| Age | Commit message (Collapse) | Author |
|---|
|
Remove unnecessary status block accesses in tg3_msi(). Since MSI is
not shared, it is unnecessary to read the status block to determine if
there are any new events in the MSI handler. It is also unnecessary to
clear the updated bit in the status block.
Since the poll list is per-cpu, tg3_poll() will be scheduled to run on
the same CPU that received the MSI. Prefetches for the status block
and the next rx descriptors are added in tg3_msi() to improve their
access times when tg3_poll() runs.
In the non-MSI irq handlers, we need to check the status block because
interrupts may be shared. Only prefetches for the next rx descriptors
are added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve ethtool loopback self test by adding PHY loopback to the
existing MAC loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor SerDes bug fixes for 5780S and nvram bug fixes for 5780 and
5752.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This should bits from -mm tree that are affected by pm_message_t
conversion. [I'm not 100% sure I got all of them, but I certainly got all
the errors on make allyesconfig build, and most of warnings, too. I'll go
through the buildlog tommorow and fix any remaining bits].
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
|
|
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
Since the patch to add a NULL short-circuit to crypto_free_tfm() went in,
there's no longer any need for callers of that function to check for NULL.
This patch removes the redundant NULL checks and also a few similar checks
for NULL before calls to kfree() that I ran into while doing the
crypto_free_tfm bits.
I've succesfuly compile tested this patch, and a kernel with the patch
applied boots and runs just fine.
When I posted the patch to LKML (and other lists/people on Cc) it drew the
following comments :
J. Bruce Fields commented
"I've no problem with the auth_gss or nfsv4 bits.--b."
Sridhar Samudrala said
"sctp change looks fine."
Herbert Xu signed off on the patch.
So, I guess this is ready to be dropped into -mm and eventually mainline.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch goes through the current users of the crypto layer and sets
CRYPTO_TFM_REQ_MAY_SLEEP at crypto_alloc_tfm() where all crypto operations
are performed in process context.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is similar to Eric Dumazet's tx_lock patch for tg3 but takes it
one step further to eliminate the tx_lock in the tx_completion path
when the tx queue is not stopped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From: Eric Lemoine <eric.lemoine@gmail.com>
To me the bug is that __LINK_STATE_RX_SCHED can be set while
__netif_rx_schedule() hasen't be called. Why don't fix it in the
simplest way ? See attached patch (absolutely untested).
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This changes the Sun Gem Ether driver's tx ring buffer
length to the proper constant. Currently TX_RING_SIZE
and RX_RING_SIZE are equal, so no malfunction occurs.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently tun/tap only supports the EN10MB ARP type. For use with
wireless and other networking types it should be possible to set the
ARP type via an ioctl.
Patch v2: Included check that the tap interface is down before changing the
link type out from underneath it
Signed-off-by: Mike Kershaw <dragorn@kismetwireless.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
local->hw_priv was initialized only after the interrupt handler was
registered. This could trigger a NULL pointer dereference in
prism2_pccard_card_present() that assumed that local->hw_priv is always
set (and it should have been). Fix this by setting local->hw_priv before
registering the interrupt handler.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver tells sysfs that it's called 'iseries_veth', but if
you ask it via ethtool it thinks it's called 'veth'. I think this comes from
2.4 when the driver was called 'veth', but it's definitely called
'iseries_veth' now, so fix it.
To make sure we don't do it again define DRV_NAME and use it everywhere.
While we're at it, change the version number to 2.0, to reflect the changes
made in this patch series.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Having merged iseries_veth.h, let's remove some of the studly caps that came
with it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
iseries_veth.h is only used by iseries_veth.c, so merge the former into
the latter.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Also to aid debugging, add sysfs support for iseries_veth's port structures.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
To aid in field debugging, add sysfs support for iseries_veth's connection
structures. At the moment this is all read-only, however we could think about
adding write support for some attributes in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
There's a number of problems with the way iseries_veth counts TX errors.
Firstly it counts conditions which aren't really errors as TX errors. This
includes if we don't have a connection struct for the other LPAR, or if the
other LPAR is currently down (or just doesn't want to talk to us). Neither
of these should count as TX errors.
Secondly, it counts one TX error for each LPAR that fails to accept the packet.
This can lead to TX error counts higher than the total number of packets sent
through the interface. This is confusing for users.
This patch fixes that behaviour. The non-error conditions are no longer
counted, and we introduce a new and I think saner meaning to the TX counts.
If a packet is successfully transmitted to any LPAR then it is transmitted
and tx_packets is incremented by 1.
If there is an error transmitting a packet to any LPAR then that is counted
as one error, ie. tx_errors is incremented by 1.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver often has multiple netdevices sending packets over
a single connection to another LPAR. If the bandwidth to the other LPAR is
exceeded, all the netdevices must have their queues stopped.
The current code achieves this by queueing one incoming skb on the
per-netdevice port structure. When the connection is able to send more packets
we iterate through the port structs and flush any packet that is queued,
as well as restarting the associated netdevice's queue.
This arrangement makes less sense now that we have per-connection TX timers,
rather than the per-netdevice generic TX timer.
The new code simply detects when one of the connections is full, and stops
the queue of all associated netdevices. Then when a packet is acked on that
connection (ie. there is space again) all the queues are woken up.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Currently the iseries_veth driver contravenes the specification in
Documentation/networking/driver.txt, in that if packets are not acked by
the other LPAR they will sit around forever.
