| Age | Commit message (Collapse) | Author |
|---|
|
When network interface is made active we were not handling the error
scenarios properly to clean up rx & tx resources which might result in
a driver panic.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch resolves an issue with map single being used to map a buffer and
then unmap page being used to unmap it. In addition it handles any error
conditions that may be detected using skb_dma_map.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MSI-X allocation broke after the 82599 merge on systems with more than 8
CPU cores. 82598 drops back into MSI mode, which isn't sufficient to run
full, efficient 10G line rate.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the past flow control wasn't enabled by default under the
incorrect assumption that this opened up us to a denial of
service attack. However since any switch that forwarded flow
control would be extremely msiconfigured and/or buggy, this
concern no longer out weighs the preformance gains from
having FC enabled.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The priority flow control settings from the netlink layer aren't taking
effect in the base driver. The boolean pfc_mode_enable in the dcb_config
struct isn't being set, so the hardware configuration code is never
reached.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethtool tries to get advertised speed from phy.autoneg_advertised.
However for copper media this wasn't happening until later do to
an other fix which moved mac.ops.setup_link_speed placement in
ixgbe_link_config(). This patch will display the default advertised
speeds if it can't yet get this information from phy.autoneg_advertised.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete. This patch completes the code based off of the code that
already existed in the igb module.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Impact: Fix
Yinghai Lu found one system with 82575EB where, in the kernel that is
kexeced, probe igb failed with -2, the reason being that the adapter
could not be brought back from D3 by the kexec kernel, most probably
due to quirky hardware (it looks like the same behavior happened on
forcedeth).
Prevent igb from putting the adapter into D3 during shutdown except
when we going to power off the system. For this purpose, seperate
igb_shutdown() from igb_suspend() and use the appropriate PCI PM
callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code path for setting up phy loopback testing was out of date and was
setting bits it didn't need to. This change cleans up the code path and
removes some code that has no effect on teh driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase the delay for copper phy init from 15ms to 100ms. This is to
address issues seen in which ethtool -t was failing in some cases on 82576
based adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An issue was seen on suspend in which the system reported a page fault. This
was due to the new reg_idx code being called after the queues were freed.
This update prevents any for loops from going through the queues by setting
the number of queues to 0 when they are freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When device is on PCIe link trained as x2 the driver is currently reporting
link width as "unknown". The original patch provided by Myron adds the x2
link support and my changes are cosmetic to clean up the readability of the
conditional operators.
Based on work by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FEC Ethernet device isn't always attached to a phy. Be careful
not to dereference phy_device if it is NULL. Also eliminates an
unnecessary extra function from the ioctl path.
Reported-by: Henk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since not using net_device_ops gets you shunned out the cool crowd,
this patch modifies the fec_mpc52xx Ethernet driver to provide the
management hooks via a struct net_device_ops.
Reported-by: Henk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver triggers a BUG_ON() when allocating DMA buffers because the
arch/powerpc dma_ops aren't in the net_device's struct device. This
patch fixes the problem by using the parent of_device which does have
the correct dma_ops set.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Kconfig and Makefile related changes for vxge driver.
- No changes in current submission.
- Changes from previous submission -
- Incorporated the following review comments as per Bill Flink:
- Add dependancy on INET along with PCI
- Remove dependancy on INET_LRO and add GRO support.
- Made this patch as last patch as per Ben Hutchings comments.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Driver version
- Changes from previous submission -
- Updated driver version.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements all ethtool related entry point functions for the driver.
- Changes in this submission -
- Removed redundant #include statements
- Changes in previous submissions -
- Removed unused statistics.
- General clean up - removed unused variables and macros.
- Incorporated following comments from Ben Hutchings
- No need to restart the interface in vxge_ethtool_sset
- Do not use #ifdef ADVERTISED_XX
- Remove unnecessart intermediate copy in vxge_ethtool_gdrvinfo
- Use strlcpy() to ensure null-termination.
- Use ethtool_op_get_tso, ethtool_op_set_tx_hw_csum instead
of redefining the same code.
- Implement get_strings_count instead of deprecated get_stats_count.
- Don't report reporting the EEPROM length as we don't supprt
get/set eeprom.
- Don't set self_test_count as we don't support any self tests.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements all the driver entry point functions.
- Definition of all module loadable paramters.
- Implementation of all driver entry point functions.
- Changes in this submission -
- Fixed compilation error when enabling debug statements
- Fixed few warnings when CONFIG_PCI_MSI is not defined
- Removed unnecessary volatile variables
- Removed compare_ether_addr as it causes unaligned memory access on
the sparc64 platform.
- Changes in previous submissions -
- As per Stephen Hemminger's comments removed the following loadable
parameters - gro, rx_& tx max_indicate_pkts, exec_mode, rx & tx
pause_enable, tx_steering_type and intr_type.
