| Age | Commit message (Collapse) | Author |
|---|
|
Currently the media type detection for CX4 adapters lumps them into a
type of fiber. This causes some strange fallout when firmware verification
is done on the NIC, and certain fiber NIC rules get enforced incorrectly.
This patch introduces a new media type for CX4, and puts both 82598 and
82599 CX4 adapters into this bucket.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for CX4 adapters based on 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The packet split feature was recently moved out of the adapter-wide flags
feature field and into a per-Rx ring feature field. In the process, packet
split isn't properly disabled in the Rx ring if the adapter has it globally
disabled, followed by a device reset.
This won't impact the driver today, since it's always in packet split mode.
However, this will prevent any pitfalls if someone disables packet split on
the adapter in the future and doesn't disable it in each ring.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FCoE DDP in 82599 can be used for both FCoE initiator as well as FCoE
target, depending on the indication of the exchange being the responder or
originator in the F_CTL (frame control) field in the encapsulated Fiber
Channel frame header (T10 Spec., FC-FS). For the initiator, OX_ID is used
for FCoE DDP, where for the target RX_ID is used for FCoE DDP.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a simple selection of a FCoE tx queue based on the current cpu id to
distribute transmission of FCoE traffic evenly among multiple FCoE transmit
queues.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for multiple transmit queues to the Fiber Channel
over Ethernet (FCoE) feature found in 82599. Currently, FCoE has multiple
Rx queues available, along with a redirection table, that helps distribute
the I/O load across multiple CPUs based on the FC exchange ID. To make
this the most effective, we need to provide the same layout of transmit
queues to match receive.
Particularly, when Data Center Bridging (DCB) is enabled, the designated
traffic class for FCoE can have dedicated queues for just FCoE traffic,
while not affecting any other type of traffic flow.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
without any cable and reconnecting it to 1G partner
In 82599 multi speed fiber case when driver is loaded without any
cable and reconnecting the cable with a 1G partner does not bring
up the link in 1Gb mode. When there is no link we first setup the link
at 10G & 1G and then try to re-establish the link at highest speed 10G
and thereby changing autoneg_advertised value to highest speed 10G.
After connecting back the cable to a 1G link partner we never try 1G
as autoneg advertised value is changed to link at 10G only. The
following patch fixes the issue by properly initializing the
autoneg_advertised value just before exiting from link setup routine.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disabling the Rx and Tx data arbiters prior to configuration changes,
the arbiters were not being shut down properly. This can create a race
in the DCB hardware blocks, and potentially hang the arbiters. Also, the
Tx descriptor arbiter shouldn't be disabled when applying configuration
changes; disabling this arbiter can cause a Tx hang.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link code cleanup: a number of redundant functions and MAC variables are cleaned up,
with some functions being consolidated into a single-purpose code path.
Removed following deprecated link functions and mac variables
* ixgbe_setup_copper_link_speed_82598
* ixgbe_setup_mac_link_speed_multispeed_fiber
* ixgbe_setup_mac_link_speed_82599
* mac.autoneg, mac.autoneg_succeeded, phy.autoneg_wait_to_complete
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for dcbnl_rtnl_ops.setapp/getapp to set or get the current user
priority bitmap for the given application protocol. Currently, 82599 only
supports setapp/getapp for Fiber Channel over Ethernet (FCoE) protocol.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support to the net_device_ops.ndo_fcoe_enable/disable for 82599. This
consequently allows us to dynamically turn FCoE offload feature on or off
upon incoming calls to ndo_fcoe_enable/disable. When this happens, FCoE offload
features are enabled/disabled accordingly, and this is regardless of whether
DCB being turned on or not.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were already exporting TSO6 to the vlan, but we weren't exporting the
checksum support for IPV6 which was causing warning messages to be
displayed when doing IPv6 TSO over a vlan.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have some ~40 functions that were being called out with 'make
namespacecheck'. This patch changes these functions to be static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix ethtool get_settings logic to report 10G & 1G advertised and
supported link modes in all 8259x 10G backplane connection types
except for 82598EB BX network connection type.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable netdev feature flag bit NETIF_F_FCOE_MTU for 82599 devices and enable
jumbo frame correspondingly when NETIF_F_FCOE_MTU is set.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updates netdev->vlan_features for NETIF_F_FCOE_CRC and NETIF_F_FSO, so that
FCoE CRC and GSO offloads will get used for FCoE over ixgbe based vlan
interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Traffic received with a priority tag (VID = 0) and non-zero priority value was
incorrectly handled by the VLAN packet code path due to a check on zero for
the whole VLAN tag instead of just the VID.
This patch masked out the priority field when checking the vlan tag for
received VLAN packets.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that
have been DDPed. However, it is possible that the length is 0, e.g., for SCSI
READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP
data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed
packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP,
we do not want to return the 0 ddp->len as we want FCP_RSP to be always
delivered to the upper layer. This patch fixes this bug by setting rc only if
ddp->len is non-zero.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/netxen/netxen_nic_main.c
|
|
Currently setting rx-usecs when the interface is in legacy interrupt
mode it is not immediate. We were only setting EITR for each MSIx
vector and since this count would be zero for legacy mode it wasn't
set until after a reset. This patch corrects that by checking what
mode we are in and then setting EITR accordingly.
