| Age | Commit message (Collapse) | Author |
|---|
|
The Coverity checker noted that these "if (err)"'s couldn't ever be
true.
It seems the intention was to check the return values of the
bcm43xx_pci_write_config32()'s?
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Drain the Microcode TX-status-FIFO before we enable IRQs.
This is required, because the FIFO may still have entries left
from a previous run. Those would immediately fire after enabling
IRQs and would lead to an oops in the DMA TXstatus handling code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The bcm43xx driver uses 4 locations in the devices sprom to determine
the behavior of the leds. Certain defaults are assigned if all bits are
set in those locations. On at least one BCM4303 chip, the sprom contains
values other than the default, which executes an assertion placed in the
default case of a following switch statement. This patch makes the leds
on the above mentioned interface behave correctly. In addition, it limits
the number of logged messages to 20 for the case of unexpected values in
the sprom locations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes a netdev watchdog timeout problem.
The software needs to call netif_tx_disable before running the
hardware calibration code. The problem condition can be shown by the
following timegraph.
|---5secs - ~10 jiffies time---|---|OOPS
^ ^
last real TX periodic work stops netif
At OOPS, the following happens:
The watchdog timer triggers, because the timeout of 5secs
is over. The watchdog first checks for stopped TX.
_Usually_ TX is only stopped from the TX handler to indicate
a full TX queue. But this is different. We need to stop TX here,
regardless of the TX queue state. So the watchdog recognizes
the stopped device and assumes it is stopped due to full
TX queues (Which is a _wrong_ assumption in this case). It then
tests how far the last TX has been in the past. If it's more than
5secs (which is the case for low or no traffic), it will fire
a TX timeout.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The length of the manfid CIS should be at least 4, and it's normally 4.
It's incorrect to require it to be at least 5. This breaks support for
most (if not all) cards.
The right place to ensure that we don't access beyond the CIS buffer is
to strengthen another check. Make sure that the next tuple begins at
least at the CIS buffer end (in which case we stop processing) or
before that.
Reported by ph35sm@free.fr
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As a replacement for the broad manufactor/card ID match we commented out
because of conflicts with pcnet_cs, add two product ID matches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The break was caused by 7c28ad2d83ecc637237fe684659a6afbce0bb2a8.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The airo driver used to break out of while loop if there were any signals
pending. Since it no longer checks for signals, it at least needs to check
if it needs to be frozen.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After the Orinoco issue, I did an audit of other drivers for the same
issue. Three drivers were NULL terminating the ESSID, which could cause an
overflow in WE-21 when the ESSID has maximum size.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If we enter the if(!zd) and set free to 1, we dereference zd in the exit
code.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes the Orinoco driver overflow issue with
WE-21.
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
create_proc_entry() can fail and return NULL in setup_proc_entry(), the
result must be checked before dereferencing. (Coverity ID 1443)
init_wifidev() & setup_proc_entry() can also fail in _init_airo_card().
This adds the checks & cleanup code and removes some whitespace.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The bcm43xx-softmac software currently fails when running on x86_64 systems
with more than 1GB RAM and one of the card variants with 30-bit DMA addressing.
This patch uses the address extension bits in the hardware to set the correct
DMA mask for the specific card in use.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Linus's tree now has a configuration option that prints a warning whenever
the returned value of any routine is ignored. This patch fixes the only such
warning for bcm43xx.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes some race conditions in the WirelessExtension
handling and association handling code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is a potential race condition in the periodic_work_handler routine
of bcm43xx-softmac. In addition to fixing this condition, the size of code is
reduced by moving the mutex lock outside the if.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
- Eliminate check for irq handler 'dev_id==NULL' where the
condition never occurs.
- Eliminate needless casts to/from void*
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (37 commits)
[netdrvr] hp100: encapsulate all non-module code
drivers/net/wireless/{airo,ipw2100}: fix error handling bugs
[netdrvr] phy: Fix bugs in error handling
[PATCH] spidernet: Use pci_dma_mapping_error()
[PATCH] sky2: version 1.9
[PATCH] sky2: fragmented receive for large MTU
[PATCH] sky2: use netif_tx_lock instead of LLTX
[PATCH] sky2: incremental transmit completion
[PATCH] sky2: name irq after eth for irqbalance
[PATCH] sky2: workarounds for some 88e806x chips
[PATCH] sky2: use standard pci register capabilties for error register
[PATCH] sky2: gigabit full duplex negotiation
e100, e1000, ixgb: increment version numbers
ixgb: convert to netdev_priv(netdev)
ixgb: combine more rx descriptors to improve performance
e1000: possible memory leak in e1000_set_ringparam
e1000: Janitor: Use #defined values for literals
e1000: don't strip vlan ID if 8021q claims it
e1000: rework polarity, NVM, eeprom code and fixes.
e1000: driver state fixes (race fix)
...
|
|
The last in-kernel user of errno is gone, so we should remove the definition
and everything referring to it. This also removes the now-unused lib/execve.c
file that was introduced earlier.
