| Age | Commit message (Collapse) | Author |
|---|
|
This patch removes the TX and RX flow control flags from tg3_flags and
adds two new flow control variables, flowctrl and active_flowctrl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_nvram_write_block_unbuffered() is reading data from nvram into
allocated buffer before overwriting a part of it with user-supplied
data. Then it feeds the entire page back to nvram. It should be
storing the words it had read as little-endian, not as host-endian.
Note that tg3_set_eeprom() does exactly that for padding the same
data to full words before it gets passed down to tg3_nvram_write_block()
and then to tg3_nvram_write_block_unbuffered().
Moreover, when we get to sending the entire thing back to nvram, we
go through it word-by-word, doing essentially
writel(swab32(le32_to_cpu(word)), ...)
so if we want them to reach the card in host-independent endianness,
we'd better really have all that buffer filled with fixed-endian.
For user-supplied part we obviously do have that (it's an array of
octets memcpy'd in), ditto for padding of user-supplied part to word
boundaries (taken care of in tg3_set_eeprom()). The rest of the
buffer gets filled by tg3_nvram_write_block_unbuffered() and it would
damn better be consistent with that (and with tg3_get_eeprom(), while
we are at it - there we also convert the words read from nvram to
little-endian before returning the buffer to user).
The bug should get triggered on big-endian boxen when set_eeprom is done
for less than entire page. Then the words that should've been unaffected
at all will actually get byteswapped in place in nvram.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed misannotations, introduced a new helper - tg3_nvram_read_le().
It gets __le32 * instead of u32 * and puts there the value converted
to little-endian. A lot of callers of tg3_nvram_read() were doing
that; converted them to tg3_nvram_read_le().
At that point the driver is practically endian-clean; the only remaining
place is an actual bug, AFAICS; will be dealt with in the next patch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the version number to 3.86
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the PHY type reported through ethtool for copper
devices from MII to TP. The latter is more accurate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the A1 revision of 5784, 5764, and 5761, and applies all
previous bugfixes. In places where the list of devices gets too long,
the patch uses a new TG3_FLG3_5761_5784_AX_FIXES flag instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous devices hardcoded the PCI Maximum Read Request Size to 4K. To
better comply with the PCI spec, the hardware now defaults the MRRS to
512 bytes. This will yield poor driver performance if left untouched.
This patch increases the MRRS to 4K on driver initialization.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Internal hardware timers become inaccurate after link events. Clock
frequency switches performed by the CPMU fail to adjust timer
prescalers. The fix is to detect core clock frequency changes during
link events and adjust the timer prescalers accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most 5784 / 5764 LED modes do not work as expected because of a hardware
bug. This patch forces the LED mode to be in MAC LED mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New CPMU devices contend with the GPHY for power management. The GPHY
autopowerdown feature is enabled by default in the PHY and thus needs to
be disabled after every PHY reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the LINK_SPEED mode to the list of CPMU modes that can
cause the loopback tests to fail. These bugs are planned to be fixed in
future revisions of the chip, so the patch qualifies the fixes as such.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer devices contain bootcode in the chip's private ROM area. This
bootcode is called selfboot. Selfboot can be patched in the device's
NVRAM and the patches can have several formats. In one particular
format, the checksum calculation needs to be slightly modified. This
patch adjusts the NVRAM test code for that case, and add support for the
missing formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU
link speed mode is enabled, and the MAC clock is running at 1.5Mhz. The
fix is to run the MAC clock at faster speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle. This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available. When the PHY is powered down, the clock the MAC depends on
is disabled. The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates. The tg3 driver has code to detect this
condition and resets the device during initialization. On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761. However, during this initialization stage, communications
to the APE registers have not yet been set up. The driver then
dereferences a NULL pointer and crashes the machine. The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A reasonably common problem with some devices is that they will
disable MSI generation when the INTX_DISABLE bit is set in the
PCI_COMMAND register.
Quirk this explicitly, guarding the pci_intx() calls in msi.c with
this quirk indication.
The first entries for this quirk are for 5714 and 5780 Tigon3 chips,
and thus we can remove the workaround code from the tg3.c driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch updates the version number to 3.85.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the way the driver works with the PCI command
register. It adjusts the access size from dwords to words. This patch
is done both as a PCI configuration space cleanup and as preparatory
work for PCI error recovery.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch appends the management firmware version to the bootcode
firmware string reported through ethtool.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for upcoming 5723 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
[IPV6]: Consolidate the ip6_pol_route_(input|output) pair
[TCP]: Make snd_cwnd_cnt 32-bit
[TCP]: Update the /proc/net/tcp documentation
[NETNS]: Don't panic on creating the namespace's loopback
[NEIGH]: Ensure that pneigh_lookup is protected with RTNL
[INET]: kmalloc+memset -> kzalloc in frag_alloc_queue
[ISDN]: Fix compile with CONFIG_ISDN_X25 disabled.
[IPV6]: Replace sk_buff ** with sk_buff * in input handlers
[SELINUX]: Update for netfilter ->hook() arg changes.
