aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/qlge
AgeCommit message (Collapse)Author
2009-10-29qlge: Fix firmware mailbox command timeout.Ron Mercer
The mailbox command process would only process a maximum of 5 unrelated firmware events while waiting for it's command completion status. It should process an unlimited number of events while waiting for a maximum of 5 seconds. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-29qlge: Fix EEH handling.Ron Mercer
Clean up driver resources without touch the hardware. Add pci save/restore state. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Add disable/enable firmare irqs to handler.Ron Mercer
This was accidentally omitted from one of the previous patches for firmware event handling. The handler needs to the enable firmware irq mask when it's done processing or it may not get any more events interrupts. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Restore rx mode after internal reset.Ron Mercer
Call set_multi API after reset recovery. This was exposed by tripping tx_timeout. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix chip reset process.Ron Mercer
Add wait for NIC fifo and MGMNT fifo to empty before applying reset. Otherwise broken frames can be processed by management processor and cause it to hang. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix RX multicast filter settings.Ron Mercer
The addresses were being added to the filter properly, but were not being enabled. This adds enable bit to filter write. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix frame routing for multicast frames.Ron Mercer
Broadcast/multicast should always be routed to the default (zeroeth) rx ring. Broadcast frames are already routed correctly. This fixes routing for multicast frames. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix frame routing issue related to bonding.Ron Mercer
Currently frames are routed based on their type and MAC address. This patch adds the port number on which the frame arrived to the routing. This prevents problems in the case where both interfaces have the same MAC address in a routing configuration. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix RSS hashing values.Ron Mercer
Fix RX queue table size and change from random to default hash values. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix lock/mutex warnings.Ron Mercer
Get rid of spinlock and private mutex usage for exclusive access to the HW semaphore register. rtnl_lock already creates exclusive access to this register in all driver API. Add rtnl to firmware worker threads that also use the HW semaphore register. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix queueing of firmware handler in ISR.Ron Mercer
Check that we are not already polling firmware events before we queue the firmware event worker, then disable firmware interrupts. Otherwise we can queue the same event multiple times. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix some bit definitions for reset register.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix error exit for probe call.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Protect reset recovery with rtnl_lock().Ron Mercer
Move the call to rtnl_lock() to before the internal call to ql_adapter_down()/ql_adapter_up(). This prevents collisions that can happen when recovering from an asic error. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix spin_lock warning.Ron Mercer
Remove the unnecessary locking around the call to ql_adapter_reset(). Sep 25 08:17:29 localhost kernel: SOFTIRQ-ON-W at: Sep 25 08:17:29 localhost kernel: [<c0000000000a2964>] .lock_acquire+0x10c/0x158 Sep 25 08:17:29 localhost kernel: [<c0000000004542e0>] ._spin_lock+0x34/0x58 Sep 25 08:17:29 localhost kernel: [<d000000006723070>] .ql_adapter_down+0x40c/0x4a0 [qlge] Sep 25 08:17:29 localhost kernel: [<d0000000067256d8>] .qlge_close+0x38/0x58 [qlge] Sep 25 08:17:29 localhost kernel: [<c0000000003ada6c>] .dev_close+0xdc/0x118 Sep 25 08:17:29 localhost kernel: [<c0000000003adb48>] .rollback_registered+0xa0/0x158 Sep 25 08:17:29 localhost kernel: [<c0000000003adc50>] .unregister_netdevice+0x50/0x7c Sep 25 08:17:29 localhost kernel: [<c0000000003adca0>] .unregister_netdev+0x24/0x40 Sep 25 08:17:29 localhost kernel: [<d00000000672e0c0>] .qlge_remove+0x28/0x64 [qlge] Sep 25 08:17:29 localhost kernel: [<c000000000253fdc>] .pci_device_remove+0x50/0x90 Sep 25 08:17:29 localhost kernel: [<c0000000002f5434>] .__device_release_driver+0x94/0xf8 Sep 25 08:17:29 localhost kernel: [<c0000000002f5560>] .driver_detach+0xc8/0xfc Sep 25 08:17:29 localhost kernel: [<c0000000002f3fd8>] .bus_remove_driver+0xb4/0x114 Sep 25 08:17:29 localhost kernel: [<c0000000002f5d4c>] .driver_unregister+0x80/0xa4 Sep 25 08:17:29 localhost kernel: [<c00000000025421c>] .pci_unregister_driver+0x50/0xc8 Sep 25 08:17:29 localhost kernel: [<d00000000672e044>] .qlge_exit+0x1c/0x34 [qlge] Sep 25 08:17:29 localhost kernel: [<c0000000000ac8b0>] .SyS_delete_module+0x234/0x2d0 Sep 25 08:17:29 localhost kernel: [<c000000000008554>] syscall_exit+0x0/0x40 Sep 25 08:17:29 localhost kernel: INITIAL USE at: Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix out of sync hardware semaphore.Ron Mercer