This patch adds a per-connection timer which fires if we've had no acks for
five seconds. This is superior to the generic TX timer because it catches
the case of a small number of packets being sent and never acked.
This fixes a bug we were seeing on real systems, where some IPv6 neighbour
discovery packets would not be acked and then prevent the module from being
removed, due to skbs lying around.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver uses the generic TX timeout watchdog, however a better
solution is in the works, so remove this code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver can attach to multiple vlans, which correspond to
multiple net devices. However there is only 1 connection between each LPAR,
so the connection structure may be shared by multiple net devices.
This makes module removal messy, because we can't deallocate the connections
until we know there are no net devices still using them. The solution is to
use ref counts on the connections, so we can delete them (actually stop) as
soon as the ref count hits zero.
This patch fixes (part of) a bug we were seeing with IPv6 sending probes to
a dead LPAR, which would then hang us forever due to leftover skbs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch makes veth_init_connection() and veth_destroy_connection()
symmetrical in that they allocate/deallocate the same data.
Currently if there's an error while initialising connections (ie. ENOMEM)
we call veth_module_cleanup(), however this will oops because we call
driver_unregister() before we've called driver_register(). I've never seen
this actually happen though.
So instead we explicitly call veth_destroy_connection() for each connection,
any that have been set up will be deallocated.
We also fix a potential leak if vio_register_driver() fails.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver unconditionally calls dma_unmap_single() even
when the corresponding dma_map_single() may have failed.
Rework the code a bit to keep the return value from dma_unmap_single()
around, and then check if it's a dma_mapping_error() before we do
the dma_unmap_single().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver uses atomic ops to manipulate the in_use field of
one of its per-connection structures. However all references to the
flag occur while the connection's lock is held, so the atomic ops aren't
necessary.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver keeps a stack of messages for each connection
and a lock to protect the stack. However there is also a per-connection lock
which makes the message stack lock redundant.
Remove the message stack lock and document the fact that callers of the
stack-manipulation functions must hold the connection's lock.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Due to a logic bug, once promiscuous mode is enabled in the iseries_veth
driver it is never disabled.
The driver keeps two flags, promiscuous and all_mcast which have exactly the
same effect. This is because we only ever receive packets destined for us,
or multicast packets. So consolidate them into one promiscuous flag for
simplicity.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver contains a state machine which is used to manage
how connections are setup and neogotiated between LPARs.
If one side of a connection resets for some reason, the two LPARs can get
stuck in a race to re-setup the connection. This can lead to the connection
being declared dead by one or both ends. In practice the connection is
declared dead by one or both ends approximately 8/10 times a connection is
reset, although it is rare for connections to be reset.
(an example here: http://michael.ellerman.id.au/files/misc/veth-trace.html)
The core of the problem is that the end that resets the connection doesn't
wait for the other end to become aware of the reset. So the resetting end
starts setting the connection back up, and then receives a reset from the
other end (which is the response to the initial reset). And so on.
We're severely limited in what we can do to fix this. The protocol between
LPARs is essentially fixed, as we have to interoperate with both OS/400
and old Linux drivers. Which also means we need a fix that only changes the
code on one end.
The only fix I've found given that, is to just blindly sleep for a bit when
resetting the connection, in the hope that the other end will get itself
sorted. Needless to say I'd love it if someone has a better idea.
This does work, I've so far been unable to get it to break, whereas without
the fix a reset of one end will lead to a dead connection ~8/10 times.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The iseries_veth driver has a timer which we use to send acks. When the
connection is reset or stopped we need to delete the timer.
Currently we only call del_timer() when resetting a connection, which means
the timer might run again while the connection is being re-setup. As it turns
out that's ok, because the flags the timer consults have been reset.
It's cleaner though to call del_timer_sync() once we've dropped the lock,
although the timer may still run between us dropping the lock and calling
del_timer_sync(), but as above that's ok.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Currently the iseries_veth driver prints the file name and line number in its
error messages. This isn't very useful for most users, so just print
"iseries_veth: message" instead.
- convert uses of veth_printk() to veth_debug()/veth_error()/veth_info()
- make terminology consistent, ie. always refer to LPAR not lpar
- be consistent about printing return codes as %d not %x
- make format strings fit in 80 columns
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Patch from Sascha Hauer
This patch adds support for setting and getting RTS / CTS via
set_mtctrl / get_mctrl functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
BZ# 4475.
|
|
Noted in BZ# 2960.
|
|
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
|
|
Damir Perisa <damir.perisa@solnet.ch> reports:
drivers/net/s2io.h:765: error: invalid lvalue in assignment
drivers/net/s2io.h:766: error: invalid lvalue in assignment
That's a gcc4 error. I don't see why the casts are there anyway..
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Make MODULE_DEVICE_TABLE work for vio devices.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Update version and add 4 minor fixes, the last 2 were suggested by
Jeff Garzik:
1. check for a valid ethernet address before setting it
2. zero out bp->regview if init_one encounters an error and unmaps
the IO address. This prevents remove_one from unmapping again.
3. use netif_rx_schedule() instead of hand coding the same.
4. use IRQ_HANDLED and IRQ_NONE.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change all locks from spin_lock_irqsave() to spin_lock_bh(). All
places that require spinlocks are in BH context.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
