aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/e1000e
AgeCommit message (Collapse)Author
2008-08-07e1000e: remove inapplicable test for ioportBruce Allan
There are currently no devices supported by the e1000e driver which need ioport resources, remove the test for it and all unnecessary code associated with it (struct e1000_adapter elements, local variables, etc.) Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-07e1000e: fix drv load issuesJesse Brandeburg
a few people seem to have problems maintaining gigabit link and it was root caused to an interaction between the managability firmware on the host and the driver, not communicating. The form of communication they use is the drv_load bit. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-07e1000e: perform basic 82573 EEPROM checks for known issuesAuke Kok
82573 EEPROMs have been shipped out with known issues. While most people will never see the issues some people do and we know how to address them. Warn the user if we find one of these EEPROM issues. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-07e1000e: convert ndev_ printks to something smallerJeff Kirsher
The ndev_* printk's are too lenghty and we don't need to specify the adapter/netdev struct at all, making this a lot more readable. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-26dma-mapping: add the device argument to dma_mapping_error()FUJITA Tomonori
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER architecture does: This enables us to cleanly fix the Calgary IOMMU issue that some devices are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423). I think that per-device dma_mapping_ops support would be also helpful for KVM people to support PCI passthrough but Andi thinks that this makes it difficult to support the PCI passthrough (see the above thread). So I CC'ed this to KVM camp. Comments are appreciated. A pointer to dma_mapping_ops to struct dev_archdata is added. If the pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's NULL, the system-wide dma_ops pointer is used as before. If it's useful for KVM people, I plan to implement a mechanism to register a hook called when a new pci (or dma capable) device is created (it works with hot plugging). It enables IOMMUs to set up an appropriate dma_mapping_ops per device. The major obstacle is that dma_mapping_error doesn't take a pointer to the device unlike other DMA operations. So x86 can't have dma_mapping_ops per device. Note all the POWER IOMMUs use the same dma_mapping_error function so this is not a problem for POWER but x86 IOMMUs use different dma_mapping_error functions. The first patch adds the device argument to dma_mapping_error. The patch is trivial but large since it touches lots of drivers and dma-mapping.h in all the architecture. This patch: dma_mapping_error() doesn't take a pointer to the device unlike other DMA operations. So we can't have dma_mapping_ops per device. Note that POWER already has dma_mapping_ops per device but all the POWER IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device argument. [akpm@linux-foundation.org: fix sge] [akpm@linux-foundation.org: fix svc_rdma] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix bnx2x] [akpm@linux-foundation.org: fix s2io] [akpm@linux-foundation.org: fix pasemi_mac] [akpm@linux-foundation.org: fix sdhci] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix sparc] [akpm@linux-foundation.org: fix ibmvscsi] Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Muli Ben-Yehuda <muli@il.ibm.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Avi Kivity <avi@qumranet.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-23e1000e: fix e1000_netpoll(), remove extraneous e1000_clean_tx_irq() callIngo Molnar
Evgeniy Polyakov noticed that drivers/net/e1000e/netdev.c:e1000_netpoll() was calling e1000_clean_tx_irq() without taking the TX lock. David Miller suggested to remove the call altogether: since in this callpah there's periodic calls to ->poll() anyway which will do e1000_clean_tx_irq() and will garbage-collect any finished TX ring descriptors. This fix solved the e1000e+netconsole crashes i've been seeing: ============================================================================= BUG skbuff_head_cache: Poison overwritten ----------------------------------------------------------------------------- INFO: 0xf658ae9c-0xf658ae9c. First byte 0x6a instead of 0x6b INFO: Allocated in __alloc_skb+0x2c/0x110 age=0 cpu=0 pid=5098 INFO: Freed in __kfree_skb+0x31/0x80 age=0 cpu=1 pid=4440 INFO: Slab 0xc16cc140 objects=16 used=1 fp=0xf658ae00 flags=0x400000c3 INFO: Object 0xf658ae00 @offset=3584 fp=0xf658af00 Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18igb/ixgbe/e1000e: resolve tx multiqueue bugJeff Kirsher
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling netif_tx_start_all_queues() before calling netif_tx_wake_all_queues(). This causes an issue during loading of the driver. In addition, updated e1000e to use the updated tx mutliqueue api. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-16netdrv intel: always enable VLAN filtering except in promiscous modePatrick McHardy
Currently VLAN filtering is enabled when the first VLAN is added. Obviously before that there's no point in receiving any VLAN packets. Now that we disable VLAN filtering in promiscous mode, we can keep the VLAN filters enabled the remaining time. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-16netdrv intel: disable VLAN filtering in promiscous modePatrick McHardy
As discussed in this thread: http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html promiscous mode means to disable *all* filters. Currently only unicast and multicast filtering is disabled. This patch changes all Intel drivers to also disable VLAN filtering. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-06netdrv: don't truncate VLAN TCI with VLAN strippingPatrick McHardy
The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field for priority mappings, don't truncate the upper 4 bits. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-28Merge branch 'davem-next' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
2008-06-28e1000e: make ioport freeTaku Izumi
