aboutsummaryrefslogtreecommitdiff
path: root/drivers/mfd
AgeCommit message (Collapse)Author
2010-03-07mfd: Introduce remove_script function for twl4030Mike Turquette
New function twl4030_remove_script(u8 flags) takes a script type as defined in twl.h and prevents any script already loaded in that position from running. This is accomplished by programming SEQ_ADD_* to 0x3f, the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags. (Future) users of this function include OMAP board files for machines facing a race condition between sleep and warm reset. Signed-off-by: Mike Turquette <mturquette@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd/mmc: SDHI Kconfig updateMagnus Damm
Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM processors. While at it, make CONFIG_TMIO_MMC depend on CONFIG_MFD_SH_MOBILE_SDHI. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: sh_mobile_sdhi MMC_CAP_MMC_HIGHSPEED supportMagnus Damm
Add MMC_CAP_MMC_HIGHSPEED support to the sh_mobile_sdhi driver. Also, remove type cast and FIXME comment. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add WM831x revision B supportMark Brown
Revision B of the WM831x devices changes the sense of the tristate bit for GPIO configuration, inverting it to become an enable instead. Take account of this in the gpiolib driver. A current sink regulation status bit has also been added in revision B, add a flag indicating if it's present but don't use it yet. This revision also adds an interrupt on key up for the ON pin event which the existing code is able to take advantage of. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add twl6030 base addr for ID0, ID1, ID2Balaji T K
Add base address for generic slave ID0, ID1, ID2 and introduced one more entry to align RTC module number between twl4030 and twl6030 Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Disable TWL4030/5030 I2C1/I2C4 internal pull-upsMoiz Sonasath
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to use only the external HW resistor >=470 Ohm for the assured functionality in HS mode. While testing the I2C in High Speed mode, it was discovered that without a proper pull-up resistor, there is data corruption during multi-byte transfer. RTC(time_set) test case was used for testing. From the analysis done, it was concluded that ideally we need a pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for assured performance in HS mode. Signed-off-by: Moiz Sonasath <m-sonasath@ti.com> Signed-off-by: Allen Pais <allen.pais@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Introduce lpc_sch for Intel SCH LPC bridgeDenis Turischev
Intel Poulsbo (SCH) chipset LPC bridge controller contains several functions. Creating and MFD driver for the LPC bridge controller allows simultaneous use of SMBus and GPIO interfaces on the SCH. Signed-off-by: Denis Turischev <denis@compulab.co.il> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Check for ACPI conflictsSamuel Ortiz
For ACPI based systems, we should check for ACPI conflicts when adding the platform devices. The test will always succeed for non ACPI platforms. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Fix twl_has_pwrbutton typoEduardo Valentin
Change the typo CONFIG_INPUT_TWL4030_PWBUTTON_MODULE in the twl_has_pwrbutton definition to CONFIG_INPUT_TWL4030_PWRBUTTON_MODULE. Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com> Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Use genirq in 88pm860xHaojian Zhuang
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the touchscreen driver of 88pm860x since IRQ handling is changed. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Fix WM8994 error handlingJoonyoung Shim
This patch fixes wrong goto statement for error handling on probe. Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Use i2c_dummy in 88pm860xHaojian Zhuang
Use i2c_dummy in 88pm860x driver to avoid using static in probe function. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Update irq handler in max8925Haojian Zhuang
Update thread irq handler. Simply the interface of using thread irq. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Update i2c driver for max8925Haojian Zhuang
Update I2C driver in order to fit all of three I2C components in max8925. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Program twl4030 remap_sleep correctlyMike Turquette
Variable remap was incorrectly referencing remap_off for the remap_sleep case when configuring TWL4030 power scripts. Signed-off-by: Mike Turquette <mturquette@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add initial WM8994 supportMark Brown
The WM8994 is a highly integrated ultra low power audio hub CODEC. Since it includes on-board regulators and GPIOs it is represented as a multi-function device, though the overwhelming majority of the functionality is provided by the ASoC CODEC driver. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: htc-i2cpld depends on GPIOLIBRandy Dunlap
