| Age | Commit message (Collapse) | Author |
|---|
|
OLC_FOR_AR9280_20_LATER is defined in multiple places,
move it to a common location.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Reset automatically the TSF on re-enabling beaconing after scanning
in IBSS mode causes several problems. For example a new created IBSS
network can't age before an other node has joined, because scans are
done automatically in that case. And several other strange bugs more...
The TSF reset is done manually in the higher level mac80211 code in
the cases were it's needed, so we don't need to do it here.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In the old days we used one slot per frame. But when we changed that to 2,
we didn't raise the overall slot count. Which resulted in an effective
division of two to the number of slots.
Double the number of TX slots, so we have an effective hardware queue
of 128 frames per QoS queue.
Also optimize the TX header cache handling. We don't need a cached TX header
for slots that will never carry an actual header.
So we reduce the memory consumption of the cache by 50%.
So as a net result we end up with more or less the same memory usage before
and after this patch (except a few tiny meta structures), but have twice
the number of TX slots available.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes hidden bugs in the size handling of the DMA buffers.
This sets the RX buffer size to the theoretical max packet size and
fixes passing of the size values to the device (must not subtract the header offset).
These bugs are hidden and don't actually trigger due to the magic +100
offset for the buffer size.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move the DMA stop sanity check up a few lines, so it's actually
theoretically possible to trigger. (But it still shouldn't trigger, of course).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Passing beacons received from other BSS to s/w in non-scanning
state is unnecessary in STA mode. This patch filters them out in
h/w.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When iwlwifi runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's. This is because iwlwifi
driver calls DMA mapping with PCI_DMA_TODEVICE which is read only in mapping
PTE. But iwlwifi device actually writes to the mapped page to update its contents.
This issue is not exposed in swiotlb. But VT-d hardware can capture this fault and
stop the fault transaction.
The iwl TX command contains a scratch field that is updated by uCode to
indicate retry counts. For 5000 series the patch is required also for
regular frames, but this patch does not differenciate.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch unifies use of SW rfkill between 3945 and agn driver.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
iwl3945 uses iwl_isr and deletes duplicated iwl3945_isr.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch removes duplicate code to enable and disable interrupt.
iwl3945 now uses iwlwifi's functions.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch removes duplicate code from iwl3945 and uses
iwl_rx_reply_error and spectrum notifications from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch removes duplicate rx handlers(pm_sleep and pm_debug) from 3945 and
uses handlers from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
3945 can use iwl_mac_hw_scan callback instead of
iwl3945_mac_hw_scan callback.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch makes use of iwl_rx_scan handler for 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
at76_debug should be an unsigned int as it used as a bit field. In
fact, modprobe fails when trying to set at76_debug's high bit.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With the latest mac80211 stack, the driver needs to be updated for
cfg80211 scanning. I based the changes off of modifications for
at76_usb found here:
http://johannes.sipsolutions.net/patches/old/all/2008-09-19-13:35/020-cfg80211-scan.patch
The trick was that max_signal also needs to be set to avoid a divide
by zero Oops. I just guessed and used the value 100 for now.
kvalo: handpicked the change from two different patches
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is a driver for usb devices based on at76c50x chipset. This is
a mac80211 port of the original at76_usb driver.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Default to MAX_UCODE_BEACON_INTERVAL if the output of
iwl_adjust_beacon_interval would otherwise be zero. This prevents a
division by zero on my iwl5300-equipped Lenovo T400 with kernels that
include "mac80211: use cfg80211s BSS infrastructure".
This patch is a bit of a hack -- I'm not sure why iwl_setup_rxon_timing
is giving iwl_adjust_beacon_interval a zero input (which is the only way
it would output zero). I would be happy to have a better fix. But for
now, this makes my box boot...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch expands the parenthesis in the txctl reg write
of the LO calibration to enforce precedence rules.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Only FIF_FCSFAIL is set due to parentheses
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Scanned BSS entries are timestamped with jiffies, which doesn't
increment across suspend and hibernate. On resume, every BSS in the
scan list looks like it was scanned within the last 10 seconds,
irregardless of how long the machine was actually asleep. Age scan
results on resume with the time spent during sleep so userspace has a
clue how old they really are.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some APs don't start BA negotiation with the client before it is done
with the key handshake in WPA/RSN. With those APs, key handshake times
out if EAPOL frames are sent after addba request. So defer the BA negotiation
until we are done with tx/rx of all EAPOL frames.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The word_base is in bytes instead of word index number,
this means that when using it, it should be transformed into
a word index first.
