| Age | Commit message (Collapse) | Author |
|---|
|
Minor cleanups for the MMC/SD support on avr32:
- Make at32_add_device_mci() properly initialize "missing"
platform data ... so boards like STK1002 won't try GPIO 0.
- Switch over to gpio_is_valid() instead of testing for only
one designated value.
- Provide STK1002 platform data for the unlikely case that
switches are set so first Ethernet controller isn't in use.
(That's the only way to get card detect and writeprotect
switch sensing on the STK1000.)
And get rid of one "unused variable" warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
atmel-mci: debugfs support
mmc: Add per-card debugfs support
mmc: Export internal host state through debugfs
imxmmc: fix crash when no platform data is provided
imxmmc: fix platform resources
imxmmc: remove DEBUG definition
mmc_spi: put signals to low power off fix
|
|
Create additional files under the host's debugfs directory containing
additional host-specific debug information.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Don't crash if no platform data is provided.
In this case assume that card is present.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Fixup platform resources handling.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Removed DEBUG #define #undef, because module is automaticaly
compiled with -DDEBUG when CONFIG_MMC_DEBUG is defined.
Currently it just generates compiler warning about redefinition.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
alpha:
drivers/mmc/host/sdhci.h:242: error: field 'sg_miter' has incomplete type
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The original intention was to write a zero byte to mmc to force spi
signals to low when doing power off. Somehow the spi_w8r8 call got there
so a read followed the write of single zero byte. This patch changes
that to simple write of zero byte without the following read.
This way the power off is more reliable and completely sufficient.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Improve the PIO handling so that it can service highmem pages.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Commit c8b3e02 renamed a variable, but missed one reference to it
inside a WARN_ON, causing it to incorrectly trigger.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The ADMA code path assumes that the 3 byte alignment fix doesn't cross
a page boundary. I'm not convinced this is worth supporting, but at
least print a warning in the off chance we'll actually see such a request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Ensure that the s3cmci host controller is turned off
when the machine is shutdown, otherwise we end up
leaving the card powered and processing insertion and
removal events after the system prints "System halted."
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Basic suspend/resume support: disable peripheral on suspend and
reinit on resume.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Fix the naming of various functions in the s3cmc
driver to stop triggering section mismatch warnings.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch does a few small cleanups around the atmel mci platform code
and in the atmel-mci driver. The platform changes simply removes an
unused variable, uses the fact that by the end we always have some form
of platform data and notes that GPIO_PIN_NONE != 0. This last point
could cause the incorrect attempt to twice reserve pin PA0.
While we've got the hood up, add linux/err.h to the atmel-mci.c include
list. It needs it and generally pulls it by voodoo but I did once
stumble across a config which don't build.
This is against Linus' latest git.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This comment update got lost in the great floo^Wmerge. As Pierre
pointed out, no one knows what 'CaFe' is.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
1. sdhci_prepare_data: fix shadowing of count variable
u8 count
int count -> sg_cnt;
2. sdhci_add_host: assignment of integer to pointer
dma_mask = 0 -> dma_mask = NULL;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Relax requirements on host controllers and only require that they do not
report a transfer count than is larger than the actual one (i.e. a lower
value is okay). This is how many other parts of the kernel behaves so
upper layers should already be prepared to handle that scenario. This
gives us a performance boost on MMC cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
DMA addresses are not pointers, so don't treat them as such. Avoids
compiler warnings when using 64-bit DMA addresses on a 32-bit system.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch fix warning :shadowing dma variable
and made use of module_param_named instead of module_param
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The hardware does not support any multi-block transfers
with an block-size that is not 32bit aligned. Also the driver
itself does not support single block non-32bit transfers
either.
Ensure that the s3cmci_setup_data() returns the appropriate
error if we encounter this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add better debugging to show where errors are being
generated, as some error codes can come from several
different code paths.
Also fix the error return path from s3cmci_setup_data()
to return the error it returned to the request.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Ensure that we have physical media present before attempting to
send a request to a card. This ensures that we do not get flooded
by errors from commands that can never be completed timing out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
mmc_detect_change() takes jiffies, not msecs. Convert the
previous value of msecs into jiffies before calling.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add MODULE_ALIAS() declerations for all the supported platform
devices for this driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The driver should be checking for a negative error code from
s3c2410_dma_request(), not non-zero. Newer kernels now return
the DMA channel number that was allocated by the request.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add support to the S3C24XX MMC driver to have the card detect be on
a pin that is not IRQ capable.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Fix a crash if host->mrq->data is NULL on ending a transfer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Support for inverting the sense of the MMC driver's write
protect detection line.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch adds platform data support to the s3mci driver. This allows
flexible board-specific configuration of set_power, card detect and read only
pins.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Fix Bug #677 - I/O errors on heavy microSD writes for 2.6.22.x.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
is stopped.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Bugfix to ensure DMA channel allocated is freed on exit.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is a workaround of some S3C2410 MMC chip bug
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This is the latest S3C MMC/SD driver by Thomas Kleffel
with cleanups as suggested by AKPM done by Ben Dooks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Be a bit more robust and fall back to PIO if someone is feeding us
bogus addresses.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.
Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The upcoming JMicron chips will have solved all the currently known
bugs, so don't penalize them for older problems.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The MMC core provides a carddetect poll feature, time to
remove the driver's own implementation of it.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Don't process an MMC request if no card is present.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Clean up the codebase, no functional changes.
- merge the au1xmmc.h header contents into the driver file,
- indentation, spelling and style fixes.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Wire up the SD controllers' SDIO IRQ capability.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Remove the DB1200 board-specific functions (card present, read-only,
activity LED methods) and instead add platform data which is passed
to the driver. This also allows for platforms to implement other
carddetect schemes (e.g. dedicated irq) without having to pollute the
driver code. The poll timer (used for pb1200) is kept for compatibility.
With the board-specific stuff gone, the driver's ->probe() code can be
cleaned up considerably.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The byte mode support fails to clear the byte mode bit in the command
register, possibly leaving byte mode enabled with the counters programmed
in non-byte mode.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
