aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/e1000e
AgeCommit message (Collapse)Author
2010-01-23net: Fix IPv6 GSO type checks in Intel ethernet driversSridhar Samudrala
Found this problem when testing IPv6 from a KVM guest to a remote host via e1000e device on the host. The following patch fixes the check for IPv6 GSO packet in Intel ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set when packets are forwarded from a guest. Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23e1000/e1000e: don't use small hardware rx buffersJesse Brandeburg
When testing the "e1000: enhance frame fragment detection" (and e1000e) patches we found some bugs with reducing the MTU size. The 1024 byte descriptor used with the 1000 mtu test also (re) introduced the (originally) reported bug, and causes us to need the e1000_clean_tx_irq "enhance frame fragment detection" fix. So what has occured here is that 2.6.32 is only vulnerable for mtu < 1500 due to the jumbo specific routines in both e1000 and e1000e. So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but is not vulnerable to the original issue reported. It has been pointed out that this vulnerability needs to be patched in older kernels that don't have the e1000 jumbo routine. Without the jumbo routines, we need the "enhance frame fragment detection" fix the e1000, old e1000e is only vulnerable for < 1500 mtu, and needs a similar fix. We split the patches up to provide easy backport paths. There is only a slight bit of extra code when this fix and the original "enhance frame fragment detection" fixes are applied, so please apply both, even though it is a bit of overkill. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20e1000e: enhance frame fragment detectionJesse Brandeburg
Originally patched by Neil Horman <nhorman@tuxdriver.com> e1000e could with a jumbo frame enabled interface, and packet split disabled, receive a packet that would overflow a single rx buffer. While in practice very hard to craft a packet that could abuse this, it is possible. this is related to CVE-2009-4538 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()Roel Kluin
The variable count and i are unsigned so the (<|>=)0 tests do not work. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: workaround link issues on busy hub in half duplex on 82577/82578Bruce Allan
This patch removes a delay in hardware after every received packet allowing more time for transmitted packets to go out in between received packets in half duplex. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: MDIO slow mode should always be done for 82577Bruce Allan
A previous 82577 workaround that set the MDIO access speed to slow mode for every PHY register read/write when the cable is unplugged should instead set the access mode to always be slow before any PHY register access. Since the mode bit gets cleared when the PHY is reset, set the mode after every PHY reset. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: fix and commonize code for setting the receive address registersBruce Allan
Fix e1000e_rar_set() to flush consecutive register writes to avoid write combining which some parts cannot handle. Update e1000e_init_rx_addrs() to call the fixed e1000e_rar_set() instead of duplicating code. Also change e1000e_rar_set() to _not_ set the Address Valid bit if the MAC address is all zeros. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: e1000e_enable_tx_pkt_filtering() returns wrong valueBruce Allan
e1000e_enable_tx_pkt_filtering() will return a non-zero value if the driver fails to enable the manageability interface on the host for any reason; instead it should retun zero to indicate filtering has been disabled. Also provide a single exit point for the function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: perform 10/100 adaptive IFS only on parts that support itBruce Allan
Adaptive IFS which involves writing to the Adaptive IFS Throttle register was being done for all devices supported by the driver even though it is not supported (i.e. the register doesn't even exist) on some devices. The feature is supported on 8257x/82583 and ICH/PCH based devices, but not on ESB2. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: don't accumulate PHY statistics on PHY read failureBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: call pci_save_state() after pci_restore_state()Bruce Allan
Due to a change in pci_restore_state()[1] which clears the saved_state flag, the driver should call pci_save_state() to set the flag once again to avoid issues with EEH (same fix that recently was submitted for ixgbe). [1] commmit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-18e1000e: LED settings in EEPROM ignored on 82571 and 82572Bruce Allan
Do not override the customizable LED configuration set in the EEPROM. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-08e1000e: only perform ESB2 MDIC workaround on certain configurationsBruce Allan
A workaround added for all ESB2 devices (adds a delay for all MDIC accesses which resolves an issue with the MDIC ready bit being set prematurely) is applicable only to devices in which the MAC-PHY interconnect is not operating in a certain mode with in-band MDIO. Check the control register for the operating mode and enable the workaround accordingly. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-08e1000e: replace incorrect use of GG82563_REG macroBruce Allan
The GG82563_REG() macro should not be used to determine the offset provided to the e1000e_[read|write]_kmrn_reg() functions since the first argument to the macro is already implied and gets masked off anyway in the functions. The resultant register reads/writes with this patch are functionally the same as before. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-08e1000e: minor correction to name of bit in CTRL_EXT registerBruce Allan
Bit 7 in the CTRL_REG register is actually the Software Definable Pin 3, not the Software Definable Pin 7. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03drivers/net: Move && and || to end of previous lineJoe Perches
Only files where David Miller is the primary git-signer. wireless, wimax, ixgbe, etc are not modified. Compile tested x86 allyesconfig only Not all files compiled (not x86 compatible) Added a few > 80 column lines, which I ignored. Existing checkpatch complaints ignored. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: correct ICH/PCH PHY operations function pointersBruce Allan
Some function pointers for a few PHY operations (for 82578 and 82567) and were set incorrectly causing functions to be executed that were accessing incorrect PHY register offsets for that particular device. This patch also moves a few PHY-specific functions from ich8lan.c to the more appropriate phy.c. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: refactor PHY ID detection workaroundBruce Allan
The workaround that detects the correct PHY ID when an initial read of the PHY ID registers returns an invalid one should retry up to ten times with a small delay between attempts using a single PHY address and then repeat using the remaining possible PHY addresses. Do this instead of trying each possible PHY address repeating that up to 100 times. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: check_polarity function pointers not set for 8257xBruce Allan
The function pointers for 8257x devices are not set. This is not really a problem now because there is nothing in the driver that references the pointers for this particular MAC-family (the appropriate functions are called directly), but the pointers should be set in case they are used in the future. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: remove use of skb_dma_map from e1000e driverAlexander Duyck
In testing we have found that skb_dma_map/unmap is incompatible with HW IOMMU due to the fact that multiple mappings will return different results. In order to correct this we need to remove skb_dma_map/unmap calls from the e1000e driver. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: Use sizeof struct rather than pointer in e1000_get_eeprom()Roel Kluin
