Age | Commit message (Collapse) | Author |
|
- minor whitespace cleanups
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Added new ID for different revision of card #58. It's the same card,
but with a tda8275a instead of a tda8275
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Add remote.
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- In the rare event that a 333MHz i2c firmware load fails after
writing some data, this fix makes the driver reset the DL_ADDR
registers to the proper values before continuing on with 100MHz
transfers.
Signed-off-by: Tyler Trafford <tatrafford@comcast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Corrected Thomson DTT 7611 tuner programming, based on spec sheet
- renamed to Thomson DTT 761x
- applies to DTT 7611 7611A 7612 7613 7613A 7614 7615 7615A
(DTT 7610 is similar, but slightly different programming)
- corrected frequency ranges for analog and digital modes
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Replace del_timer with del_timer_sync
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Fixes sub-device release for BTTV. Without this, DVB modules can't be reloaded
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- V4L2_(G|S|TRY)_FMT returned incorrect VBI start lines for PAL-M,
NTSC-JP, and PAL-60. They also returned an inaccurate VBI offset.
- V4L2_(G|S)_FMT and V4L2_TRY_FMT disagreed about the start of VBI
capturing in PAL and SECAM second field. Note the start line fixes
may break applications using VIDIOCSVBIFMT because this ioctl fails
when the driver does not support exactly the requested parameters.
- V4L2_TRY_FMT did not clear the reserved field in struct
v4l2_vbi_format.
- V4L2_(S|TRY)_FMT did not expect very large or small VBI start or
count values, returning wrong (but safe) counts due to an overflow.
- VIDIOCGVBIFMT confused V4L and V4L2 VBI flags. However this had no
effect because the flags have the same value and bttv never sets
them.
- In v4l_compat_translate_ioctl() the VIDIOC(G|S)VBIFMT code did not
expect V4L2 drivers supporting VBI formats besides V4L2_PIX_FMT_GREY.
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Debug message changed to be coherent with other modules
- added ntsc parameter
- parameters moved to the beginning at the file
- tuner_status moved to a better position.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Now, default control values at cx88_cx8800_ctls are honored
- default value for contrast/saturation were changed to be
in line with available documentation for the chipset;
- Removed some bad coding at set_control;
- U/V Saturation now changes proportionally
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- "Philips 1236D ATSC/NTSC dual in" - fix typo.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Merged ir-kbd-gpio into bttv as bttv-input, for consistency with other
input modules
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
Updates to the tveeprom eeprom checking
Signed-of-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Replaces MAX()/MIN() by kernel.h max()/min() macros
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- This patch makes kernel in sync with v4l subsystem tree.
- some lines reordered to be sync.
- some reduntant codes removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- some uneeded #if were introduced by a previous patch.
this patch removes these.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- include reorder to be in sync with V4L tree
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Enable remote control on AVERTV STUDIO 303
- This patch adapted from a patch found on a website posted by
an anonymous user. Thanks to original anonymous author for
creating this patch. Tested successfully by George Gazurkoff.
Signed-off-by: George Gazurkoff <gazurkoff@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Fix incorrect matching of TV standards leading to incorrect IFPCoff values.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Set the tuner takeover point to 0x10 for NTSC/radio and 0x14 for PAL/SECAM.
- Allow override through TDA9887_SET_CONFIG
- PAL-N belongs with PAL-BG as does PAL-H. PAL-Nc belongs to PAL-M
- Add SECAM-BGH
- Set video freq to cVideoIF_38_90 for DK standards.
- Add cTunerGainLow to radio, change deemphasis to 75 for mono.
- Add ntsc module param for 'M' and 'J' (Japanese) standards.
- Fix module handling for 2.4.
- Now able to select all standards through pal/secam/ntsc module options
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Add missing VIDEO_ADV_DEBUG config option.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- This patch adds eeprom awareness for the Roslyn. In effect, the
blackbird will query the tuner V4L2_STD_xxxx definitions to determine
whether it's connected to a NTSC or PAL tuner. Based on that, various
default values will change for blackbird encoding.
