| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes the needlessly global function tg3_request_irq()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the netif_carrier_off() call from tg3_init_one()->
tg3_init_link_config() to tg3_open() as is the convention for most other
network drivers.
I was getting a panic after a tg3 device failed to initialize due to DMA
failure. The oops pointed to the link watch queue with spinlock debugging
enabled. Without spinlock debugging, the Oops didn't occur.
I suspect that the link event was getting queued but not executed until
after the DMA test had failed and the device was freed. The link event was
then operating on freed memory, which could contain anything. With this
patch applied, the Oops no longer occurs.
[ Based upon feedback from Michael Chan, we move netif_carrier_off()
to the end of tg3_init_one() instead of moving it to tg3_open() -DaveM ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update version to 3.52.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add fw_version information to ethtool -i.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some nvram related cleanup:
1. Add a tg3_nvram_read_swab() since swabing the data is frequently
done.
2. Add a function to convert nvram address to physical address
instead of doing it in 2 separate places.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethtool memory test on 5787 requires a new memory table.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support one-shot MSI on 5787.
This one-shot MSI idea is credited to David Miller. In this mode, MSI
disables itself automatically after it is generated, saving the driver
a register access to disable it for NAPI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support ipv6 tx csum on 5787 by setting NETIF_F_HW_CSUM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support 5787 hardware TSO using a new flag TG3_FLG2_HW_TSO_2.
Since the TSO interface is slightly different and these chips have
finally fixed the 4GB DMA problem and do not have the 40-bit DMA
problem, a new hard_start_xmit is used for these chips. All previous
chips will use the old hard_start_xmit that is now renamed
tg3_start_xmit_dma_bug().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support additional nvrams and new nvram format for 5787 and 5754.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic support for 2 new chips 5787 and 5754.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix-up tg3_get_ringparam() to return the correct parameters.
Set the jumbo rx ring parameter only if it is supported by the chip
and currently in use.
Add missing value for tx_max_pending, noticed by Rick Jones.
Update version to 3.51.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing netif_running() checks in tg3's dev->set_multicast_list()
and dev->set_mac_address(). If not netif_running(), these 2 calls can
simply return 0 after storing the new settings if required.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update version to 3.50.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support WoL during shutdown by calling
tg3_set_power_state(tp, PCI_D3hot) during tg3_close().
Change the power state parameter to pci_power_t type and use
constants defined in pci.h.
Certain ethtool operations cannot be performed after tg3_close()
because the device will go to low power state. Add return -EAGAIN
in such cases where appropriate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable TSO by default on newer chips that support TSO in hardware.
Leave TSO off by default on older chips that do firmware TSO because
performance is slightly lower.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 5714S and 5715S.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
|
|
|
|
Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.
For example, some 4-port card or mother board designs have 5704 behind
the 5714.
All devices behind the EPB require the 40-bit DMA workaround.
Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID. So add another fallback test, which is the name
of the OBP firmware device tree node. If it's a Sun part we'll
get "network", else it will be named "ethernet".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure tg3_reset_task() is flushed in the close and suspend paths
as noted by Jeff Garzik.
In the close path, calling flush_scheduled_work() may cause deadlock
if linkwatch_event() is on the workqueue. linkwatch_event() will try
to get the rtnl_lock() which is already held by tg3_close(). So
instead, we set a flag in tg3_reset_task() and tg3_close() polls
the flag until it is cleared.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add nvram lock count so that calls to tg3_nvram_lock()/unlock() can
be nested. Add error checking to all callers of tg3_nvram_lock()
where appropriate. To prevent nvram lock failures after halting the
firmware, it is also necessary to release firmware's nvram lock in
tg3_halt_cpu().
Update version to 3.48.
Based on David Miller's initial patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Turning struct iphdr::tot_len into __be16 added sparse warning.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resubmitting after recommendation to use GET_REG32_1() instead of
GET_REG32_LOOP(..., 1). Retested. Problem remains fixed.
Prevent tg3_get_regs() from reading reserved and undocumented registers
at RX_CPU_BASE and TX_CPU_BASE offsets which caused hostile behavior
on PCIe platforms.
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skip the memory 0xb50 to 0x1000 during "ethtool -t" memory test.
Overwriting memory in this region can cause ASF problems.
Update version and release date.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tw32_f() function (register write with immediate read flush) can
hang when used on some registers to switch clock frequencies and
power. A new tw32_wait_f() is added for such registers with the
delay before the read and after the read.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add some missing workarounds in tg3_set_power_state():
1. Workaround to prevent overdrawing current on 5714.
2. Do not power down 5700's PHY because of hw limitation.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Locate the pdev_peer for dual port 5714 NIC devices in addition to
5704 devices. The name is also changed to tg3_find_peer() from
tg3_find_5704_peer(). It is also necessary to call netdev_priv() to
get to the peer's private tg3 structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following bugs in tg3_set_power_state():
1. Both WOL and ASF flags require switching to aux power.
2. Add a missing handshake with firmware to enable WOL.
3. Turn off the PHY if both WOL and ASF are disabled.
4. Add nvram arbitration before halting the firmware.
5. Fix tg3_setup_copper_phy() to switch to 100Mbps when
changing to low power state.
Update revision and date.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the dual-port 5704 is configured as a single-port device with
only one PCI function, it would trigger a BUG() condition in
tg3_find_5704_peer(). This fixes the problem by returning its
own pdev if the peer cannot be found.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix tg3_suspend() and tg3_resume() by clearing and setting the
TG3_FLAG_INIT_COMPLETE flag when appropriate. tg3_set_power_state()
looks at TG3_FLAG_INIT_COMPLETE on the peer device to determine
when to appropriately switch to aux power.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nvram arbitration rules were not strictly followed in a few places
and this could lead to reading corrupted values from the nvram.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[ Move assosciated code comment to the correct spot, and
update driver version and release date -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This one from my DMA_{32,64}BIT_MASK series did not seem to make it
through to upstream.
Use the DMA_{32,64}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
|
|
Update version and reldate and add more sanity checking to
tg3_set_settings().
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Change the ASF heart beat to 5 seconds for faster detection of system
crash. The driver sends the heartbeat every 2 seconds and the ASF
firmware will timeout and reset the device if no heartbeat is received
after 5 seconds. The old scheme of 2 minutes is ineffective.
tg3_write_mem_fast() is added to speed up the IO to send the heartbeat.
When no workaround is needed, it will use direct MMIO to memory space
to write to memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
