aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath5k/base.c
AgeCommit message (Collapse)Author
2009-02-03Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-01-29ath5k: fix locking in ath5k_configBob Copeland
ath5k_config updates the software context without taking sc->lock. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: support LED's on emachines E510 notebookTulio Magno Quites Machado Filho
Add vendor ID for AMBIT and use it to set the ath5k LED gpio. base.c: Changes-licensed-under: 3-Clause-BSD Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29mac80211: Generic TSF debuggingAlina Friedrichsen
This patch enables low-level driver independent debugging of the TSF and remove the driver specific things of ath5k and ath9k from the debugfs. Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: honor the RTS/CTS bitsBob Copeland
The ath5k driver didn't use set_rts_threshold or use_cts_prot, and also didn't check the IEEE80211_TX_RC_USE_{RTS_CTS,CTS_PROTECT} RC flags. Tell the hardware about these so RTS/CTS will work, and so the device will work better in mixed b/g environments. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: use short preamble when possibleBob Copeland
ath5k previously ignored TX_RC_SHORT_PREAMBLE and did not use config->use_short_preamble, so the long preamble was always used for transmitted packets. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: remove stop/start calls from within suspend/resumeBob Copeland
mac80211 now takes down interfaces automatically during suspend so doing it in the driver is unnecessary. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: fix bf->skb==NULL panic in ath5k_tasklet_rxBob Copeland
Under memory pressure, we may not be able to allocate a new skb for new packets. If the allocation fails, ath5k_tasklet_rx will exit but will leave a buffer in the list with a NULL skb, eventually triggering a BUG_ON. Extract the skb allocation from ath5k_rxbuf_setup() and change the tasklet to allocate the next skb before accepting a packet. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: support LEDs on Acer Aspire One netbookBob Copeland
Add vendor ID for Foxconn and use it to set the ath5k LED gpio and polarity for Acer branded laptops. base.c: Changes-licensed-under: 3-Clause-BSD Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Tested-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29mac80211: clean up set_key callbackJohannes Berg
The set_key callback now seems rather odd, passing a MAC address instead of a station struct, and a local address instead of a vif struct. Change that. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k] Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00] Acked-by: Christian Lamparter <chunkeey@web.de> [p54] Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945] Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-12ath5k: fix return values from ath5k_txBob Copeland
Should return NETDEV_TX_{OK,BUSY} instead of 0,-1 (this doesn't change any current functionality). Changes-licensed-under: 3-Clause-BSD Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19ath5k: correct packet length in tx descriptorsBob Copeland
Packet length calculation (which includes frame check sequence) should take into account whether we add a pad field or not. Extract the calculation into a helper and use it in both places. Changes to desc.c Changes-licensed-under: ISC Changes to ath5k.h, base.c Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19ath5k: fix 802.11 header padding on RX, unpadding on TXBenoit PAPILLAULT
Padding the 802.11 header to a multiple of 4 bytes needs to be done only for frames with a body. This fixes a bug where 2 bytes were missing in monitor mode for ACK frames. Inspired by a patch from Jouni Malinen on ath9k. Ref: http://bugzilla.kernel.org/show_bug.cgi?id=12101 : Signed-off-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-26Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/hp-plus.c drivers/net/wireless/ath5k/base.c drivers/net/wireless/ath9k/recv.c net/wireless/reg.c
2008-11-26ath5k: set mac address in add_interfaceBob Copeland
Configure the mac address in add_interface and clear it in remove_interface so that users can change the mac address to something other than the one in the eeprom. Also avoid setting it at attach time so that we won't ack packets until fully set up. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-25ath5k: name pci driver "ath5k" tooJohannes Berg
Call the ath5k pci driver struct "ath5k" too to be less confusing in sysfs. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-25ath5k: disable beacon filter when station is not associatedMartin Xu
Ath5k driver has too many interrupts per second at idle http://bugzilla.kernel.org/show_bug.cgi?id=11749 Signed-off-by: Martin Xu <martin.xu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21ath5k: allow APs to receive beaconsLuis R. Rodriguez
Allow APs to receive beacons to detect when it needs to use protection to update the NAV correctly on 11b stations. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21ath5k: Fix IMR initNick Kossifidis
*On a previous patch i splitted AR5K_INT_TX to multiple different TX interrupt flags for better handling but i forgot to unmask the new TXDESC and TXEOL interrupts on ath5k_init and only left TXOK. However for each queue we enable TXDESC and TXEOL interrupts, not TXOK so we don't handle TX interrupts at all (because these interrupts remain masked on PISR) and under load it results packet loss. Fix the problem by unmasking TXDESC and TXEOL on ath5k_init. Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-10ath5k: update keycache to support TKIP handlingBob Copeland
Newer parts have slots at entry+64 for michael mic and can do WPA-TKIP in hardware. The open-sourced Atheros HAL has code for accessing this portion so now we know how where to put the key material. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-10ath5k: enable hardware encryption for WEPBob Copeland