Don't use the sizeof the pointer to clear the result Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: PHY type cleanups in e1000e_check_downshift()Bruce Allan
Remove the case for 82577 because it does not support the ability to check for downshift. Add case for e1000_phy_bm which can do this. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: add debug messagesBruce Allan
Add some helpful debug messages. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: comment correctionsBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: enable new 82567V-3 deviceBruce Allan
This new PCI device ID is for a new combination of MAC and PHY both of which already have supporting code in the driver, just not yet in this combination. During validation of the device, an intermittent issue was discovered with waking it from a suspended state which can be resolved with the pre-existing workaround to disable gigabit speed prior to suspending. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: ensure the link state is correct for serdes linksBruce Allan
This patch ensures that the link state (as reported in mac->serdes_has_link) will transition to false when autoneg fails to complete but valid codewords were detected. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: provide family-specific PHY power up/down operationsBruce Allan
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the driver each have their own conditions when the PHY can be powered down. This patch rewrites the PHY power up/down code to fit with the family- specific style used in the driver. All pre-existing calls to power up or down the PHY remain untouched. A new call to power down the PHY when removing the driver when the interface is down replaces the current call to reset the PHY in order to reduce power consumption. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: guard against buffer overflow in cable length tablesBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: provide family-specific functions to manage VLAN filter arraysBruce Allan
The two MAC-families that have VLAN filter table register arrays manage each a bit differently from one another, so provide family-specific functions for managing the register arrays and function pointers to access the appropriate function. Also make sure attempts to access these register arrays are not done on parts not supporting that feature. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-29Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/ieee802154/fakehard.c drivers/net/e1000e/ich8lan.c drivers/net/e1000e/phy.c drivers/net/netxen/netxen_nic_init.c drivers/net/wireless/ath/ath9k/main.c
2009-11-21e1000e: update Tx Unit hang detection messageBruce Allan
The Tx unit hang detection code in e1000e detects other hangs caused by hardware components (e.g. Rx, DMA units), but it is not possible to detect exactly which component is hung so it has always assumed a Tx unit hang. When dumping a message to the system log because of a hang, this patch adds more data to help narrow the cause of the issue and makes the message non-Tx-specific. Because this new code reads PHY registers which can sleep, move it off to a workqueue. This and all previously existing work tasks in the driver are now cancelled when the driver is removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cosmetic - group local variables of the same typeBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: remove redundant might_sleep()Bruce Allan
Now that mutex_lock() calls might_sleep() the driver doesn't have to here. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: do not error out on identification LED init failureBruce Allan
A failure to initialize the identification LED is not a fatal condition and should allow the init path to continue. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: set pm_qos DMA latency requirement per interface when neededBruce Allan
It was pointed out a pm_qos DMA latency requirement set when the driver is loaded when parts that support early receive of jumbo frames are probed could have that requirement overidden if another part supported by the driver (one that does not support early receive of jumbo frames) is probed later. Change the DMA latency requirement to be per-interface if needed instead of per driver. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cleanup functions that clear hardware statisticsBruce Allan
The e1000_clear_hw_cntrs_*() functions read the registers to clear them. There is no reason to save the register contents so the temp variable can be removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cleanup - shift indentation left by exiting early in e1000_tsoBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: set bools to true/false instead of 1/0Bruce Allan
Set booleans to 'true' or 'false' to make it clear it is a boolean. Also change instances of TRUE/FALSE in comments to lowercase true/false. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: provide comment for 82571 workaroundBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: remove comments regarding a non-existent api moduleBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: update copyright informationBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cleanup ops function pointersBruce Allan
The phy and nvm operations structures have function pointers that contain "phy" and "nvm" in the pointer names which are redundant since the structures are already obviously in phy and nvm structures. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: consolidate two dbug macros into one simpler oneBruce Allan
This patch depends on a previous one that cleans up redundant #includes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cleanup redundant #include'sBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: Incorrect MII Link beat reporting.Bruce Allan
The driver was only updating MII stats when an LSC up was detected and the interface had not already been reported up to netdev. This meant MII stats returned in response to an SIOCGMIIREG ioctl would always show a link up if it had ever been up. This was misleading the networking daemon guessnet, which uses this ioctl, into making improper network port selections. This fix adds a call to e1000_phy_read_status() to actively read the mii stats before responding to the SIOCGMIIREG ioctl. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: disable K1 on PCH LOM when in PHY loopback modeBruce Allan
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and 82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise packets might get corrupted. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: improper return code signageBruce Allan
The e1000_get_cable_length_82577() should return a negative value upon error. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: link reporting problemsBruce Allan
Copper links with WoL or management enabled (any condition which prevents the phy from being powered down when the interface is taken down) were always reporting link-up when the interface had been taken down. This is because when the interface is taken down (ifconfig ethx down), interrupts are disabled. With no interrupts, there is no LSC interrupt, which is normally required to set "get_link_status", which instructs the driver to query the device for link state. The fix is to force get_link_status to true if the interface is not up. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: don't clean Rx ring while resettingBruce Allan
When using legacy interrupts, do not clean the Rx ring while resetting otherwise traffic will not pass. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: function pointers for ethtool set/get offloadsBruce Allan
Provide missing function pointers for ethtool set/get offloads. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>