aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/rtl818x.h
AgeCommit message (Collapse)Author
2008-08-22rtl818x: merge tx/rx descriptor flagsHerton Ronaldo Krzesinski
Tx/Rx descriptor flags are common between rtl818x devices, only with additions for newer chips, thus use same flags in the code. Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-07-08rtl8187: Change detection of RTL8187B with USB ID of 8187Larry Finger
Some early versions of RTL8187B devices have a USB ID of 0x8187 rather than the 0x8189 of later models. In addition, it appears that these early units also must be programmed with lower power. Previous patches used the Product ID string to detect this situation, but did not address the low power question. This patch uses the hardware version and sets the power accordingly. Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-07-08rtl8187: updating rtl818x.h to support RTL8187BHin-Tak Leung
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29cfg80211 API for channels/bitrates, mac80211 and driver conversionJohannes Berg
This patch creates new cfg80211 wiphy API for channel and bitrate registration and converts mac80211 and drivers to the new API. The old mac80211 API is completely ripped out. All drivers (except ath5k) are updated to the new API, in many cases I expect that optimisations can be done. Along with the regulatory code I've also ripped out the IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be unnecessary if the hardware simply gives us whatever channels it wants to support and we then enable/disable them as required, which is pretty much required for travelling. Additionally, the patch adds proper "basic" rate handling for STA mode interface, AP mode interface will have to have new API added to allow userspace to set the basic rate set, currently it'll be empty... However, the basic rate handling will need to be moved to the BSS conf stuff. I do expect there to be bugs in this, especially wrt. transmit power handling where I'm basically clueless about how it should work. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28Add rtl8180 wireless driverMichael Wu
This patch adds a mac80211 based wireless driver for the rtl8180 and rtl8185 PCI wireless cards. Also included are some rtl8187 changes required due to the relationship between that driver and this one. Michael Wu is primarily responsible for the initial driver and rtl8185 support. Andreas Merello provided the additional rtl8180 support. Thanks to Jukka Ruohonen for the donating a rtl8185 card! It was very helpful for the rtl8225z2 code. The Signed-off-by information below is collected from the individual patches submitted to wireless-2.6 before merging this driver upstream. Signed-off-by: Andrea Merello <andreamrl@tiscali.it> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] mac80211: revamp interface and filter configurationJohannes Berg
Drivers are currently supposed to keep track of monitor interfaces if they allow so-called "hard" monitor, and they are also supposed to keep track of multicast etc. This patch changes that, replaces the set_multicast_list() callback with a new configure_filter() callback that takes filter flags (FIF_*) instead of interface flags (IFF_*). For a driver, this means it should open the filter as much as necessary to get all frames requested by the filter flags. Accordingly, the filter flags are named "positively", e.g. FIF_ALLMULTI. Multicast filtering is a bit special in that drivers that have no multicast address filters need to allow multicast frames through when either the FIF_ALLMULTI flag is set or when the mc_count value is positive. At the same time, drivers are no longer notified about monitor interfaces at all, this means they now need to implement the start() and stop() callbacks and the new change_filter_flags() callback. Also, the start()/stop() ordering changed, start() is now called *before* any add_interface() as it really should be, and stop() after any remove_interface(). The patch also changes the behaviour of setting the bssid to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed and the filter flag FIF_BCN_PRBRESP_PROMISC introduced. This is a lot more efficient for hardware like b43 that supports it and other hardware can still set the BSSID to all-ones. Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu (rtl8187, adm8211, and p54), Larry Finger (b43legacy), and Ivo van Doorn (rt2x00). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-07-08[PATCH] rtl8187: add header blocks and indicate origin of magic valuesJohn W. Linville
Add top-of-file comment blocks to rtl818x headers and attribute origin of magic values to original r8187 driver. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-07-08[PATCH] Add rtl8187 wireless driverMichael Wu
This patch adds a mac80211 based wireless driver for the rtl8187 USB wireless card. Signed-off-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>