| Age | Commit message (Collapse) | Author |
|---|
|
This patch updates the tg3 version to 3.104.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the 5717 variant device ID enumerations and adds those
DIDs to the PCI ID table.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to funnel each MSI-X vector's rx packet buffers
into a single set of producer rings which will then be submitted to the
hardware.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx producer mailbox registers are used in several spots in the code.
The addition of TG3_64BIT_REG_LOW makes register references
uncomfortably long. This patch creates an alias for the standard and
jumbo ring producer index registers to make the code cleaner.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch increases the number of producer rings available and
implements the constructor and destructor code that deals with them.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes how the code uses the rx_std_prod_idx member. In the
following patch, the code will be changed so that it will act just like
a hardware mailbox. This patch prepares the code so that memory barriers
can be more easily inserted.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A later patch is going to add consumer indicies for the producer rings.
To keep things readable, this patch renames rx_[std|jmb]_ptr to
rx_[std|jmb]_prod_idx.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts the tnapi argument of tg3_alloc_rx_skb() to tp. The
level of indirection is unnecessary.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the tg3_alloc_rx_skb() implementation to accept the
destination producer ring set pointer as a parameter rather than
assuming the source and destination producer rings are the same.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the source index parameter of tg3_alloc_rx_skb(). A
later patch will make it possible for the source and destination
producer rings to be different. This patch opts to make
tg3_alloc_rx_skb() a destination-only implementation and move the code
sensitive to the difference elsewhere.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_get_invariants(), among other things, discovers whether or not
the device is MSI-X capable and how many interrupts it supports.
This discovery needs to happen before registering NAPI instances with
netdev. This patch moves the code block that calls napi_add later in
tg3_init_one() so that tg3_get_invariants() has a chance to run first.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch gives all non-zero MSIX vectors their own NAPI handler. This
will make NAPI handling for those vectors slightly more efficient.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, the 5717 (and future chips) break up PCIe DMA packets across
cacheline boundaries. This isn't necessary on x86. This patch
selectively loosens the restriction.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The A0 revision of the 5717 has problems with short packet fragments.
It needs to use the tg3_start_xmit_dma_bug() routine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 5717 sets up TSO slightly differently in the transmit path. It
looks like this method will be the new way of doing things. This patch
defines a flag to indicate this.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch consolidates the TSO capability discovery code into its own
code block. The code that decides whether or not to allow TSO is then
cleaned up. Finally, the patch consolidates all MSI and MSIX
capability code into a single code block.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need room for another TSO flag and it would be most efficient if it
resided in tg3_flags2. This patch moves the TG3_FLG2_PROTECTED_NVRAM
to tg3_flags3 to make room.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts tg3_start_xmit_dma_bug() to accomodate multiple NAPI
instances. This is prep work for a later patch in this series.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids reprogramming the RCB NIC addresses for all 5755 and
later devices. The address is incorrect for 5717 devices and should be
correct by default for all other affected devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the 5717 phy ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the tg3 version to 3.103.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to disable the TXC and RXC reference clocks if link
is not available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds an RXC auto power-down feature to the code that supports
the gphys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 5785 does not use the RXC reference clock. Turning it off is
desirable as it saves power.
By default, the 50610 enables the RXC reference clock and the 50610M
disables it. Presumably this is one of the reasons why the hardware
architect chose one over the other.
Adding a "rx reference clock disable" flag is not the ideal way to
describe the option, as it would force the MAC using a 50610M to set
the flag. Ideally we want the flags to represent opt-in behavior that
deviates from hardware defaults. Furthermore, the lack of a
"disable" flag implies that the requester wants the rx reference clock
enabled, which doesn't necessarily follow.
By presenting the option as a passive statement (rx reference clock
unused) rather than a command, I hope to convey an opt-in option to
disable the rx reference clock that falls back to hardware defaults if
not set. A secondary benefit of this is that it keeps the
intelligence about phy defaults in the broadcom module where it belongs
and allows the broadcom module more latitude should a bug arise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Auto power-down (APD) support is a power-saving feature. It should be
selectively enabled since it might expose MAC bugs. This patch changes
the code to enable APD only if the PHY_BRCM_AUTO_PWRDWN_ENABLE flag is
set. The tg3 driver was changed to set this bit.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom 50610M parts changed the default definitions of the RGMII mode
shadow register. The 5785 needs the RGMII mode selection bits [4:3]
cleared.
The default value of the remaining bits in this register are zero.
Rather than unnecessarily burn an extra bit in the dev_flags member in
an attempt to enumerate all possible combinations, this patch take a
more course grained approach and labels the option as "clear all bits".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the 50610M phy ID for 5785.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends the loopback test timeout from 250 usec to 350 usec.
When the 5785 is paired against an AC131 phy, the older timeout is
just a little too close to the expected performance based on timings.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch sets the port mode to MII when the link is down for the 5785.
Setting the port mode to MII instead of GMII saves power.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AC131 does not respect the power down bit (bit 11) of the MII
Control Register (reg 0x0). Instead, software is required to put the
phy into standby power down mode through the shadow register set. This
patch implements support for the AC131 standby power down mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch improves 5785 performance by allowing the write DMA engine to
request larger DMA burst sizes than it otherwise would.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to check the status of pci_map_single() before
allowing rx buffers to be used. It also converts the pci_map_single()
call in tg3_run_loopback() to use skb_dma_map() instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prevents a PCIe tx glitch by allowing the transmitter to go
to a low power state.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch renames the PHY_ADDR preprocessor definition. The following
patch will identify a new member on the MDIO bus, so we want this
preprocessor definition to be a little more descriptive.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain power saving conditions, 57780 asic rev devices might
disappear from the system. The fix is to disallow the PCIe PLL from
powering down.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 5906 has trouble with fragments that are less than 8 bytes in size.
This patch works around the problem by pivoting the 5906's transmit
routine to tg3_start_xmit_dma_bug() and introducing a new SHORT_DMA_BUG
flag that enables code to detect and react to the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a flag for each bug workaround in
tg3_start_xmit_dma_bug(). This is prep work for the following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock. The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f6eb9b1fc1411d22c073f5264e5630a541d0f7df, "tg3: Add 5717 asic
rev" changed how the rx return ring size operations are done. It
effectively inverts the sense of the previous test, but it failed to
also invert the resulting sizes. This patch corrects that error.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the tg3 version to 3.102.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 5717 is a dual port chip that has a shared MDIO bus design. While
it is impossible for one function to interface with the wrong phy, that
function still needs to know which MDIO bus address to use when
interfacing with its own phy. This patch adds code to determine which
MDIO bus address to use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds NVRAM detection routines for the 5717.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the 5717 asic rev.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RSS is enabled, the status block format changes slightly. The
"rx_jumbo_consumer", "reserved", and "rx_mini_consumer" members get
mapped to the other three rx return ring producer indexes. This patch
introduces a new per-interrupt member which identifies which location
in the status block a particular vector should look for return ring
updates.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When multivector RSS is enabled, the first interrupt vector is only used
to report link interrupts and error conditions. This patch changes the
code so that rx and tx ring resources are not allocated for this vector.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code needed to enable RSS.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to tune the coalescing parameters for the other
msix vectors.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to enable and disable the rest of the NAPI
instances.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch exposes the additional transmit rings to the kernel and makes
the necessary modifications to transmit, open, and close paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
