| Age | Commit message (Collapse) | Author |
|---|
|
Checkpatch compliance
The latest version of checkpatch found the following style errors in the
code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistakes
Spelling has to L's in it...
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1G LED does not turn off
The 1G LED was not switched to off when the link was lost
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
before other actions (currently it is stopped last and can corrupt
the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
shared per port and which are per function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not dropping packets with L3/L4 checksum error
Those packets should be passed to the OS. The problem is clear in
forwarding mode.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TPA stands for Transparent Packet Aggregation. When enabled, the FW
aggregate in-order TCP packets according to the 4-tuple match and sends
1 big packet to the driver. This packet is stored on an SGL in which
each SGE is 1 page. The FW also implements a timeout algorithm and it
honors all TCP flag, including the push flag as a trigger to halt
aggregation.
After receiving Ben Hutchings comments, we also added ethtool support,
so now, thanks to Ben's patch, when forwarding is enabled, our
aggregation is turned off using the LRO flags.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To avoid race conditions with link up/down and driver up/down - the
statistics handling was re-written in a form of state machine.
Also supporting statistics for 57711
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Supporting the 57711 and 57711E - refers to in the code as E1H. The
57710 is referred to as E1.
To support the new members in the family, the bnx2x structure was
divided to 3 parts: common, port and function. These changes caused some
rearrangement in the bnx2x.h file.
A set of accessories macros were added to make access to the bnx2x
structure more readable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This new initialization code supports the 57711 HW. It also supports
the emulation and FPGA for the 57711 and 57710 initializations values
(very small amount of code which is very helpful in the lab - less
than 30 lines).
The initialization is done via DMAE after the DMAE block is ready -
before it is ready, some of the initialization is done via PCI
configuration transactions (referred to as indirect write). A mutex
to protect the DMAE from being overlapped was added. There are few
new registers which needs to be initialized by SW - the full comment
for those registers is added to the register file. A place holder for
the 57711 (referred to as E1H) microcode was added- the microcode
itself is too big and it is split over the following 4 patches
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New Link code:
Moving all the link related code (including the calculations, the
initialization of the MAC and PHY and the external PHY's code) into
a separated file. The changes from the code that used to be part of
bnx2x.c (now called bnx2x_main.c) are:
- Using separate structures for link inputs and link outputs to clearly
identify what was configured and what is the outcome
- Adding code to read external PHY FW version and print it as part of
ethtool -i
- Adding code to upgrade external PHY FW from ethtool -E with special
magic number - Changing the link down indication to ERR level
- Adding a lock on all PHY access to prevent an interrupt and
setting changes to overlap
- Adding support for emulation and FPGA (small chunk of code that really
helps in the lab) - Adding support for 1G on BCM8706 PHY
- Adding clear debug print incase of fan failure (the PHY type is now
"failure")
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I would like to thank Eliezer Tamir for writing and maintaining the
driver for the past two years. I will take over maintaining the bnx2x
driver from now on.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several endianity corrections in start_xmit()
Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed locking between fastpath and slowpath operations.
Corrected order of traffic disabling to prevent race when going down
under traffic.
- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC
Got rid of in_reset_task.
Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Errors were summed improperly, some stats were missing.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The configuration of RX filtering needed the following corrections:
Drop flags need to be set per Rx queue.
Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.
Sometimes we failed to detect proper completion due to a logical error
in the wait loop.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Properly protect PHY access between two devices on the same board with
a HW lock.
Use GPIO to clear all previous configurations before changing link
parameters.
Shut down the external PHY in case of fan failure.
Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.
Resolve the flow control response according to autoneg with external
PHY.
Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.
LASI indication fixes to work with peculiarities of PHYs.
Disable MAC RX to avoid a HW bug when closing the MAC under traffic.
Disable parallel detection on HiGig due to HW limitation.
Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct PCI-E info printed by init_one()
In one case it failed to free the netdev.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