- Added Device ID definition in vxge-main.h instead of
include/linux/pci_ids.h file - Reported by David Miller
- Incorporated following review comments from Ben Hutchings
- NAPI is always enabled (no option to turn it OFF).
- Loadable parameters
rx_steering_type: This loadable option is removed.
ring_blocks: This loadable option is removed.
The driver default settings work well in most if not all cases.
Another patch to configure these parameters with ethtool will be
released in the future.
- LRO has been deprecated in favour of GRO - Bill Fink & Dave Miller's comment
- Fixed sparse warnings - Reported by Andi Kleen
- Removed unused variables
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch takes care of trafic handling related APIS.
- Interrupt Enable and disable
- Mask / Unmask Interrupt
- Traffic Interrupt handling.
- Alarm Interrupt handling.
- Changes in this submission -
- General clean up - removed redundant includes, defines and macros.
- Changes in previous submissions -
- General cleanup - removed unused functions and variables.
- Use asserts where necessary - Reported by Andi Kleen
- Fixed sparse warnings - Reported by Andi Kleen
- Use a prefix, "__vxge" in front of hw functions to make them globally
unique - Ben Hutchings
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch takes care of Initialization and configuration steps of
Neterion Inc's X3100 Series 10GbE PCIe I/O Virtualized Server Adapter.
- Device Initialization.
- Verification and setting of device config parameters.
- Allocation of Tx FIFO and Rx Ring descriptors (DTR).
- APIs to get various type of hw stats
- APIs to configure RTS (Receive Traffic Steering)
- Changes in this submission -
- Include vmalloc header without which a compilation error occured
on sparc64, ppc64 and IA64 plaforms.
- Fixed compilation warning in register_poll, write32_upper,
write32_lower and the special write64 functions on ppc64.
- General cleanup - removed redundant includes and defines.
- Changes in previous submissions -
- Add readq/writeq implementation for the driver for 32 bit systems -
reported by Dave Miller.
- Incorporated following comments from Ben Hutchings
- Start a comment with "/**" to make it a kernel-doc comment.
- Use prefix, "__vxge" in front of hw functions to make them globally
unique.
- Fixed unnecessary clearing members of *channel just before freeing
- Use backslashes only for macro definitions and not in multi-line
statements.
- Used pci_find_capability instead of redefining it.
- Used device and revision ids that are already in pdev - no need to
read them again.
- Used pci_save_state() and pci_restore_state() around resets.
- Used udelay and mdelay directly instead of wrapper.
- In __vxge_hw_device_register_poll() reset i to 0 after the
microsecond delay loop to commence the millisecond delay loop.
- Corrected spelling "sapper" - should be "swapper"
- Remove too much vertical whitespace.
- Replaced magic numbers with appropriate macros
- Incorporated following comments from Andi Kleen [andi@firstfloor.org]
- Reduced the arguments in functions or refactored them into smaller
functions.
- Allocate page sized memories used in slow path with vmalloc.
- Use asserts where necessary.
- Use macros instead of magic numbers.
- Use the pci layer code instead of defining own functions
- Remove driver wrappers such as xge_hw_device_private_set().
- Fixed sparse warnings.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Complete Register map details of Neterion Inc's X3100 Series 10GbE PCIe I/O
Virtualized Server Adapter.
- No change from previous submission.
- Changes in previous submissions -
- Incorporated following comments from Ben Hutchings
- Use original macros for endian checks
- Remove VXGE_OS_PLATFORM_* macros as they are unused.
- Converted multiple bVALX macros into single with additional
width parameter and renamed it to vxge_bVALn.
- Using __packed instead of pragma pack(1)
- Added a comment of the use of a hw swapper so driver code is
portable (does not have to change the byte order for register
access as well as dma operations) on different ENDIAN platforms.
- Using the <linux/pci_regs.h> definitions instead of redefing them.
- Using the PCI capabilities registers in <linux/pci_regs.h>
instead of redefing them.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we use a shared legacy IRQ then our interrupt handler may be called
as soon as it is registered even though IRQs are disabled on the NIC.
Now that the legacy interrupt handler also checks for event delivery,
it may decide to schedule polling in this case. Ensure that the NAPI
context is valid but disabled at this point.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/net-next-2.6
|
|
Let driver depend on HAS_IOMEM to avoid build breakage on s390:
CC drivers/net/ethoc.o
drivers/net/ethoc.c: In function 'ethoc_read':
drivers/net/ethoc.c:221: error: implicit declaration of function 'ioread32'
drivers/net/ethoc.c: In function 'ethoc_write':
drivers/net/ethoc.c:226: error: implicit declaration of function 'iowrite32'
drivers/net/ethoc.c: In function 'ethoc_rx':
drivers/net/ethoc.c:405: error: implicit declaration of function 'memcpy_fromio'
drivers/net/ethoc.c: In function 'ethoc_start_xmit':
drivers/net/ethoc.c:828: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added osi_load_firmware() instead of copying same thing twice
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
Added predef variable in add_mcs() to support predefined mcs data
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.