[INET]: Consolidate the xxx_put
[INET]: Small cleanup for xxx_put after evictor consolidation
[INET]: Consolidate the xxx_evictor
[INET]: Consolidate the xxx_frag_destroy
[INET]: Consolidate xxx_the secret_rebuild
[INET]: Consolidate the xxx_frag_kill
[INET]: Collect common frag sysctl variables together
[INET]: Collect frag queues management objects together
[INET]: Move common fields from frag_queues in one place.
[TG3]: Fix performance regression on 5705.
[ISDN]: Remove local copy of device name to make sure renames work.
...
|
|
This will convert remaining non-obvious or naive calculations of array
sizes to use ARRAY_SIZE() macro.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
A performance regression was introduced by the following commit:
commit ee6a99b539a50b4e9398938a0a6d37f8bf911550
Author: Michael Chan <mchan@broadcom.com>
Date: Wed Jul 18 21:49:10 2007 -0700
[TG3]: Fix msi issue with kexec/kdump.
In making that change, the PCI latency timer and cache line size
registers were not restored after chip reset. On the 5705, the
latency timer gets reset to 0 during chip reset and this causes
very poor performance.
Update version to 3.84.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to read and store sblk->status_tag before checking for more work.
The status tag is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When we detect tx error, it is more correct to return the rx
work_done so far instead of 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update to version 3.83.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables WOL by default if out-of-box WOL is enabled in the
NVRAM.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds rest of the miscellaneous code required to support the
5761.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the new APE block, present in 5761 chips.
APE stands for Application Processing Engine. The primary function of
the APE is to process manageability traffic, such as ASF.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new 5761-specific NVRAM strapping decode routine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I recently noticed that when calling:
# ethtool -s eth0 autoneg on
on a 5722 (though I'm sure it's not specific to that card) that
subsequent checks of the cards status looked like this:
# ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: No <---- This seems odd?!?
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
I noticed that the following commit:
commit 3600d918d870456ea8e7bb9d47f327de5c20f3d6
Author: Michael Chan <mchan@broadcom.com>
Date: Thu Dec 7 00:21:48 2006 -0800
[TG3]: Allow partial speed advertisement.
Honor the advertisement bitmask from ethtool. We used to always
advertise the full capability when autoneg was set to on.
changed things around so that ethtool speed settings were strictly
followed. Unfortunately ethtool doesn't seem to set ADVERTISED_Autoneg
in the advertising field (and maybe it shouldn't have to). I'd vote
that it should be fixed there, but it should also be added here just in
case someone using ethtool ioctls in their own application gets what
they want.
Adding that flag in tg3_set_settings seemed like the most logical place
since the driver works fine on boot. This is just an issue when
re-enabling autonegotiation, so we should probably nip it there.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for 5784 and 5764 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer products change the way the ASIC revision is obtained. This patch
implements how the driver will extract the revision number.
This patch also adds preliminary CPMU support. CPMU stands for Central
Power Management Unit. The CPMU's role is to put the chip into lower
power states when the operating conditions allow it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer tg3 devices shuffle around the registers in PCI configuration
space. This patch changes the way the driver accesses the PCI
capabilities registers. Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed sparse warnings from tg3 driver. The new logic seems fine (I
don't immediately see where we are running over values for any of the
variables that need to be saved).
This patch compiles fine and I'm currently using a tg3 with the patched
driver to post this patch as a basic proof of concept.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A hardware bug was revealed after a recent PCI MSI patch was made to
always disable legacy INTX when enabling MSI. The 5714/5780 chips
will not generate MSI when INTX is disabled, causing MSI failure
messages to be reported, and another patch was made to workaround the
problem by disabling MSI on ServerWorks HT1000 bridge chips commonly
found with the 5714.
We workaround this chip bug by enabling INTX after we enable MSI and
after we resume from suspend.
Update version to 3.81.
This problem was discovered by David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tina Yang <tina.yang@oracle.com> discovered an MSI related problem
when doing kdump. The problem is that the kexec kernel is booted
without going through system reset, and as a result, MSI may already
be enabled when tg3_init_one() is called. tg3_init_one() calls
pci_save_state() which will save the stale MSI state. Later on in
tg3_open(), we call pci_enable_msi() to reconfigure MSI on the chip
before we reset the chip. After chip reset, we call
pci_restore_state() which will put the stale MSI address/data back
onto the chip.
This is no longer a problem in the latest kernel because
pci_restore_state() has been changed to restore MSI state from
internal data structures which will guarantee restoring the proper
MSI state.
But I think we should still fix it. Our save and restore sequence
can still cause very subtle problems down the road. The fix is to
have our own functions save and restore precisely what we need. We
also change it to save and restore state inside tg3_chip_reset() in a
more straight forward way.
Thanks to Tina for helping to test and debug the problem.
[ Bump driver version and release date. -DaveM ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethtool utility function to set or clear IPV6_CSUM feature flag.
Modify tg3.c and bnx2.c to use this function when doing ethtool -K
to change tx checksum.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