Otherwise RF register reading will fail through debugfs since
we would start reading 4 words starting with word 4 (which is the last
valid word for RF).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Setting up the CAB queue requires only the beacon interval,
remove the function ath_get_beaconconfig() which is redundant.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Set channel change time to 5ms, this will improve scan results.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
RX and calibration have different timeout requirements.
This patch fixes it by changing the HW wait routine
to accept a timeout value.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch programs the RTC registers of AR9100 chipsets
correctly during chip reset.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
RTS and CTS-to-self duration needs to go after ICV len is considered.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We currently send beacons directly from the interrupt routine. This
can hold up interrupt processing in beaconing modes and makes the
ISR somewhat more complex. Move it to a tasklet like rx and tx.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath5k_reset can be called from process context, which in turn can
call ath5k_beacon_config which takes the sc->block spinlock. Since
it can also be taken in hard irq context, use spin_lock_irqsave
everywhere. This fixes a potential deadlock in adhoc mode.
Changes-licensed-under: 3-Clause-BSD
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since interrupts are already masked by the hardware, there's no need to
discard interrupt bits in the ISR itself. Also, in ath5k_beacon_config
we mask off a couple of bits without locking, so doing this mask in
software can lead to unhandled beacon timer and beacon miss interrupts.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The only way rf_write() can be called with word 0 is
when the user sends the wrong word index through debugfs.
However the values which are send through debugfs are
validated using the RF_BASE and RF_SIZE macro values,
the most logical solution is to increase RF_BASE with 4
and decrease RF_SIZE with 4 (RF_SIZE has always been
1 word too big)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The atomic requirement for get_tsf() has been removed
by mac80211. This means the USB drivers can add support
for the callback function again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fixes:
- iwlwifi is an optional driver and should thus not default to 'y'.
- 3945 now depends on IWLCORE.
Rework:
- There is not a case when IWLCORE should not be selected. At the same time
the driver does not use IWLWIFI or IWLCORE. We can just merge the usage of
these two. With IWLWIFI being the driver name we proceed to use just it and
replace instances of IWLCORE with it. The module name does not change
and is still iwlcore.
- Both IWLAGN and IWL3945 are selecting FW_LOADER, we can thus just move
this up to one select when IWLWIFI is selected.
- IWL5000 now supports Intel Wireless Wifi 100, 6000, and 6050 series.
- Now that 3945 depends on IWLWIFI we can also indicate its dependency on
MAC80211_LEDS and LEDS_CLASS at this level.
- IWLAGN_LEDS is not used by driver - remove it.
- IWLAGN_SPECTRUM_MEASUREMENT actually depends on IWLWIFI as it forms part
of iwlcore module. Move this config up in Kconfig to reflect that and also
change name to IWLWIFI_SPECTRUM_MEASUREMENT.
- CONFIG_IWLWIFI_RFKILL is used by iwlagn as well as iwl3945, add text to
description that indicates this.
- CONFIG_IWL3945_RFKILL does not exist - remove usage from driver.
- Add "iwlagn" to end of description of IWLAGN to help people understand
what iwlagn means in rest of Kconfig text.
- Add "iwl3945" to end of description of IWL3945 to help people understand
what iwlagn means in rest of Kconfig text.
- Change IWLWIFI_DEBUGFS description to indicate that only iwlagn supports
it (for now).
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use one workqueue instead of one per CPU.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
- some of them are defined as follows:
#define ipw_write32 expr1; expr2
and are called from loops or ifs without a compound statement, so
they are broken. Fix it by putting them into do {} while (0) for
writes and ({ }) for reads.
- also unify and cleanup them while at it -- convert them from
macros to inline functions, so that we get some basic typechecking
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Both branches of the regulatory check in ath_attach() set up a
custom regulatory domain and apply radar and world flags, so extract
those into a single path.
While at it, fix a couple of spelling errors and an unnecessary extra
pointer traversal.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_regd_get_current_country() doesn't exist.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The function ath9k_regd_get_rd() is unused.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Write isWwrSKU as an inline function and nix the camel-case to make
the routine slightly clearer. Change its argument to take the regd
value directly so it can eventually be used by ath5k as well.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since we already have a stack variable to track the eeprom regd,
we can grab it up front it and save three calls to fetch it again.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The current_rd_inuse regulatory value is assigned but not used anywhere.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This avoids triggering a BUG_ON in pci_disable_msi in the error path.
Furthermore remove the first call to pci_disable_device as it is already
called at out_pci_disable_device.
Both issues were introduced in the patch "iwlagn: fix hw-rfkill while
the interface is down".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds Open Loop Control support for Atheros chipsets that
supports open loop power control.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