htc-i2cpld should depend on GPIOLIB, otherwise there are many build errors: drivers/mfd/htc-i2cpld.c:50: error: field 'chip_out' has incomplete type drivers/mfd/htc-i2cpld.c:54: error: field 'chip_in' has incomplete type drivers/mfd/htc-i2cpld.c:243: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:243: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:278: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:278: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:282: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:282: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:315: error: dereferencing pointer to incomplete type drivers/mfd/htc-i2cpld.c:322: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:322: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:467+: error: dereferencing pointer to incomplete type [19X] drivers/mfd/htc-i2cpld.c:490: error: implicit declaration of function 'gpiochip_add' drivers/mfd/htc-i2cpld.c:504: error: implicit declaration of function 'gpiochip_remove' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Remove leftover from discontinued TWL4030 battery patchChristoph Egger
The TWL4030_BCI_BATTERY config option originates from a patch to the omap git tree. However inclusion in linux was seemingly rejected and the functionality nears inclusion under a different name so this removes the bits of the old version that made it into the mainline kernel again. Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Fix debugfs code in AB3100 OTP driverLinus Walleij
This fixes the aged and unreachable debugfs code in the AB3100 OTP driver so that it's (A) reachable and (B) works. Bug detected in parallell by Christoph Egger using VAMOS and Robert P. J. Day by his kernel scanning script. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Cc: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Cc: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Use AB3100 MFD core IRQ for interrupt randomnessLinus Walleij
This reintroduces the entropy sampling of the AB3100 IRQ as the IRQF_SAMPLE_RANDOM is going out according to the feature removal schedule. I'm trying to do this the right way then, so CC:ing some random people for a quick review. We add entropy for interrupt events in the AB3100 which are truly random in nature, like external cables being connected, voltages on batteries dropping below certain ranges, ADC triggers or overheating. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Cc: Robin Getz <rgetz@blackfin.uclinux.org> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add HTCPLD driverCory Maccarrone
This change introduces a driver for the HTC PLD chip found on some smartphones, such as the HTC Wizard and HTC Herald. It works through the I2C bus and acts as a GPIO extender. Specifically: * it can have several sub-devices, each with its own I2C address * Each sub-device provides 8 output and 8 input pins * The chip attaches to one GPIO to signal when any of the input GPIOs change -- at which point all chips must be scanned for changes This driver implements the GPIOs throught the kernel's GPIO and IRQ framework. This allows any GPIO-servicing drivers to operate on htcpld pins, such as the gpio-keys and gpio-leds drivers. Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add subdevs in max8925Haojian Zhuang
Add subdevs in MAX8925. MAX8925 includes regulator, backlight and touch components. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Initial max8925 supportHaojian Zhuang
Basic Max8925 support, which is a power management IC from Maxim Semiconductor. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Append subdev into 88pm860x driverHaojian Zhuang
Append backlight, led & touch subdevs into 88pm860x driver. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add irq support in 88pm860xHaojian Zhuang
88PM860x is a complex PMIC device. It contains touch, charger, sound, rtc, backlight, led, and so on. Host communicates to 88PM860x by I2C bus. Use thread irq to support this usage case. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Rename 88pm8607 to 88pm860x in mfdHaojian Zhuang
Rename 88PM8607 to 88PM860X in both Makefile and Kconfig under mfd directory. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Support 88pm8606 in 860x driverHaojian Zhuang
88PM8606 and 88PM8607 are two discrete chips used for power management. Hardware designer can use them together or only one of them according to requirement. There's some logic tightly linked between these two chips. For example, USB charger driver needs to access both chips by I2C interface. Now share one driver to these two devices. Only one I2C client is identified in platform init data. If another chip is also used, user should mark it in companion_addr field of platform init data. Then driver could create another I2C client for the companion chip. All I2C operations are accessed by 860x-i2c driver. In order to support both I2C client address, the read/write API is changed in below. reg_read(client, offset) reg_write(client, offset, data) The benefit is that client drivers only need one kind of read/write API. I2C and MFD driver can be shared in both 8606 and 8607. Since API is changed, update API in 8607 regulator driver. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Split 88pm8607 driverHaojian Zhuang
