Age | Commit message (Collapse) | Author |
|
Due to a HW issue, our current scheme to transition the connection from
streaming to rdma mode is broken on the passive side. The firmware
and driver now support a new transition scheme for the passive side:
- driver posts rdma_init_wr (now including the initial receive seqno)
- driver posts last streaming message via TX_DATA message (MPA start
response)
- uP atomically sends the last streaming message and transitions the
tcb to rdma mode.
- driver waits for wr_ack indicating the last streaming message was ACKed.
NOTE: This change also bumps the required firmware version to 4.3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The chip executes microcode present in internal RAM,
whose content is loaded from EEPROM on power cycle.
This patch allows an update of the microcode through PIO
without forcing a power cycle.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update FW to 4.1.
Proceed to subsequent HW tuning to improve RDMA perfs..
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Streamline sge page management.
Fix dma mappings when buffers are recycled.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use the right register to stop broadcast/multicast traffic.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix variables initialization and usage in the MAC watchdog.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Rx traffic needs to be halted when the MTU is changed
to avoid a potential chip hang.
Reset/restore MAC filters around a MTU change.
Also fix the pause frames high materwark setting.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Check all lanes for link status on direct XAUI cards.
Don't assume that direct XAUI always uses XGMAC 1.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix netpoll handler to work with line interrupt, msi and msi-x.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
eth_type_trans() now sets skb->dev.
References to skb->dev should happen after it is called.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Many drivers had code that did kill_vid, but they weren't doing vlan
filtering. With new API the stub is unneeded unless device sets
NETIF_F_HW_VLAN_FILTER.
Bad habit: I couldn't resist fixing a couple of nearby style things
in acenic, and forcedeth.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages. We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message. This plugs some close races between the uP and
HW. Also update the minimum required firmware version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
|
|
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the quite common 'skb->h.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the quite common 'skb->nh.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove assumption that PHY interrupts use GPIOs 3 and 5.
Deal with PHY interrupts connected to any GPIO pins.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Reuse the incoming skb when a clientless abort req is recieved.
The release of RDMA connections HW resources might be deferred in
low memory situations.
Ensure that no further activity is passed up to the RDMA driver
for these connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove specific CPL handler.
Add missing CPL handler.
Add missing register setting when the interface is brought up.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The MAC watchdog was failing if the peer interface was brought down.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix a deadlock when the interface s configured down and
the watchdog tack is sleeping on rtnl_lock.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Introduce FW micro version.
Bump up FW version to 3.3.0
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Run the watchdog task when the link is up.
Flush the XGMAC Tx FIFO when the link drops.
Also remove a statistics update that should have gone
in the previous modification of xgmac.c.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Differentiate NIC only adapters from RNICs.
Initialize offload capabilities for RNICs only.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Ensure that the TCAM active region size is at least 16.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
T3B2 does not lose its pcie config space on reset.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Under rare conditions, the MAC might hang while generating a pause frame.
This patch fine tunes the MAC settings to avoid the issue, allows for
periodic MAC state check, and triggers a recovery if hung.
Also fix one MAC statistics counter for the rev board T3B2.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The driver attempts to upgrade the FW if the card has the wrong version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Limit ethtool -g/-G to the given port's queues.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a "-ko" tag to the driver version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Populate Rx free list with pages.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Improve the traffic recovery after the HW ran out of response queue entries.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Offload packets may be DMAed long after their SGE Tx descriptors are done
so they must remain mapped until they are freed rather than until their
descriptors are freed. Unmap such packets through an skb destructor.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update FW version to 3.2
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Clean up some private ioctls.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sysfs attributes are now managed per port, no longer per adapter.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix copyrights in the cxgb3 driver.
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users in -mm.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes the usage of sysfs attributes in cxgb3 for the -mm tree.
It is built against the driver commited in the -mm tree.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Dual licensing, needed for OFED 1.2
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|