Also remove every trace of __KERNEL_SYSCALLS__ that still remained in the
kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
airo:
* fix oops, if !CONFIG_PROC_FS (create_proc_entry always returns NULL)
* handle pci_register_driver() failure. if it fails, we really do
want to exit, rather than (as a comment indicates) return success
because-we-are-a-library.
* #if 0 have_isa_dev variable, which is assigned a value but never used
ipw2100:
* handle sysfs_create_group() failure
* handle driver_create_file() failure
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add infrastructure to track "maximum allowable latency" for power saving
policies.
The reason for adding this infrastructure is that power management in the
idle loop needs to make a tradeoff between latency and power savings
(deeper power save modes have a longer latency to running code again). The
code that today makes this tradeoff just does a rather simple algorithm;
however this is not good enough: There are devices and use cases where a
lower latency is required than that the higher power saving states provide.
An example would be audio playback, but another example is the ipw2100
wireless driver that right now has a very direct and ugly acpi hook to
disable some higher power states randomly when it gets certain types of
error.
The proposed solution is to have an interface where drivers can
* announce the maximum latency (in microseconds) that they can deal with
* modify this latency
* give up their constraint
and a function where the code that decides on power saving strategy can
query the current global desired maximum.
This patch has a user of each side: on the consumer side, ACPI is patched
to use this, on the producer side the ipw2100 driver is patched.
A generic maximum latency is also registered of 2 timer ticks (more and you
lose accurate time tracking after all).
While the existing users of the patch are x86 specific, the infrastructure
is not. I'd like to ask the arch maintainers of other architectures if the
infrastructure is generic enough for their use (assuming the architecture
has such a tradeoff as concept at all), and the sound/multimedia driver
owners to look at the driver facing API to see if this is something they
can use.
[akpm@osdl.org: cleanups]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian. Annotated them and variables that are inferred to be
net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
[PATCH] bonding: update version number
[PATCH] git-netdev-all: pc300_tty build fix
[PATCH] Make PC300 WAN driver compile again
[PATCH] Modularize generic HDLC
[PATCH] more s2io __iomem annotations
[PATCH] restore __iomem annotations in e1000
[PATCH] 64bit bugs in s2io
[PATCH] bonding: Fix primary selection error at enslavement time
[PATCH] bonding: Don't mangle LACPDUs
[PATCH] bonding: Validate probe replies in ARP monitor
[PATCH] bonding: Don't release slaves when master is admin down
[PATCH] bonding: Add priv_flag to avoid event mishandling
[PATCH] bonding: Handle large hard_header_len
[PATCH] bonding: Remove unneeded NULL test
[PATCH] bonding: Format fix in seq_printf call
[PATCH] bonding: Convert delay value from s16 to int
[PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Delete unused drivers/net/gt64240eth.h
[PATCH] skge: fiber support
[PATCH] fix possible NULL ptr deref in forcedeth
...
|
|
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The setup for running long periodic work has a bug that leads to
netdev watchdog tx timeouts. This change eliminates the timeouts.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch includes a big cleanup of the existing unused LED code,
and adds support for controlling the LED.
The link LED will blink if the device is not associated. The LED
switches between 2 seconds on and 1 second off. If the device is
associated the LED is switched on.
The link LED also indicates packet TX. I do a little bit more led
resetting than the vendor driver, but the device works now as
expected for single LED and double LED devices.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For housekeeping and watchdog tasks a workqueue is created. The
central workqueue is not used to prevent crashes creates by bugs.
It might be changed, when the housekeeping is stabilized.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Checking whether a mutex is not locked directly before
mutex_lock() is called, doesn't make sense. The whole point of
mutex_lock() is to block, if the mutex is locked.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Caused by the fact that physical control registers appear to have
only a width of 16 bit, 32-bit writes are not required.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
An error message is changed to a printk as the original dprintk
would be optimized away if debugging were not enabled. If the error
is triggered, a more meaningful message is returned.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In bcm43xx-softmac, the bcm43xx_stats struct contains a variable that
is no longer used. In addition, two TODO entries related to noise
processing in bcm43xx_rx have been completed, and as unused one
is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch updates the PHY initialization code for bcm43xx-softmac
to conform with recent changes in the clean-room specs at
http://bcm-specs.sipsolutions.net. Mostly, these changes implement
the sequence needed for chips with GPHY revision 8; however, the
patch also corrects a typo in one address, and some parts that were
missing from the spec when the initial coding was done.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch to make bcm43xx-softmac be compatible with the revised SSID
length of WE-21.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
net/ieee80211/ieee80211_crypt_tkip.c
net/ieee80211/ieee80211_crypt_wep.c
|
|
This patch converts all remaining users to use the new block cipher type
where applicable. It also changes all simple cipher operations to use
the new encrypt_one/decrypt_one interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