Create 88pm8607-i2c driver to support all I2C operation of 88PM8607. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Convert AB3100 driver to threaded IRQLinus Walleij
This converts the AB3100 core MFD driver to use a threaded interrupt handler instead of the explicit top/bottom-half construction with a workqueue. This saves some code and make it more similar to other modern MFD drivers. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Don't allow WM8350 to be built modularMark Brown
The genirq implementation does not allow modules to implement irq_chips so the conversion of WM8350 to genirq means we can no longer allow the driver to be built as a module. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Convert WM8350 to genirqMark Brown
This gives us use of the diagnostic facilities genirq provides and will allow implementation of interrupt support for the WM8350 GPIOs. Stub functions are provided to ease the transition of the individual drivers, probably after additional work to pass the IRQ numbers via the struct devices. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add a data argument to the WM8350 IRQ free functionMark Brown
To better match genirq. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Correct use after free for t7l66xbJulia Lawall
The structure t7l66xb should not be freed before the subsequent references to its fields in the arguments to clk_put. Furthermore, this structure is allocated near the beginning of the function, and a goto to the label err_noirq appears after a successful allocation, so it would seem that the kfree should be moved down below this label. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,e; identifier f; iterator I; statement S; @@ *kfree(x); ... when != &x when != x = e when != I(x,...) S *x->f // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk>
2010-03-07mfd: Use resouce_size for tc6393xbH Hartley Sweeten
Use resource_size() for ioremap. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Use resource_size() for t7l66xbH Hartley Sweeten
Use resource_size() for ioremap. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Use resource_size() in sm501H Hartley Sweeten
The requested memory region is smaller than the actual ioremap(). Use resource_size() to get the correct size. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-06mfd/mc13783: new function reading irq mask and status registerUwe Kleine-König
The driver for the mc13783 rtc needs to know if the TODA irq is pending. Instead of tracking in the rtc driver if the irq is enabled provide that information, too. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: Valentin Longchamp <valentin.longchamp@epfl.ch> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06mc13783: rename mc13783_{{un,}mask,ack_irq} to have a mc13783_irq prefixUwe Kleine-König
In the source file group these functions together. The mc13783 header file provides fallback implementations for the old names to prevent build failures. When all users of the old names are fixed to use the new names these can go away. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: Valentin Longchamp <valentin.longchamp@epfl.ch> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06bitops: rename for_each_bit() to for_each_set_bit()Akinobu Mita
Rename for_each_bit to for_each_set_bit in the kernel source tree. To permit for_each_clear_bit(), should that ever be added. The patch includes a macro to map the old for_each_bit() onto the new for_each_set_bit(). This is a (very) temporary thing to ease the migration. [akpm@linux-foundation.org: add temporary for_each_bit()] Suggested-by: Alexey Dobriyan <adobriyan@gmail.com> Suggested-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Artem Bityutskiy <dedekind@infradead.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-01Merge with mainline to remove plat-omap/Kconfig conflictTony Lindgren
Conflicts: arch/arm/plat-omap/Kconfig
2010-03-01Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits) ASoC: Check progress when reporting periods from i.MX FIQ handler ASoC: Remove a unused variables from i.MX FIQ runtime data ALSA: hda - Add/fix ALC269 FSC and Quanta models ALSA: hda - Add ALC670 codec support OMAP4: PMIC: Add support for twl6030 codec ALSA: hda - remove unnecessary msleep on power state transitions usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h ASoC: fsi: Modify over/under run error settlement ASoC: OMAP4: Add McPDM platform driver ASoC: OMAP4: Add support for McPDM ASoC: OMAP: data_type and sync_mode configurable in audio dma ALSA: hda - Add missing description in HD-Audio-Models.txt ALSA: add support for Macbook Air 2,1 internal speaker ALSA: usbaudio: consolidate header files ALSA: usbmixer: bail out early when parsing audio class v2 descriptors ALSA: usbaudio: implement basic set of class v2.0 parser ALSA: usbaudio: introduce new types for audio class v2 ALSA: usbaudio: parse USB descriptors with structs ALSA: hda - enable snoop for Intel Cougar Point ALSA: hda - Remove identical definitions for macmini3 model ...
