| Age | Commit message (Collapse) | Author |
|---|
|
controller
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The functions that write the OOB info (on hardware ECC only) use the
HW_SYNDROME method.
This is not correct : the start position is "pos = eccsize + chunk" and
should be eccsize. So, the standard (nand_write_oob_std) function should
be used. This patch corrects this by using NAND_ECC_HW instead of
NAND_ECC_HW_SYNDROME.
This has only been tested on small pages nand flash.
(if anyone can test it on large pages that would be great).
kernel version : 2.6.27-rc2 (current git mtd-2.6)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The ALE signal isn't correctly wired up to the ECC controller on the
AP7000, so it starts calculating ECC during the address cycles.
Work around this by resetting the ECC controller between the address and
data cycles.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This uses __raw_{read,write}s{b,w}() primitives to access data on NAND
chips for more efficient I/O.
On an arm926 with memory clocked at 100 MHz, this reduced the elapsed time
for a 64 MiB read by 16%. ("dd" /dev/mtd0 to /dev/null, with an 8-bit
NAND using hardware ECC and 128KiB blocksize.)
Also some minor section tweaks:
- Use platform_driver_probe() so no pointer to probe() lingers
after that code has been removed at run-time.
- Use __exit and __exit_p so the remove() code will normally be
removed by the linker.
Since these buffer read/write calls are new, this increases the runtime
code footprint (by 88 bytes on my build, after the section tweaks).
[haavard.skinnemoen@atmel.com: rebase onto atmel_nand rename]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Some of them, at least.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This fixes several bugs in the atmel_nand_probe() error path, including
at least one memory leak.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.
Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
