aboutsummaryrefslogtreecommitdiff
path: root/drivers/mmc/host
AgeCommit message (Collapse)Author
2008-04-18sdhci: improve no card, no reset quirkPierre Ossman
The quirk was meant to just inhibit some resets, but ended up blocking all of them. Fortunately, this was just what was needed. Change the comment to reflect reality. Also, this issue has just been observed on Samsung laptops, so reduce the number of chips the quirk affects. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Do not busy wait for end of command for everJarkko Lavinen
The limit was a fixed 100k limit in the busy loop, which is not accurate. It would better to have time limit for the worst case which occurs when sending 80 cycles at 400 kHz and takes about 200 microseconds, so limit the max time spend in the busy loop for some 250 microseconds. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Start new commands from work queue instead of irqJarkko Lavinen
Use work queues for starting new commands instead of starting them directly from irq handler. The command scheduling needs to be delayed a bit for some cards which should not be done from an interrupt. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Lazy clock shutdownJarkko Lavinen
MMCA spec says the mmc clock should be kept running for at least 8 cycles after the last RW request. Ensure this with lazy clock disable after a request, or with an explicit delay before switching a slot. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Move failing command abortion to workqueueJarkko Lavinen
Abort failed command from workqueue rather than from an interrupt, allowing longer delays in abortion. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Use tasklet instead of workqueue for cover switch notificationJarkko Lavinen
The cover waitqueue is occasionally scheduled twice from timer and the interrupt and oops follows. It would have been possible to fix this problem with spinlocks but using tasklet was a dropin solution with no need for locking. This path also adds some cleanups. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Check the get_cover_state function pointer if not setKyungmin Park
If the get_cover_state is not set, it occurs the oops. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Using setup_timer instead of init_timerCarlos Eduardo Aguiar
Using setup_timer() instead of init_timer() on omap.c file. Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Abort stuck commandsJarkko Lavinen
When a card is removed while it is being accessed, a command can get stuck so that no timeout or end of command interrupt ever occurs. The command getting stuck is almost always CDM12, but also the other commands can get stuck. Catch a stuck command with a timer and try sending the initialization stream until the controller starts running again and responds with the end of command status. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: General cleanup for MMC multislot supportJuha Yrjola
General code cleanup, modifications at some dev_* functions and other hacks at mmc_omap_irq() for MMC multislot support. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Power functions modified to MMC multislot supportJuha Yrjola
Modifications at power functions to MMC multislot support. This patch also move board-specific code out of MMC OMAP driver. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Fix timeout calculation for MMC multislot supportJuha Yrjola
Fix the data timeout calculation for MMC multislot support. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: New release dma and abort xfer functionsJuha Yrjola
New functions to support MMC multislot: mmc_omap_release_dma() and mmc_omap_abort_xfer(). Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Add back cover switch supportJuha Yrjola
This patch adds back MMC cover switch support in a way that supports multiple slots. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Introduce new multislot structure and change driver to use itJuha Yrjola
Introduce new MMC multislot structure and change driver to use it. Note that MMC clocking is now enabled in mmc_omap_select_slot() and disabled in mmc_omap_release_slot(). Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Remove cover switch handling to allow adding multislot supportTony Lindgren
This patch removes the MMC cover switch handling temporarily to make following multislot patches cleaner. MMC cover switch handling will be added back in later patches after adding basic multislot support. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Fix the BYTEBLOCK capability removalFrancisco Alecrim
According with commit 255d01af9a990fd5166f04ed0cc0b30b7b67e81e from Linux-OMAP tree, the BYTEBLOCK capability was removed by Pierre Ossman. MMC_CAP_BYTEBLOCK is not defined causing the compile error: drivers/mmc/host/omap.c: In function `mmc_omap_probe': drivers/mmc/host/omap.c:1077: error: `MMC_CAP_BYTEBLOCK' undeclared (first use in this function) drivers/mmc/host/omap.c:1077: error: (Each undeclared identifier is reported only once drivers/mmc/host/omap.c:1077: error: for each function it appears in.) Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Remove extra divisor increaseTony Lindgren
As noted by Kyungmin Park, the divisor calculation has an unnecessary increase. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Remove some opcodes from host driverCarlos Eduardo Aguiar