This change re-enables hardware encryption for ath5k after setting up mac80211 to handle the initialization vectors which happens to make it work. Add a module param (nohwcrypt) to optionally turn it off. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-06Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/wireless/ath5k/base.c net/8021q/vlan_core.c
2008-11-06Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"John W. Linville
Unfortunately, the result was that mac80211 didn't see all the beacons it actually wanted to see. This caused lost associations. Hopefully we can revisit this when mac80211 is less greedy about seeing beacons directly... This reverts commit 063279062a8c530cc90fb77797db16c49c905b26. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: Update interrupt masking codeNick Kossifidis
*Properly get/set all available ISR/IMR values and review common/uncommon bits *Better handling of per-txq interrupts (we can now resolve what q is generating each interrupt -this will help in debuging wme later) *Some minor updates from legacy-hal *Properly handle RXNOFRM and TXNOFRM interrupt masking (even when we don't set them on IMR they keep showing up, so we disable them by zeroing AR5K_RXNOFRM and AR5K_TXNOFRM registers). This doesn't exist on legacy-hal but i've tested it on various cards and it works fine. Changes-Licensed-under: ISC Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: reduce checkpatch.pl errorsJohn Daiker
A few changes to reduce checkpatch.pl errors in the ath5k driver. For the most part, I only fixed cosmetic things, and left the actual 'code flow' untouched (hopefully)! Diff is against wireless-testing HEAD. Signed-off-by: John Daiker <daikerjohn@gmail.com> Reviewed-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211/drivers: rewrite the rate control APIJohannes Berg
So after the previous changes we were still unhappy with how convoluted the API is and decided to make things simpler for everybody. This completely changes the rate control API, now taking into account 802.11n with MCS rates and more control, most drivers don't support that though. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: fix mesh point operationAndrey Yurovsky
This patch fixes mesh point operation (thanks to YanBo for pointing out the problem): make mesh point interfaces start beaconing when they come up and configure the RX filter in mesh mode so that mesh beacons and action frames are received. Add mesh point to the check in ath5k_add_interface. Tested with multiple AR5211 cards. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: correct ath5k signal qualityLuis R. Rodriguez
This adjusts ath5k's signal quality reporting taking into consideration received beacons at an RSSI of 35 should indicate you can use of 54 Mbps on a single stream card (all ath5k cards) reliably. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31Ath5k: add AP modeJiri Slaby
Add support for AP mode. This involves: - enablement in ath5k_beacon_config -- initialize beacon timer - add AP to the supported modes in ath5k_add_interface - handle beacon change even for AP in ath5k_config_interface - remove useless test for IBSS in ath5k_beacon_update Note that it doesn't enable the AP mode for the driver. It must be enabled by NL80211_IFTYPE_AP bit added to interface_modes. v2: Fixed opmode constant (IEEE80211_ to NL80211_) Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: introduce hw config change flagsJohannes Berg
This makes mac80211 notify the driver which configuration actually changed, e.g. channel etc. No driver changes, this is just plumbing, driver authors are expected to act on this if they want to. Also remove the HW CONFIG debug printk, it's incorrect, often we configure something else. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-29ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA modeBob Copeland
We were setting RX_FILTER_BEACON even after entering STA mode, which leads to a lot of unnecessary wakeups. This should fix the bug "Ath5k driver has too many interrupts per second at idle" at http://bugzilla.kernel.org/show_bug.cgi?id=11749. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-27ath5k: Reset key cache on interface up, thus fixing resumeElias Oltmanns
After a s2ram / resume cycle, resetting the key cache does not work unless it is deferred until after the hardware has been reinitialised by a call to ath5k_hw_reset(). This fixes a regression introduced by "ath5k: fix suspend-related oops on rmmod". Signed-off-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-22ath5k: fix suspend-related oops on rmmodBob Copeland
Based on a patch by Elias Oltmanns, we call ath5k_init in resume even if we didn't previously open the device. Besides starting up the device unnecessarily, this also causes an oops on rmmod because mac80211 will not invoke ath5k_stop and softirqs are left running after the module has been unloaded. Add a new state bit, ATH_STAT_STARTED, to indicate that we have been started up. Reported-by: Toralf Förster <toralf.foerster@gmx.de> Signed-off-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: Bob Copeland <me@bobcopeland.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-06ath5k: implement multi-rate retry support, fix tx status reportingFelix Fietkau
Clean up the tx status reporting, fix retry counters (short retries are virtual collisions, not actual retries). Implement multi-rate retry support. This also fixes strong throughput fluctuations with rc80211_pid Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-06mac80211: free up 2 bytes in skb->cbFelix Fietkau
Free up 2 bytes in skb->cb to be used for multi-rate retry later. Move iv_len and icv_len initialization into key alloc. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-30ath5k: Add support for AR2417 v2Nick Kossifidis
* Add support for AR2417 (include pci id) since my previous patch doesn't sit on top of base.c/ath5k.h anymore. * Update module version to 0.6.0 Changes-Licensed-under: ISC Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-30ath5k: Fix SREV reporting after SREV updatesNick Kossifidis
* Fix srev reporting during attach Changes-Licensed-under: ISC Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-30ath5k: Update registers and SREV ids v2Nick Kossifidis