Signed-off-by: Don Skidmore <donald.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
arch/microblaze/include/asm/socket.h
|
|
For 82599, packet split has to be disabled for FCoE direct data placement.
However, this is only required on received queues allocated for FCoE. This
patch adds a per ring flags to indicate if packet split is disabled on a
per queue basis, particularly for FCoE, as packet split must be disabled
for large receive using direct data placement (DDP).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of passing the register index of the corresponding rx_ring and find
the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(),
simplify the function ixgbe_configure_srrctl() by passing the rx_ring into
it. Then the register index for that rx_ring is already available from
rx_ring->reg_idx.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb priority to vlan-qos egress mapping that can be configured using
set_egress_map with vconfig is overriden by the DCB code in the driver.
This patch allows this existing mechanism to work and will increase the
configuration flexibility of DCB mode on Linux.
A hierarchy of configuration is:
1. Modifies the ixgbe_select_queue() routine for DCB mode to return the
priority value from the VLAN tag. It will normally be zero, unless the egress
priority map has modified it. This will get packets into the correct queue and
result in the queue_mapping field being set correctly.
2. Any tc filter which modifies queue_mapping will be honored, as the filters
are handled after the vlan egress map is handled.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default completion timeout values for 82598 should be in the
range of 50us to 50ms, however the hardware default for these
parts is 500us to 1ms which is less than the 10ms recommended by
the pcie spec. To address this we need to increase the value to
either 10ms to 250ms for capability version 1 configuration, or
16ms to 55ms for version 2.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-3945.h
drivers/net/wireless/iwlwifi/iwl-tx.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
|
|
When a user disables interrupt throttling with ethtool on 82599 devices,
the interrupt timer may not be re-enabled if hardware RSC is running. The
RSC completions in hardware don't complete before the next ITR event tries
to fire, so the ITR timer never gets re-armed. This patch increases the
amount of time between interrupts when throttling is disabled (rx-usecs =
0) when the hardware RSC deature is enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A second set of feature flag bits was added, and the hardware RSC engine
flags were moved there. However, the code itself didn't make the move
completely to use the new bitmap.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our ndo_poll_controller callback is broken for anything but non-multiqueue
setups. This fixes that issue.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an 82599 errata that UDP frames with a zero checksum are
incorrectly marked as checksum invalid by the hardware. This was
leading to misleading hw_csum_rx_error counts. This patch adds a
test around this counter increase for this condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwmc3200wifi/netdev.c
net/wireless/scan.c
|
|
Calls to device_init_wakeup should not be necessary in drivers that use
device_set_wakeup_enable since pci_pm_init will set the can_wakeup flag
for the device when initialized.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain types of control packets (LLDP, LACP, etc.) are not supposed to have a
priority tag or vlan tag inserted. Ixgbe driver is currently priority
tagging everything (if packet is not on a VLAN interface).
This patch modifies DCB mode, so that packets marked with skb priority
TC_PRIO_CONTROL are not priority tagged. It also transmits these packets on
the highest priority traffic class.
Programs (like dcbd) can set the skb priority using a socket option. Or, a tc
filter can be configured to set the priority value. Using the value
TC_PRIO_CONTROL (7) has the benefit that it is already defined in the kernel,
and the bonding LACP code already sets the skb->priority field to this value.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, FCoE offload feature is turned on when the kernel config has
CONFIG_FCOE or CONFIG_FCOE_MODULE set. However, we really want to turn
FCoE offload on when there is FCoE traffic passing and turn it off when
it's just LAN traffic. Since FCoE depends on a lossless network provided
by DCB, this allows us to have FCoE turned on/off when user turns on DCB
using dcbtool.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep the version number marching along as updates come in.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for a new copper device for 82598, device id 0x150b.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the link comes up, the driver detects which flow control settings are
active. This is done using bitwise operations directly from the hardware
registers, and assumes the proper boolean assignment. Make this an
explicit boolean value before assignment to the bool.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool offline test is the only consumer of the legacy descriptors.
Update that path to only use advanced descriptors, and remove all support
for legacy descriptors.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove debug DPRINTK in DCB mode netlink interface.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change clears the address data block memory space, which is needed for
the 82598 which does not have a SAN MAC.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wake-on-lan is currently only supported by 82599 KX4 devices, in all
other cases return a proper value from ixgbe_wol_exclusion function call.
Otherwise from ethtool we will be able to change wol options of
unsupported 8259x devices.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().
I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module. So we
only check if that is the case.
This problem also shows up on Copper devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.
- mdio45_probe call was always failing due to mdio.prtad not being
set. The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0. This will allow us to set the phy_id
and phy.type correctly now.
- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.
- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses three WARN_ON statements from DMA-API debug code
ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.
found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.
in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single
and lastly, don't unmap (half) pages that aren't mapped.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