This patch removes some opcodes from host driver so there's no need on putting '#include <linux/mmc/mmc.h>', that should not be needed in host drivers. Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18sdhci: allow led to be controlled freelyPierre Ossman
Hook up the controller LED to the LED subsystem, allowing more flexible control than simply indicating an ongoing request. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18sdhci: remove custom controller namePierre Ossman
Remove the use of the sdhci specific device name and use the mmc controller name instead. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-15mmc: fix platform driver hotplug/coldplugKay Sievers
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MMC host platform drivers, to re-enable auto loading. Also, add missing owner declarations in driver init. [dbrownell@users.sourceforge.net: registration fixes] Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-15tifm_sd: DATA_CARRY is not boolean in tifm_sd_transfer_data()Roel Kluin
DATA_CARRY is not boolean Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-08mmc: extend ricoh_mmc to support Ricoh RL5c476Frank Seidel
This patch adds support for the Ricoh RL5c476 chip: with this the mmc adapter that needs this disabler (R5C843) can also be handled correctly when it sits on a RL5c476. Signed-off-by: Frank Seidel <fseidel@suse.de> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08at91_mci: use generic GPIO callsDavid Brownell
Update the AT91 MMC driver to use the generic GPIO calls instead of the AT91-specific calls; and to request (and release) those GPIO signals. That required updating the probe() fault cleanup codepaths. Now there is a single sequence for freeing resources, in reverse order of their allocation. Also that code uses use dev_*() for messaging, and has less abuse of KERN_ERR. Likewise with updating remove() cleanup. This had to free the GPIOs, and while adding that code I noticed and fixed two other problems: it was poking at a workqueue owned by the mmc core; and in one (rare) case would try freeing an IRQ that it didn't allocate. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08sdhci: add num index for multi controllers caseFeng Tang
Some devices have several controllers; need add the index info to device slot name host->slot_desc[] Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08mmc: remove sdhci and mmc_spi experimental markersPierre Ossman
Both of these drivers work well (although some hardware still has its problems) and are not in the "alpha" quality that EXPERIMENTAL suggests. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08mmc: Handle suspend/resume in Ricoh MMC disablerPhilip Langdale
As pci config space is reinitialised on a suspend/resume cycle, the disabler needs to work its magic at resume time. For symmetry this change also explicitly enables the controller at suspend time but it's not strictly necessary. Signed-off-by: Philipl Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-01-28Merge branch 'pxa-plat' into develRussell King
* pxa-plat: (53 commits) [ARM] 4762/1: Basic support for Toradex Colibri module [ARM] pxa: fix mci_init functions returning -1 [ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix [ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270 [ARM] 4746/1: pcm027: network support for phyCORE-PXA270 [ARM] 4745/1: pcm027: default configuration [ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module [NET] smc91x: Make smc91x use IRQ resource trigger flags [ARM] pxa: add default config for littleton [ARM] pxa: add basic support for Littleton (PXA3xx Form Factor Platform) [ARM] 4664/1: Add basic support for HTC Magician PDA phones [ARM] 4649/1: Base support for pxa-based Toshiba e-series PDAs. [ARM] pxa: skip registers saving/restoring if entering standby mode [ARM] pxa: fix PXA27x resume [ARM] pxa: Avoid fiddling with CKEN register on suspend [ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme [ARM] pxa: Add zylonite MFP wakeup configurations [ARM] pxa: program MFPs for low power mode when suspending [ARM] pxa: make MFP configuration processor independent [ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functions ... Conflicts: arch/arm/mach-pxa/ssp.c Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-27i2c/tps65010: move header to <linux/i2c/...>David Brownell
Move the tps65010 header file from the OMAP arch directory to the more generic <linux/i2c/...> directory, and remove the spurious dependency of this driver on OMAP. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-26[ARM] pxa: mmc: add 1st host controller support for pxa3xxBridge Wu
This patchis to add the first mmc controller support for pxa3xx. It's valid for pxa3[0|1|2]0. On zylonite, the first controller supports two slots, this patch only support the first one right now. Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26[ARM] 4711/1: pxa: mmc: move DMA specific code to platform layerBridge Wu
This patch is to move pxamci DMA specific code to corresponding platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes the driver code dedicated to platform which is not extensible. It is applicable to all pxa platforms. Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26[ARM] 4709/1: pxa: mmc: add 26MHz support for pxa3[0|1]0 mmc controllerBridge Wu