* Update registers * Update SREV values and add some PHY srevs * Prepare ath5k.h for newer radios etc Thanks to Atheros 's HAL source we now know for sure how many parts we have and what their SREV values are. We also have some updates on registers. Prepare ath5k for some major updates ;-) My previous mail had 2 more patches following (git log misusage), sorry for double posting ;-( Changes-Licensed-under: ISC Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-15mac80211: use nl80211 interface typesJohannes Berg
There's really no reason for mac80211 to be using its own interface type defines. Use the nl80211 types and simplify the configuration code a bit: there's no need to translate them any more now. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-05cfg80211: keep track of supported interface modesLuis R. Rodriguez
It is obviously good for userspace to know up front which interface modes a given piece of hardware might support (even if adding such an interface might fail later because of concurrency issues), so let's make cfg80211 aware of that. For good measure, disallow adding interfaces in all other modes so drivers don't forget to announce support for one mode when they add it. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-05ath5k: HW code cleanupNick Kossifidis
* No code changes... * Split hw.c to multiple files for better maintenance and add some documentation on each file code is going to grow soon (eeprom.c for example is going to get much stuff currently developed on ath_info) so it's better this way. * Rename following functions to maintain naming scheme: ah_setup_xtx_desc -> ah_setup_mrr_tx_desc (Because xtx doesn't say much, it's actually a multi-rate-retry tx descriptor) ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp (We don't put any "buf" we set descriptor pointers on hw) ath5k_hw_tx_start -> ath5k_hw_start_tx_dma ath5k_hw_start_rx -> ath5k_hw_start_rx_dma ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu (It's easier this way to identify them, we also have ath5k_hw_start_rx_pcu which completes the set) ath5k_hw_set_intr -> ath5k_hw_set_imr (As in get_isr we set imr here, not "intr") * Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can include support for different rx descriptors in the future * Further cleanups so that checkpatch doesn't complain (only some > 80 col warnings for eeprom.h and reg.h as usual due to comments) Tested on 5211 and 5213 cards and works ok. Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-29Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: net/mac80211/mlme.c
2008-08-26Ath5k: fix bintval setupJiri Slaby
bintval is set to the initial value at .config_interface which is too late, since it overwrites previously set value from .config. Move the initialization to the .add_interface. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-26Ath5k: lock beaconsJiri Slaby
Beacons setup and config was racy with beacon send. Ensure that ISR and reset functions see consistent state of bbuf. Use also dev_kfree_skb_any in ath5k_txbuf_free since we call it from atomic now. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22ath5k: set short preamble flag for rxBruno Randolf
set the short preamble flag in ieee80211_rx_status for frames received with a short preamble. drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22ath5k: explicitly check skb->lenHarvey Harrison
ieee80211_get_hdrlen_from_skb internally checks that the skb is long enough to hold the full header, or it returns 0 if not. The check in ath5k does not check this case and assumes it always got the actual header length which it then checks against the skb->len plus some headroom. Change to ieee80211_hdrlen which always returns the hdrlen and keep the existing headroom check. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22ath5k: rates cleanupBruno Randolf
cleanup the rates structures used by ath5k. instead of separate driver and mac80211 rate structures we now setup a static ieee80211_rate array and use it directly. no conversion between two different rate structures has to be done any more. a lot of unused and confusing junk was deleted. renamed ath5k_getchannels into ath5k_setup_bands because this is what it does. rewrote it to copy the bitrates correctly for each band. this is necessary for running different hardware with the same driver (e.g. 5211 and 5212 based cards). add special handling of rates for AR5211 chipsets: it uses different rate codes for CCK rates (which are actually like the other chips but with a 0xF mask). setup a hardware code to rate index reverse mapping table for getting the rate index of received frames. the rates for control frames which have to be set in ath5k_hw_write_rate_duration are now in one single array. drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD drivers/net/wireless/ath5k/base.h: Changes-licensed-under: 3-Clause-BSD drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22Ath5k: unify resetsJiri Slaby
There were 3 code copy and pastes of reset. Unify the resets and place in separate function. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22ath5k: add Mesh Point supportAndrey Yurovsky
This enables draft-802.11s Mesh Point operation. For that we need mesh beaconing. Tested with AR5212/AR5213 PCI card against Zydas and b43 mesh nodes. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-18removed unused #include <version.h>Huang Weiyi
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/net/wireless/ath5k/base.c drivers/net/wireless/b43/main.c drivers/net/wireless/ipw2100.c drivers/net/wireless/ipw2200.c drivers/net/wireless/iwlwifi/iwl-3945.c drivers/net/wireless/iwlwifi/iwl-4965.c drivers/net/wireless/iwlwifi/iwl-5000.c drivers/net/wireless/iwlwifi/iwl-agn.c drivers/net/wireless/iwlwifi/iwl-core.c drivers/net/wireless/iwlwifi/iwl-eeprom.c drivers/net/wireless/iwlwifi/iwl-hcmd.c drivers/net/wireless/iwlwifi/iwl-power.c drivers/net/wireless/iwlwifi/iwl3945-base.c This patch removes the said #include <version.h>. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-10 16:36:31 +0000