Also fix error return values.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allows for the removal of byteswapping in some places and
the removal of HIPQUAD (replaced by %pI4).
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/hamradio/dmascc.c:587: error: 'struct net_device' has no
member named 'set_mac_address'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'percpu-cpumask-x86-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (682 commits)
percpu: fix spurious alignment WARN in legacy SMP percpu allocator
percpu: generalize embedding first chunk setup helper
percpu: more flexibility for @dyn_size of pcpu_setup_first_chunk()
percpu: make x86 addr <-> pcpu ptr conversion macros generic
linker script: define __per_cpu_load on all SMP capable archs
x86: UV: remove uv_flush_tlb_others() WARN_ON
percpu: finer grained locking to break deadlock and allow atomic free
percpu: move fully free chunk reclamation into a work
percpu: move chunk area map extension out of area allocation
percpu: replace pcpu_realloc() with pcpu_mem_alloc() and pcpu_mem_free()
x86, percpu: setup reserved percpu area for x86_64
percpu, module: implement reserved allocation and use it for module percpu variables
percpu: add an indirection ptr for chunk page map access
x86: make embedding percpu allocator return excessive free space
percpu: use negative for auto for pcpu_setup_first_chunk() arguments
percpu: improve first chunk initial area map handling
percpu: cosmetic renames in pcpu_setup_first_chunk()
percpu: clean up percpu constants
x86: un-__init fill_pud/pmd/pte
x86: remove vestigial fix_ioremap prototypes
...
Manually merge conflicts in arch/ia64/kernel/irq_ia64.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (119 commits)
[SCSI] scsi_dh_rdac: Retry for NOT_READY check condition
[SCSI] mpt2sas: make global symbols unique
[SCSI] sd: Make revalidate less chatty
[SCSI] sd: Try READ CAPACITY 16 first for SBC-2 devices
[SCSI] sd: Refactor sd_read_capacity()
[SCSI] mpt2sas v00.100.11.15
[SCSI] mpt2sas: add MPT2SAS_MINOR(221) to miscdevice.h
[SCSI] ch: Add scsi type modalias
[SCSI] 3w-9xxx: add power management support
[SCSI] bsg: add linux/types.h include to bsg.h
[SCSI] cxgb3i: fix function descriptions
[SCSI] libiscsi: fix possbile null ptr session command cleanup
[SCSI] iscsi class: remove host no argument from session creation callout
[SCSI] libiscsi: pass session failure a session struct
[SCSI] iscsi lib: remove qdepth param from iscsi host allocation
[SCSI] iscsi lib: have lib create work queue for transmitting IO
[SCSI] iscsi class: fix lock dep warning on logout
[SCSI] libiscsi: don't cap queue depth in iscsi modules
[SCSI] iscsi_tcp: replace scsi_debug/tcp_debug logging with iscsi conn logging
[SCSI] libiscsi_tcp: replace tcp_debug/scsi_debug logging with session/conn logging
...
|
|
Conflicts:
sound/soc/pxa/pxa2xx-i2s.c
|
|
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When TX aggregation becomes operational, we do a number of steps:
1) print a debug message
2) wake the virtual queue
3) notify the driver
Unfortunately, 1) and 3) are only done if the driver is first to
reply to the aggregation request, it is, however, possible that the
remote station replies before the driver! Thus, unify the code for
this and call the new function ieee80211_agg_tx_operational in both
places where TX aggregation can become operational.
Additionally, rename the driver notification from
IEEE80211_AMPDU_TX_RESUME to IEEE80211_AMPDU_TX_OPERATIONAL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
change the display of current driver status bit to user readable format
for better and easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We shouldn't return NETDEV_TX_BUSY from the TX callback, especially
after we've mucked with the sk_buffs. Drop the packets and return
NETDEV_TX_OK.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch restores all-in-one module build procedure for ar9170.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We were claiming DMA buffers on the RX tasklet but never
upon a simple module removal.
Cc: stable@kernel.org
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath5k sets up a mapping table from the hardware rate index to
the rate index used by mac80211; however, we have seen some
received frames with incorrect rate indexes. Such frames
normally get dropped with a warning in __ieee80211_rx(),
but it doesn't include enough information to track down the
error.
This patch adds a warning to hw_to_driver_rix for any lookups
that result in a rate index of -1, then returns a valid rate so
the frame can be processed.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
