Since set_addr refuses to change for a tuner
that were previously defined (except if the tuner_addr is set), this were
making eeprom tuner detection useless.
This patch removes tuner type setup from saa7134-i2c, moving it to the proper
place, after taking eeprom into account.
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (452 commits)
V4L/DVB (7731): tuner-xc2028: fix signal strength calculus
V4L/DVB (7730): tuner-xc2028: Fix SCODE load for MTS firmwares
V4L/DVB (7729): Fix VIDIOCGAP corruption in ivtv
V4L/DVB (7728): tea5761: bugzilla #10462: tea5761 autodetection code were broken
V4L/DVB (7726): cx23885: Enable cx23417 support on the HVR1800
V4L/DVB (7725): cx23885: Add generic cx23417 hardware encoder support
V4L/DVB (7723): pvrusb2: Clean up input selection list generation in V4L interface
V4L/DVB (7722): pvrusb2: Implement FM radio support for Gotview USB2.0 DVD 2
V4L/DVB (7721): pvrusb2: Restructure cx23416 firmware loading to have a common exit point
V4L/DVB (7720): pvrusb2: Fix bad error code on cx23416 firmware load failure
V4L/DVB (7719): pvrusb2: Implement input selection enforcement
V4L/DVB (7718): pvrusb2-dvb: update Kbuild selections
V4L/DVB (7717): pvrusb2-dvb: add DVB-T support for Hauppauge pvrusb2 model 73xxx
V4L/DVB (7716): pvrusb2: clean up global functions
V4L/DVB (7715): pvrusb2: Clean out all use of __FUNCTION__
V4L/DVB (7714): pvrusb2: Fix hang on module removal
V4L/DVB (7713): pvrusb2: Implement cleaner DVB kernel thread shutdown
V4L/DVB (7712): pvrusb2: Close connect/disconnect race
V4L/DVB (7711): pvrusb2: Fix race on module unload
V4L/DVB (7710): pvrusb2: Implement critical digital streaming quirk for onair devices
...
|
|
Beholder TV/FM tuners:
Changes:
Add support Beholder Columbus PCMCIA card.
Add key map for remote control of Beholder Columbus PCMCIA card.
Fix gpiomask for all Beholder tuners.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There are two conditions, reported by saa7134 that indicates that the I2C bus
is busy: TO_SCL and TO_ARB.
On both states, it needs to wait for I2C release, before using the bus.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Some DVB-S boards, i.e. with the SD1878 tuner, use a 4 MHz reference frequency.
This reqires a different setup of the clock PLL.
This patch adds an enum to the tda10086_config struct and sets the proper
values for the boards.
This patch also fixes the DVB-S section of the MD7134_BRIDGE_2
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The adapter_nr module options can be used to allocate static adapter
numbers on a driver level. It avoids problems with changing DVB apapter
numbers after warm/cold boot or device unplugging and repluging.
Each driver holds DVB_MAX_ADAPTER long array of the preferred order of
adapter numbers.
options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a
reversed allocation of adapter numbers.
With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If
both are already in use it will allocate the lowest free adapter number.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Acked-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
If frontend is not attached, both cx88-dvb and saa7134-dvb don't
register DVB. However, dvb unregister were inconditionally called.
Due to that, an OOPS is generated.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Add support for composite and s-video inputs on
Avermedia DVB-S Pro and DVB-S Hybrid+FM cards
(both labled A700) to the saa7134 driver.
XC2028 support for Hybrid+FM is still missing.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Thanks to timf <timf@iinet.net.au>, "Richard (MQ)" <osl2008@googlemail.com> and
gian luca rasponi <lucarasp@inwind.it> for their tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Update Kconfig for the hybrid devices recently converted
to use tuner-simple rather than dvb-pll.
dvb-bt8xx no longer uses dvb-pll at all, so remove all
references to dvb-pll within that driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Convert cx88-dvb and saa7134-dvb to use tuner-simple instead of dvb-pll
for Philips TUV1236D
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Convert saa7134-dvb to use tuner-simple instead of dvb-pll for Philips TD1316
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Convert cxusb, cx88-dvb and saa7134-dvb to use tuner-simple instead of
dvb-pll for Philips FMD1216ME
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Removed unnecessary VIDIOC_G_PRIORITY validation.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Adds a consistency check to avoid OOPS, if tuner_callback priv argument is
NULL. Also, simplifies callback codes on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The pointer transferred directly points to the saa7134_dev
structure
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The ISL6405 LNB supply is used on several Creatix / Medion cards. But only
the MD8800 needs its second section. So don't start it unless it is needed.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch fixes reported problems when trying to add a 9th device into a
system.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Tuner refactoring broke support of tuners with LNA configurations 1 and 2
for both, analog TV and DVB-T.