2010-03-01Merge branch 'topic/asoc' into for-linusTakashi Iwai
2010-02-26V4L/DVB: mfd: Add timb-radio to the timberdale MFDRichard Röjfors
This patch addes timb-radio to all configurations of the timberdale MFD. Connected to the FPGA is a TEF6862 tuner and a SAA7706H DSP, the I2C board info of these devices is passed via the timb-radio platform data. Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com> Cc: sameo@linux.intel.com Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2010-02-26V4L/DVB: timberdale: fix mfd buildRandy Dunlap
Fix mfd/timberdale build error -- add depends GPIOLIB. include/linux/spi/max7301.h:14: error: field 'chip' has incomplete type build-r7353.out:make[3]: *** [drivers/mfd/timberdale.o] Error 1 Repairs commit ff7a26e08a16bb31158d830dbf60db2ff47019ab Author: Richard R<C3><B6>jfors <richard.rojfors@pelagicore.com> AuthorDate: Thu Feb 4 08:18:52 2010 -0300 Commit: Mauro Carvalho Chehab <mchehab@redhat.com> CommitDate: Fri Feb 5 12:25:37 2010 -0200 V4L/DVB: mfd: Add support for the timberdale FPGA Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Richard Rojfors <richard.rojfors@pelagicore.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2010-02-26V4L/DVB: mfd: Add support for the timberdale FPGARichard Röjfors
The timberdale FPGA is found on the Intel in-Vehicle Infotainment reference board russelville. The driver is a PCI driver which chunks up the I/O memory and distributes interrupts to a number of platform devices for each IP inside the FPGA. Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2010-02-24OMAP4: PMIC: Add support for twl6030 codecMisael Lopez Cruz
In order to have TWL6030 CODEC driver as a platform driver, codec data should be passed through twl_platform_data structure. For twl6030 audio codec, the following data may be passed: - audpwron_gpio: gpio line used to power-up/down the codec. A low-to-high transition powers codec up. Setting audpwron_gpio to a negative value means that codec will use manual power sequence instead of automatic sequence - naudint_irq: irq line for audio interrupt. twl6030 drives NAUDINT line to low when an interrupt (codec ready, plug insertion/removal, etc) is detected However, codec driver can operate if any or none of them are passed. Signed-off-by: Misael Lopez Cruz <x0052729@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-02-15omap2: Convert ARCH_OMAP24XX to ARCH_OMAP2Tony Lindgren
Convert ARCH_OMAP24XX to ARCH_OMAP2 Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-09tree-wide: Assorted spelling fixesDaniel Mack
In particular, several occurances of funny versions of 'success', 'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address', 'beginning', 'desirable', 'separate' and 'necessary' are fixed. Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Joe Perches <joe@perches.com> Cc: Junio C Hamano <gitster@pobox.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-01-29mfd: Fix asic3 buildDmitry Artamonow
asic3 also needs tmio_core or otherwise will fail to build. Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-01-18mfd: Unlock mc13783 before subsystems initialisation, at probe time.Alberto Panizzo
With this, mc13783 subsystems drivers can configure the mc13783 chip reading and writing registers. Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-20 06:38:56 +0000