This patch makes e1000e driver ioport-free. This corrects behavior in probe function so as not to request ioport resources as long as they are not really needed. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-28Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/wireless/iwlwifi/iwl4965-base.c
2008-06-27e1000e: fix EEH recovery during reset on PPCJeff Kirsher
EEH is not recovering in a reasonable amount of time on PPC during e1000e_down(). Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-11e1000e: allow VLAN devices to use TSO and TCP CSUM offloadJeff Kirsher
Using the new interface for propagating device feature flags into VLAN devices, turn on TSO and CSUM offload on VLAN devices. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22e1000e: use resource_size_t, not unsigned long, for phys addrsBecky Bruce
The use of unsigned long causes the driver to fail on 32-bit systems which support 64-bit resources. Signed-off-by: Becky Bruce <becky.bruce@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06e1000e: don't return half-read eeprom on errorKok, Auke
On a read error, e1000e might have returned uninitialized block of eeprom data back to userspace. The convention is that 0xff is "empty", so mark the entire eeprom as empty in case of an error. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06e1000e: Add support for BM PHYs on ICH9Bruce Allan
This patch adds support for the BM PHY, a new PHY model being used on ICH9-based implementations. This new PHY exposes issues in the ICH9 silicon when receiving jumbo frames large enough to use more than a certain part of the Rx FIFO, and this unfortunately breaks packet split jumbo receives. For this reason we re-introduce (for affected adapters only) the jumbo single-skb receive routine back so that people who do wish to use jumbo frames on these ich9 platforms can do so. Part of this problem has to do with CPU sleep states and to make sure that all the wake up timings are correctly we force them with the recently merged pm_qos infrastructure written by Mark Gross. (See http://lkml.org/lkml/2007/10/4/400). To make code read a bit easier we introduce a _IS_ICH flag so that we don't need to do mac type checks over the code. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25e1000e: Increment version to 0.2.1Jesse Brandeburg
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25e1000e: save and restore pcie/msi state to support EEH recoveryWendy Xiong
To enable EEH support for pci-express network adapters, pcie/msi state needs to be saved and restored for that adapter. Tested this EEH patch with 2ports and 4ports pci-express e1000e adapters. Signed-off-by: Wendy Xiong <wendyx@us.ibm.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25e1000e: lower ring minimum size to 64Auke Kok
The lower limit of 80 descriptors in the ring is only valid for one older 8254x chipset. All e1000e devices can use as low as 64 descriptors. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25e1000e: Fix HW Error on es2lan, ARP capture issue by BMCDavid Graham
Several components to this complex fix. The es2lan cards occasionally gave a "HW Error" especially when forcing speed. Some users also reported that the BMC stole ARP packets. The fixes include setting the proper SW_FW bits to tell the BMC that we're active and not do any un-initialization at all, so the setup routine is largely changed. Signed-off-by: David Graham <david.graham@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25e1000e: Add interrupt moderation run-time ethtool interfaceAuke Kok
The ethtool -c / -C interface can now be used to modify the irq moderation algorithm. This change does not require an adapter reset and can thus be used at all times. The adapter only supports changing/reading rx-usecs which has special values for 0, 1 and 3: 0 - no irq moderation whatsoever 1 - normal moderation favoring regular mixed traffic (default) 3 - best attempt at low latency possible at cost of CPU For values between 10 and 10000 the rx-usecs defines "the minimum time between successive irqs" in usec, unlike the module parameter. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25e1000e: cleanup several stats issuesBruce Allan
Several stats registers are completely unused and we just waste pci bus time reading them. We also omit using the high 32 bits of the GORC/ GOTC counters. We can just read clear them and only read the low registers. Mii-tool can also break es2lan if it executes a MII PHY register ioctl while the device is in autonegotiation. Unfortunately it seems that several applications and installations still perform this ioctl call periodically and especially in this crucial startup time. We can fool the ioctl by providing fail safe information that mimics the "down" link state and only perform the dangerous PHY reads once after link comes up to fill in the real values. As long as link stays up the information will not change. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16e1000e: reformat register test code, fix some minor initializationBruce Allan
The register tests should be run with all the proper flags enabled to maximize the test coverage code and make sure we are as close as we can get to testing regular traffic. Reformat the code for readability. Minor cleanups in the descriptor ring setup. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16e1000e: rename a few functionsJeff Kirsher
Several minor cosmetic function renames. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16e1000e: Make arrays out of these Rx/Tx registersJeff Kirsher
With multiple queues coming into the code these base control registers need to be made into arrays. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16e1000e: limit EEPROM size accessesJeff Kirsher
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-03-28e1000e: reorganize PHY and flow control interfaceJeff Kirsher
This reorganization moves the PHY status into a separate struct. Flow Control setup is moved into this struct as well and frame size away from here into the adapter struct where its inly use is. The post-link-up code is now a separate function and moved out of the watchdog function itself. This allows us to track the es2lan restart issue a bit easier. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-28e1000e: rename mc_addr_list_updateJeff Kirsher