ql_clear_routing_entries() takes/gives it's own hardware semaphore since it is called from more than one place. ql_route_initialize() should make this call and THEN take it's own semaphore before doing it's work. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix bad bit definitions.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-21trivial: remove unnecessary semicolonsJoe Perches
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-09-01netdev: convert bulk of drivers to netdev_tx_tStephen Hemminger
In a couple of cases collapse some extra code like: int retval = NETDEV_TX_OK; ... return retval; into return NETDEV_TX_OK; Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28qlge: Move TX completions from workqueue to NAPI.Ron Mercer
TX completions were running in a workqueue queued by the ISR. This patch moves the processing of TX completions to an existing RSS NAPI context. Now each irq vector runs NAPI for one RSS ring and one or more TX completion rings. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28qlge: Allow running MSIx with fewer vectors.Ron Mercer
Currently we downshift to MSI/Legacy if we don't get enough vectors for cpu_count RSS rings plus cpu_count TX completion rings. This patch allows running MSIX with the vector count that the platform provides. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28qlge: Get rid of 'default' rx_ring type.Ron Mercer
Currently we have three types of RX rings. 1) Default ring - services rx_ring for broadcast/multicast, handles firmware events, and errors. 2) TX completion ring - handles only outbound completions. 3) RSS ring - handles only inbound completions. This patch gets rid of the default ring type and moves it's functionality into the first RSS ring. This makes better use of MSIX vectors since they are a limited resource on some platforms. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-01qlge: return PCI_ERS_RESULT_DISCONNECT on permanent failureDean Nelson
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for qlge. Signed-off-by: Dean Nelson <dnelson@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix sizeof usage.Ron Mercer
Some usage was only sizing a pointer rather than the data type. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Add/use function for link up/down.Ron Mercer
We need to set/clear the mac address register when the link goes up/down respectively. Without this both ports of a 2-port device can end up with the same mac address in a bonding scenario. The new ql_link_on() and ql_link_off() will also be used in handling certain firmware events. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix MAC address bonding issue.Ron Mercer
This addes functionality to set/clear the MAC address in the hardware when the link goes up/down. The MAC address register is persistent across function resets. In bonding the same address can bounce from one port to the other. This can cause packets to be delivered to the wrong port. This patch clears the MAC address in the hardware when the link is down and sets it when the link comes up. It was found that pulling/pushing the cable from one port to another causes the same MAC address to be in both ports. The next patch in this series will use this functionality as well. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix tx byte counter.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix redundant call to free resources.Ron Mercer
The caller will free acquired resouces if a failure occurs. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix carrier on condition.Ron Mercer
We were turning on the carrier without verifying the link was up. This adds link up to the link initialize check before turning carrier on. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Clear frame to queue routing before reset.Ron Mercer
Not clearing the routing bits can cause frames to erroneously get routed to management processor. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Expand coverage of hw lock for config register.Ron Mercer
The hardware semaphore covers the configuration register as well as the ICB registers. The ICB high and low regs contain the address of the initialization control block and the config register is used to signal the hardware that a block is ready to be downloaded. Currently we were only protecting the ICB regs. This changes expands to cover the config register as well. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-15Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: Documentation/feature-removal-schedule.txt drivers/scsi/fcoe/fcoe.c net/core/drop_monitor.c net/core/net-traces.c
2009-06-12trivial: fix ETIMEOUT -> ETIMEDOUT typosJean Delvare
