| Age | Commit message (Collapse) | Author |
|---|
|
The new e1000e driver is apparently not yet suitable for general use, so
mark it experimental, and re-instate all the PCI-Express device IDs in
the old and stable e1000 driver so that people (namely me) can continue
to use a driver that actually works.
Auke & co have been appraised of the situation.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a bunch of warnings in PPP and related drivers. Mostly because
sparse doesn't like it when the the function is only marked private in
the forward declaration.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Needed to propagate it down to the ip_route_output_flow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
always extend the rx timestamp with the local TSF, since this information is
also needed for proper IBSS merging. this is done in the tasklet for now, maybe
has to be moved to the interrupt handler like in madwifi.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
in "11.1.2.2 Beacon generation in an IBSS" the IEEE802.11 standard says, each
STA should... "b) Calculate a random delay uniformly distributed in the range
between zero and twice aCWmin × aSlotTime,".
configure cwmin and cwmax of the beacon queue in IBSS mode according to this.
unfortunately beacon backoff does not work reliably yet, so i suspect we have a
problem somewhere else, since the same settings (and similar beacon timer
configuration) work for madwifi.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
use SWBA (software beacon alert) interrupts to keep track of the next beacon
time und check if a HW merge (automatic TSF update) has happened on every
received beacon with the same BSSID.
this is necessary because the atheros hardware will silently update the local
TSF in IBSS mode, but not its beacon timers. if the TSF is ahead of the beacon
timers no beacons are sent until the timers wrap around (typically after about
1 minute).
this solution is not very nice, since we have to look into every beacon, but
there is apparently no other way to detect HW merges.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
update ath5k_beacon_update_timers() for better beacon timer calculation in a
variety of situations. most important is the possibility to call it with the
timestamp of a received beacon, when we detected that a HW merge has happened
and we need to reconfigure the beacon timers based on that.
we call this from the mac80211 callback reset_tsf now instead of beacon_update,
and there will be more use of it in the next patch.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
the beacon interval is passed by mac80211 in TU already, so we can directly use
it without conversion. also update the comments about TU (1 TU is defined by
802.11 as 1024usec).
drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
reviewed beacon timer initialization with register traces from madwifi: what we
are doing is correct :). one minor fix: use 3 instead of 0x00000003 - it's more
readable.
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This zeros out all microcode related memory before loading
the microcode.
This also fixes initialization of the MAC control register.
The _only_ place where we overwrite the contents of the MAC control
register is at the beginning of b43_chip_init().
All other places must do read() -> mask/set -> write() to not
overwrite existing bits.
This also adds a longer delay for waiting for the microcode
to initialize itself. It seems that the current timeout is sufficient
on all available devices, but there's no real reason why we shouldn't
wait for up to one second. Slow embedded devices might exist.
Better safe than sorry.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Otherwise it may be impossible to connected to an open network after a
resume.
This is a modified version of an original patch by
Alex Eskin <alexeskin@yahoo.com>:
https://bugzilla.redhat.com/show_bug.cgi?id=425950#c8
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
...instead of using AR5K_KEYCACHE_SIZE, which would seem to be a
typo/thinko...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We must also store the ID string (filename) for the cached firmware blobs
and verify that we really have the right firmware cached before using it.
If we don't have the right fw cached, we must free it and request the
correct blobs.
This fixes bandswitch on A/B/G multi-PHY devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This also adds lots of TODOs. Oh well. Lots of work. :)
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes a sparse warning about weird locking.
The spinlock is not needed, so simply remove it.
This also adds some sanity checks to the PHY and radio locking
to protect against recursive locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We are pleased to announce a new Gigabit Ethernet product and its
driver to the linux community. This product is the Intel(R) 82575
Gigabit Ethernet adapter family. Physical adapters will be available
to the public soon. These adapters come in 2- and 4-port versions
(copper PHY) currently. Other variants will be available later.
The 82575 chipset supports significantly different features that
warrant a new driver. The descriptor format is (just like the
ixgbe driver) different. The device can use multiple MSI-X vectors
and multiple queues for both send and receive. This allows us to
optimize some of the driver code specifically as well compared to
the e1000-supported devices.
This version of the igb driver no lnger uses fake netdevices and
incorporates napi_struct members for each ring to do the multi-
queue polling. multi-queue is enabled by default and the driver
supports NAPI mode only.