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for pxa3[0|1]0. This patch is to add 26MHz support for them. pxa host clock will be set to 26MHz mode when the card supported max clock rate is higher than or equal to 26MHz. Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Acked-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-12-12sdhci: support JMicron JMB38x chipsPierre Ossman
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit aligned (both size and start address). It also doesn't like switching between PIO and DMA mode, so it needs to be reset after each request. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12sdhci: use PIO when DMA can't satisfy the requestPierre Ossman
Some controllers have been designed on the assumption that all transfers will be 32-bit aligned, both in start address and in size. This is not a guarantee the SDHCI specification provides and not one we can provide. Revert back to PIO for individual requests in order to work around the hardware bug. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12sdhci: don't warn about sdhci 2.0 controllersPierre Ossman
We support 2.0 controllers, even though we don't use anything in the new feature set. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12sdhci: describe quirksPierre Ossman
Add a comment for each quirk to describe what it does and why. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-05spi: use simplified spi_sync() calling conventionMarc Pignat
Given the patch which simplifies the spi_sync calling convention, this one updates the callers of that routine which tried using it according to the previous specification. (Most didn't.) Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-21tifm_sd: handle non-power-of-2 block sizesAlex Dubov
It is possible to handle arbitrary block sizes with tifm card reader by conditionally switching to PIO in case such block has to be delivered. At the beginning of each request, DMA is either disabled (non-power-of-2 block size) or set to load time user preference. Signed-off-by: Alex Dubov <oakad@yahoo.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-11-10Add missing "\n" to log messageRolf Eike Beer
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-31[ARM] Fix pxamci regressionRussell King
Fix: WARNING: at arch/arm/mach-pxa/clock.c:69 clk_disable() [<c002d7c8>] (dump_stack+0x0/0x14) from [<c00334f4>] (clk_disable+0x34/0xa0) [<c00334c0>] (clk_disable+0x0/0xa0) from [<c028a43c>] (pxamci_set_ios+0x74/0xf0) [<c028a3c8>] (pxamci_set_ios+0x0/0xf0) from [<c0281548>] (mmc_power_off+0x90/0x9c) [<c02814b8>] (mmc_power_off+0x0/0x9c) from [<c0281a30>] (mmc_start_host+0x18/0x28) [<c0281a18>] (mmc_start_host+0x0/0x28) from [<c02825a0>] (mmc_add_host+0xe8/0x104) [<c02824b8>] (mmc_add_host+0x0/0x104) from [<c028a7d0>] (pxamci_probe+0x24c/0x2f4) [<c028a584>] (pxamci_probe+0x0/0x2f4) from [<c01e5948>] (platform_drv_probe+0x20/0x24) ... Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-29Correction of "Update drivers to use sg helpers" patch for IMXMMC driverPavel Pisa
The previous change omits "data->" prefix in the "data->sg" case. This change fixes kernel compilation. Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> drivers/mmc/host/imxmmc.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
2007-10-27scatterlist fallout: mmcAl Viro
#include <scatterlist/scatterlist.h> is an odd thing to do... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-27mmc_spi: Fix mmc-over-spi regressionDavid Brownell
Patch 49dce689ad4ef0fd1f970ef762168e4bd46f69a3 changed the sysfs data structures for SPI in a way which broke the MMC-over-SPI host driver. This patch fixes that regression by changing the scheme used to keep from knowingly trying to use a shared bus segment, and updates the adjacent comments slightly to better explain the issue. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-27at91_mci: Fix bad referencePierre Ossman
The flags parameter got removed in a previous commit, but some references were overlooked. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-24mmc: sg falloutJens Axboe
Do a full scan of the directory to try and be a bit more proactive, instead of waiting for things to break. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23[PATCH] Fix breakage after SG cleanupsRalf Baechle
Commits 58b053e4ce9d2fc3023645c1b96e537c72aa8d9a ("Update arch/ to use sg helpers") 45711f1af6eff1a6d010703b4862e0d2b9afd056 ("[SG] Update drivers to use sg helpers") fa05f1286be25a8ce915c5dd492aea61126b3f33 ("Update net/ to use sg helpers") converted many files to use the scatter gather helpers without ensuring that the necessary headerfile <linux/scatterlist> is included. This happened to work for ia64, powerpc, sparc64 and x86 because they happened to drag in that file via their <asm/dma-mapping.h>. On most of the others this probably broke. Instead of increasing the header file spider web I choose to include <linux/scatterlist.h> directly into the affectes files. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23mmc: fix sg->page falloutEmil Medve
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-22[SG] Update drivers to use sg helpersJens Axboe
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-17mmc: at91_mci: cleanup: use MCI_ERRORSAndrew Victor
A small MMC driver cleanup. Use the defined AT91_MCI_ERRORS in at91_mci_completed_command() instead of specifying all the error bits individually. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-24 15:04:46 +0000