fix ETIMEOUT -> ETIMEDOUT typos Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-06-12trivial: fix typos s/paramter/parameter/ and s/excute/execute/ in ↵Martin Olsson
documentation and source comments. Signed-off-by: Martin Olsson <martin@minimum.se> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-06-11qlge: Allow RX buf rings to be > than 4096 bytes.Ron Mercer
RX buffer rings can be comprised of non-contiguous fixed size chunks of memory. The ring is given to the hardware as a pointer to a location that stores the location of the queue. If the queue is greater than 4096 bytes then the hardware gets a list of said pointers. This patch addes the necessary logic to generate the list if the queue size exceeds 4096. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-11qlge: Relax alignment on TX harware queue.Ron Mercer
The alignment was on size of queue boundary, but the hardware only requires 4-byte alignment. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: bugfix: Get rid of errant spin_unlock().Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add set TX csum ethtool op.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add support for varied pcie function numbers.Ron Mercer
Currently we support only PCIe NIC functions zero and one, and FCoE functions as 3 and 4. Future configurations can mix these up in any fashion. This patch removes the 0-1 dependancy and allows usage of any of the 4 functions. We also find the alternate NIC function (if exist) and determine our port number based on the comparison of the two functions: Lower function number gets first port, higher function gets second port. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add support for using alternate MAC address.Ron Mercer
Extract either manufacturer or Bladecenter Open Fabric Manager (BOFM) MAC address. BOFM may indicate an alternate MAC address. This patch honors that request by extracting the MAC address from a different flash location if a flag is set. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Drop inbound frames > MTU.Ron Mercer
The max frame size register is set higher than the MTU to accomodate FCoE frames. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Drop inbound error frames.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Remove netif_set_gso_max_size() call.Ron Mercer
Not necessary if hardware supports 65536 as it's the default setting. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add support for retrieving firmware version.Ron Mercer
This is used by driver banner and ethtool info. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix timeout on firmware mailbox commands.Ron Mercer
Some firmware mailbox commands require the firmware to communicate with the FCoE driver running on another PCI function. This can potentially take several seconds. This wait is done in process context only. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix timeout on indexed register wait.Ron Mercer
There are 8 banks of 'sub-registers' each of which are accessed through address/data register pair. An example would be reading flash or the xgmac. Accessing these require the driver to wait for a ready bit before writing the address and then accessing the data. This patch increases the timeout to 100us to prevent timeouts that have been seen on some platforms. These register are accessed in process context only. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix bug in MTU setting process.Ron Mercer
Since an FCoE function shares a port with this NIC function, the jumbo settings must always be in place. This patch causes the hardware to be set up for jumbo if it is not already done. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix bug in firmware event handler.Ron Mercer
Each firmware mailbox command can have a different number of valid data elements. When waiting for a mailbox command to complete it the process passes it's element count and waits for the completion. It is possible that while waiting an unrelated firmware async event (AE) can arrive. When this happens, the handler will over write the element count with the value for the newly arrived AE. This can cause the mailbox command to not get all of it's data. This patch restores original mailbox count at the end of the handler. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix firmware event handler loop.Ron Mercer
Check status on every iteration of event handler loop and exit if an error occurred. If an error occurred then recover process will be queued so this loop should no continue. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29net: dont update dev->trans_start in 10GB driversEric Dumazet
Followup of commits 9d21493b4beb8f918ba248032fefa393074a5e2b and 08baf561083bc27a953aa087dd8a664bb2b88e8e (net: tx scalability works : trans_start) (net: txq_trans_update() helper) Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Multi queue drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers (vxge & tehuti) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-21 23:13:58 +0000