All the namespace collisions should be gone in this version too. The
register macro's have been condensed to improve readability.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Prefix "bp->phy_flags" names with BNX2_PHY_FLAG_* for consistency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix "bnx2->flags" names with BNX2_* for consistency.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts. We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.
The parallel detect logic is cleaned up slightly to better integrate
the workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct. It happens that they are the same in this
case because we are using the first MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip has problem running in this mode and needs to be disabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
drivers/net/wireless/iwlwifi/iwl-3945.c: In function 'iwl3945_add_radiotap':
drivers/net/wireless/iwlwifi/iwl-3945.c:269: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix rfkill code which caused a use-after-free bug. Thanks to David
Woodhouse for spotting this out.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
libertas: re-pepper debug statementThe recent fluff of updates
didn't put proper lbs_deb_enter/leave calls into the source code.
Add them where appropriate.
Also contains some whitespace changes.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The CF card only has a very old firmware (5.0.16p0). This firmware doesn't
know anything about mesh config. However, current code blindly calls
mesh_config when the card is inserted. So check the firmware version before
issuing this command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Always shows the firmware release.
Also converts the firmware release into something that is easily comparable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
boot2_version is purely USB specific, so move it to struct if_usb_card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
netif_rx should be called only from interrupt context. if_cs and if_sdio receive
packets from other contexts, and thus should call netif_rx_ni.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds lots of N-PHY related lookup tables.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The << and >> operators need space on each side.
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The external iwlwifi driver comes with a README file that is
referenced by the Kconfig. This README is not present in the
driver included in the kernel. Remove references to this
documentation.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch renames iwl3945_rate_scale_priv to iwl3945_rs_sta as it
better represents the purpose of this variable.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1, This patch renames iwl4965_rate_scale_priv to iwl4965_lq_sta.
This type represents a station's link quality.
2. The names of the variables of this type were rs_priv, lq_data, lq, crl
across the file. All are now unified under the name lq_sta.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds iwl_free_fw_desc ucode helper function.
It also moves ucode helper functions to iwl-helpers.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After we delay device initialization until interface up, there are more
conditions for the hardware rf_kill switch states during suspend and
resume. For example, before suspend we can have interface up or down,
rf_kill enable or disable; before resume we can have rf_kill enable or
disable. So there are totally 2^3 = 8 conditions to handle. This patch
addressed this problem and makes sure every condition works correctly.
This patch also merges the device suspend and resume handlers with the
mac_start and mac_stop code since they are basically doing the same
thing.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the firmware loading (read firmware from disk and load
it into the device SRAM) from pci_probe time to the first network
interface open time. There are two reasons for doing this:
1. To support kernel buildin iwlwifi drivers. Because kernel initializes
network devices subsystem before hard disk and SATA subsystem, it is
impossible to get the firmware image from hard disk in the PCI probe
handler. Thus delaying the firmware loading into the network
interface open time is the way to go. Note, we only read the firmware
image from hard disk the first time the interface is open. After this
is succeeded, we cache the firmware image into the host memory. This
is a performance gain when user open and close the interface multiple
times and is necessary for device suspend and resume.
2. For better power saving. When the iwlwifi modules are loaded (or
buildin the kernel) but the wireless network interface is not being
used, it is a good practice the wireless device consumes as less
power as possible. Unloading the firmware from the wireless device
and unregister the driver's interrupt handler in the network
interface close handler provides users a way to achieve this. User
space network configuration tools (i.e NetworkManager) can also
contribute here when it detects a wired cable is connected and
close the wireless interface automatically.
This patch also includes the pci_save/restore_state() fixed by Ian Schram
upon the first version.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Document scan command.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch removes iwl4965_tx_cmd function and splits its content to
iwl4965_hw_build_tx_cmd_rate, iwl4965_build_tx_cmd_basic,
and iwl4965_tl_get_stats function. The latest one will be deprecated
when traffic load will move to rate scale module.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch moves iwl4965_get_dma_hi_address function to iwl-headers.h
as iwl_get_dma_hi_address. This function will be used in more chipsets
than only 4965.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This function removes redundant code in iwl4965_tx_cmd
function, leftovers of previous design.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds code and table data for channel switching on NPHYs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