Rename this function to be consistent with function naming (verb first) Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-28e1000e: reformat comment blocks, cosmetic changes onlyBruce Allan
Adjusting the comment blocks here to be code-style compliant. no code changes. Changed some copyright dates to 2008. Indentation fixes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-26e1000e: remove irq_semJesse Brandeburg
irq_sem can safely be removed by auditing all irq.*able sites to make sure that interrupts don't get enabled unexpectedly when the interface is down. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-26e1000e: remove no longer used e1000e_read_nvm_spiAuke Kok
This function is no longer used now that 82573 uses the eerd read method as well. Thanks to Adrian Bunk for pointing this out. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24e1000e: remove unused read value in ASPM disable code.Auke Kok
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24e1000e: fix spelling errors in commentsAuke Kok
Fix some spelling errors and inconsistencies in comment blocks. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24e1000e: fix flow control denial of service possibilityJesse Brandeburg
this patch avoids a denial of service from an evildoer sending a continuous stream of flow control at our adapter that is plugged into a non-flow control enabled switch. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24e1000e: fix flow control when using ethtool overridesJesse Brandeburg
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24e1000e: fix link up message to show ethX:Jesse Brandeburg
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24e1000e: 82573 can use eerd method to read eepromAuke Kok
This simplifies the 82571/2/3 family initialization a bit and removes an initialization table no longer needed. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15e1000e: PCIe devices do not need to unset MANC_ARP_ENADavid Graham
Users reported that ARP's were lost with e1000e. The problem is fixed by not enabling this manageability configuration bit. None of the release_manageability code is actually needed as the normal device reset during a shutdown returns everthing to the right condition automatically. Signed-off-by: David Graham <david.graham@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15e1000e: Fix CRC stripping in hardware context bugAuke Kok
CRC stripping was only correctly enabled for packet split recieves which is used when receiving jumbo frames. Correctly enable SECRC also for normal buffer packet receives. Tested by Andy Gospodarek and Johan Andersson, see bugzilla #9940. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11e1000e: Fix logic reversal keeping link activeAuke Kok
A logic mishap caused the adapter to keep link while we can disable it due to WoL not being active, and vice versa. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-03e1000e: tweak irq allocation messagesAndy Gospodarek
There's too much noise on systems that don't support MSI. Let's get rid of a few and make the real error message more specific. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03e1000e: make a function staticAdrian Bunk
This patch makes the needlessly global reg_pattern_test_array() static. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03e1000e: add new wakeup cababilitiesMitch Williams
Ethtool supports wake-on-ARP and wake-on-link, and so does the hardware supported by e1000e. This patch just introduces the two. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28e1000e endianness annotationsAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28[E1000E]: convert register test macros to functionsJoe Perches
Add functions for reg_pattern_test and reg_set_and check Changed macros to use these functions Compiled x86, untested Size decreased ~2K old: $ size drivers/net/e1000e/ethtool.o text data bss dec hex filename 14461 0 0 14461 387d drivers/net/e1000e/ethtool.o new: $ size drivers/net/e1000e/ethtool.o text data bss dec hex filename 12498 0 0 12498 30d2 drivers/net/e1000e/ethtool.o Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28[E1000E]: update netstats traffic counters realtimeAuke Kok
formerly e1000/e1000e only updated traffic counters once every 2 seconds with the register values of bytes/packets. With newer code however in the interrupt and polling code we can real-time fill in these values in the netstats struct for users to see. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28e1000/e1000e: Move PCI-Express device IDs over to e1000eAuke Kok
e1000e will from now on support the PCI-Express adapters that previously were supported by e1000. This support means better performance and easier debugging from now on for both the old PCI-X/PCI hardware and PCI-Express adapters. This patch also moves 3 recently merged device IDs over to e1000e that are identical to quad-port versions of already existing dual port versions. With this last bit every former e1000 pci-e device should work now with e1000e. Here is a brief list of which gigabit driver to use with which adapter: e1000: 82540 -> 82547 e1000e: 82571 -> 82573 ich8, ich9 (82562 or 82566) es2lan (80003eslan) igb: (not yet merged, only available from e1000.sf.net) 82575 Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28e1000e: Disable L1 ASPM power savings for 82573 mobile variantsAuke Kok
L1 ASPM link (pci-e link power savings) has significant benefits (~1W savings when link is active) but unfortunately does not work correctly on any of the chipsets that have 82573 on mobile platforms which causes various nuisances: - eeprom reads return garbage information leading to bad eeprom checksums - long ping times (up to 2 seconds) - complete system hangs (freeze/lockup) A lot of T60 owners have been plagued by this, but other mobile solutions also suffer from these symptoms. Disabling L1 ASPM before we activate the PCI-E link fixes all of these issues at the cost of some power consumption. Remove a workaround RDTR adjustment that is no longer needed with this new one. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>