Additionally, this patch initializes the saa713x gpios defined by the gpiomask
at driver init to avoid undefined stated at dvb.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There are some restrictions:
- The 2nd DVB-S section will only work if the 1st is configured for DVB-S too.
so "options saa7134-dvb use_frontend=0,1" won't work.
- Currently it is not possible to set the higher LNB supply voltages, so
14V instead of 13V in the 2nd section.
- It is not possibe to turn off the 2nd LNB supply independently.
This comes from the problem that the 2nd section can't access the i2c interface
of the LNB supply chip.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
In the case of an access error to the high latency registers of
the audio DSP, the interface needs to be cleared, otherwise a cascade
of errors occurs.
This patch is closely modeled after a proposal by Mirek Slugen
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
If left in blank, the driver will use value 0 (Temic PAL)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Tuner addresses were incorrect. Fix the entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
TUNER_PHILIPS_ATSC is an ambiguous name for a tuner. Rename it to
TUNER_PHILIPS_FCV1236D to be more descriptive.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
tuner-xc2028 needs to know when a DVB module is sharing the same analog tuner.
This is done by comparing a magic number that needs to be the same on analog
and on digital. To make easier, this magic number is a pointer to some data
struct.
With the previous code, two different pointers were using, causing a
miss-detection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch adds support for the following saa7134 xc3028 based boards:
132 -> AVerMedia Cardbus TV/Radio (E506R) [1461:f436]
133 -> AVerMedia Hybrid TV/Radio (A16D) [1461:f936]
134 -> Avermedia M115 [1461:a836]
135 -> Compro VideoMate T750 [185b:c900]
This is based on a original patch thanks to Markus Rechberger that added xc3028
gpio init code for the above boards.
This patch moves saa7134_tuner_callback to saa7134-cards, originally used only
by tda8290 DVB-S boards. The callback was made more generic to support other
tuners.
Currently, it supports both tda8290 and xc2028/xc3028 tuners. Added also the
basis for xc5000 tuner callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
videobuf-dma-sg does not need to depend on PCI. Switch it to using generic
DMA API, convert all affected drivers, relax Kconfig restriction, improve
compile-time type checking, fix some Coding Style violations while at it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Russell Kliese <russell@kliese.wattle.id.au>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The I2C bus interface of the LNB supply sits behind the i2c gate of the
tda10086, so wrappers were necessary for the set_voltage functions.
For the time being, the board will show up as MD8800
Many thanks to Hermann Pitton for his help
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Support is not complete yet and untested.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
saa7134_board_init2()
There are several parts of saa7134_board_init2() that calls tuner modules. We
should first load tuner, otherwise, the commands will fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This also has some coding style fixes.
Signed-off-by: Yuri Funduryan <yurifun@mail.ru>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Adrian Pardini <pardo.bsso@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.
This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
videobuf functions at close() method already locks videobuf. It makes no sense
to keep the locking at empress close() method.
There is also a lock at open() method. I'm not sure if it is safe to remove the
locking there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This helps to identify where vb_lock is being used, and find missusages of the
locks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
saa7134-dvb: add missing dvb_attach around tda10046_attach
This patch adds a possibly missing dvb_attach for tda10046_attach.
This removes the hard dependency of saa7134-dvb on tda1004x module.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Thanks to Angelo Lisco for his initial patch we missed and to
Ahmet Dogan Ugurel confirming such a device functional.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This adds support for analog inputs and DVB-T.
Good sensitivity for DVB-T currently needs to use analog TV first.
DVB-S support is not yet completed, but is on the way.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
It also enumerates now the separate composite input at first
and adds mute ability to radio and external audio-in.
Many thanks to Daftcho Tabakov for reporting the flaws and testing.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
S-Video is unconfirmed, but likely correct.
The remote is not yet investigated.
Thanks go to Sioux for providing code and asking to fix the auto
detection.
Signed-off-by: sioux <sioux_it@libero.it>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Thanks go to Mark Schultz for the initial contribution and to
Dean Hilkewich for testing it again.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|