aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/benet/be_cmds.c
AgeCommit message (Collapse)Author
2009-11-23be2net: remove BUG_ON() when be2net runs out of mccq wrbsSathya Perla
The driver can run out of mccq wrbs when completions don't arrive due to an unresponsive card. This must not hit a BUG_ON(); instead log a msg and return an error. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-23be2net: Issue fw_init/clean cmds to fwSathya Perla
These cmds are issued to the fw in probe/resume and remove/suspend paths to help fw execute some initialization and cleanup code. This change needed the be_hw_up() code to be refactored as be_get_config(). Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-23be2net: support configuration of 64 multicast addresses instead of 32Sathya Perla
To send upto 64 addresses in the multicast-set cmd, the non-embeeded cmd format that provides for a bigger buffer is used instead of an embedded format. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20be2net: Patch to flash redboot section while firmware update.Sarveshwar Bandi
Please apply patch to update redboot section while firmware update. Code checks if section needs to be updated before actually doing it. Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-28be2net: Changes to update ethtool get_settings function to return ↵Sarveshwar Bandi
appropriate values. Update ethtool get_settings function to: - get current link speed settings from controller - get port transceiver type from controller - fill appropriate values for supported, phy_address Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-27Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/sh_eth.c
2009-10-14be2net: fix support for PCI hot plugSathya Perla
Before issuing any cmds to the FW, the driver must first wait till the fW becomes ready. This is needed for PCI hot plug when the driver can be probed while the card fw is being initialized. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14be2net: fix promiscuous and multicast promiscuous modes being enabled alwaysSathya Perla
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-12be2net: Implement ethtool get_phys_id function.Sarveshwar Bandi
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-05be2net: Fix a bug in preparation of mcc wrb which was causing flash ↵Ajit Khaparde
operation to fail This patch fixes a bug that got introduced in commit 76998bc7. During preparation of mcc wrb, req was being wrongly overwritten and the flash operation was failing. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30be2net: Workaround to fix a bug in Rx Completion processing.Ajit Khaparde
vtp bit in RX completion descriptor could be wrongly set in some skews of BladEngine. Ignore this bit if vtm is not set. Resending because the previous patch was against net-next tree. This patch is against the net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-17be2net: fix some cmds to use mccq instead of mboxSathya Perla
All cmds issued to BE after the creation of mccq must now use the mcc-q (and not mbox) to avoid a hw issue that results in mbox poll timeout. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-07be2net: Changes to support flashing of the be2 network adapterAjit Khaparde
Changes to support flashing of the be2 network adapter using the request_firmware() & ethtool infrastructure. The trigger to flash the device will come from ethtool utility. The driver will invoke request_firmware() to start the flash process. The file containing the flash image is expected to be available in /lib/firmware/ Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-05be2net: Patch to perform function reset at initializationsarveshwarb
This patch is a bug fix to avoid system going into a bad state when driver is loaded in context of kdump kernel. The patch fixes the issue by performing a soft reset of pci function at probe time. Signed-off-by: sarveshwarb <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-01be2net: delete unnecessary code from be_cmd_POST()Sathya Perla
When the driver loads the POST stage of the card is expected to be POST_STAGE_ARMFW_RDY. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-01be2net: some name changes for consistencySathya Perla
be_mbox_db_ring() has been changed to be_mbox_notify() (to be consistent with be_mcc_notify()) and struct be_mcc_cq_entry changed to be_mcc_compl to be consistent with rx/tx_compl. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-01be2net: replace some printks with dev_err()/dev_warn()Sathya Perla
And get rid of some unnecessary printks. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-01be2net: remove pci_func field from be_adapter structSathya Perla
pci function is available as PCI_FUNC(pdev->devfn); no need for a separate field. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-01be2net: get rid of be_ctrl_info struct/abstractionSathya Perla
Currently only the be_ctrl_info struct ptr (instead of adapter) is passed to all the routines in be_cmds.c. Instead pass be_adapter ptr to allow access to all its fields. Merge the contents of struct be_ctrl_info into be_adapter. The resulting code is simpler. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-19be2net: receive asynchronous link status notifications from BESathya Perla
Rcv and process ansync link status notifications from BE instead of polling for link status in the be_worker thread. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-19be2net: cleanup multicast_set cmd to avoid mc_list copySathya Perla
Cleanup multicast_set method to avoid an extra copy of mc_list and unwanted promiscuos sets to BE. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-19be2net: Use MCC queue for cmds that may be called in BH contextSathya Perla
Currenlty multicast_set and promiscuous_config cmds -- that may be called in BH context -- use the blocking MCC mbox to post cmds. An mbox cmd is protected via a spin_lock(cmd_lock) and not spin_lock_bh() as it is undesirable to disable BHs while a blocking mbox cmd is in progress (and take long to finish.) This can lockup a cmd in progress in process context. So, these two cmds in BH context must use the MCC queue to post cmds. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-19be2net: Add MCC queue mechanism for BE cmdsSathya Perla
Currenlty all cmds use the blocking MCC mbox to post cmds. An mbox cmd is protected via a spin_lock(cmd_lock) and not spin_lock_bh() as it is undesirable to disable BHs while a blocking mbox cmd is in progress (and take long to finish.) This can lockup a cmd in progress in process context. Instead cmds that may be called in BH context must use the MCC queue to post cmds. The cmd completions are rcvd in a separate completion queue and the events are placed in the tx-event queue. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-11net: Add be2net driver.Sathya Perla
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 12:47:30 +0000