- Fixes back panel SVIDEO/COMPOSITE with audio, work properly.
- Fixes a problem with lip sync issues, due to bad framerate vs
audio rate assumptions.
- Fixed a problem with the GPIO configuration in cx88-cards.
- Removed the comments in cx88-cards that made no sense.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
This patch replace all calls to pci_module_init, that's deprecated and
will be removed in future, with pci_register_driver that should be
the used function now.
Signed-off-by: Otavio Salvador <otavio@debian.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Cleaned up the structure to use the V4L2_STD_xxx definitions
rather than a one off set of hardcoded values - which could
change in the future.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Remove AUDC_CONFIG_PINNACLE horror. This also fixes radio support
for mt20xx tuners.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Removes obsoleted stuff
- Reorders some stuff to make it clearer to read
- Clears some debug messages
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Mark tda9887.c status log values as hexadecimal (add 0x prefix).
Add VIDIOC_LOG_STATUS support to tuner-core.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Fix compile error (missing '}') in em28xx-video.c. Remove dead code and
volume scaling from msp3400.c. Volume scaling does not belong there, it should
be done in the driver for the card that uses the msp3400 if needed, not in the
msp3400.c source. The volume scaling code gave problems with the ivtv driver
which does not need to do any scaling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Controls now come from video and audio decoder driver for msp3400 and tvp5150.
- Added audio and sound controls as provided by msp3400 and tvp5150.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Add support for another Nova-T-PCI PCI subdevice 0x9001
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Cleanup check for dvb.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
products.
- Add support for the Hauppauge HVR1100 and HVR1100-LP products.
- Add i2c_gate_ctrl callback function to dvb_frontend_ops struct.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Added a new debug msg to help identifying tuner Problems
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- added offset parameter for adjusting tuner offset by hand
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Fix gcc-4.0.2 compile error in msp3400.c.
- msp_attach moved to reduce a prototype.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Change function order to reduce usage of function
prototypes.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Fix wrong tuner.h define for tuner 46 (it's a Panasonic, not a Microtune).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Tuner description now follows the same CodingStyle as the others
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Video IF was removed from tuners struct.
- Each Video standard have its own Video IF frequency, so it
is related to video standard. Of course tuner also needs
saw filters for IF, but this way, similar tuners can be grouped
into just one entry, if they have the same cut-off freqs and
the same switch config and global config.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Add support for KWorld DVB-S 100, based on the same chips as Hauppauge
Nova-S Plus (CX23883/CX24123/CX24109), without the Intersil ISL6421,
which is used for LNB control.
- LNB voltage and tone are controled by LNBDC and LNBTone bits from
register 0x29 of the CX24123 demodulator.
- The MO_GP0_IO register from CX23883 is used to turn LNB power on and off.
Signed-off-by: Vadim Catana <skystar@moldova.cc>
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Enable IR support for the Nova-S-Plus.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Added V4L support for the Nova-S-Plus and Nova-SE2 DVB-S products.
- Basic DVB-S support is working, analog video inputs work.
- It has one or two fixme comments, primarily analog GPIOs (audio) and eeprom parsing.
- CX24123 code (in cx88-dvb.c) disabled until the
- cx24123 module is added to dvb-kernel cvs.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Modifications to bttv to support the Hauppauge ImpactVCB product
(Model #64900).
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Added "TerraTec Cinergy 250 PCI" board (tv and radio).
- svideo not tested
- IR yet not working
Signed-off-by: Jörg Schummer <joerg.schummer@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Added SECAM L' video standard
- Common std macros moved to videodev2.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- This patch fixes merge and typo problems in v4l2/compat, and fixes
VIDIOC_STREAMON, VIDIOC_STREAMOFF & VIDIOC_S_FBUF.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Adds 32-bit compatibility for v4l2 framegrabber ioctls.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- 64-bit fixes for removing warnings on compat_ioctl32.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- Another build fix for compat_ioctl32.c
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|
|
- More build fixes for compat_ioctl32.c
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
|