| Age | Commit message (Collapse) | Author |
|---|
|
According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix improper long wait for command completion in pciehp probing.
As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.
This patch changes the pciehp driver to take such command into
account.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit
c27fb883dffe11aa4cb35ecea1fa1832ba45d4da that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the following NULL dereference problem reported from Pierre Ossman
and Ingo Molnar.
pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0
pciehp: pciehp_find_slot: slot (device=0x0) not found
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
IP: [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
PGD 0
Oops: 0000 [1]
CPU 0
Modules linked in:
Pid: 1, comm: swapper Tainted: G W 2.6.26-rc3-sched-devel.git-00001-g2b99b26-dirty #170
RIP: 0010:[<ffffffff80494a8b>] [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP: 0000:ffff81003f83fbb0 EFLAGS: 00010046
RAX: 0000000000000039 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000046
RBP: ffff81003f83fbd0 R08: 0000000000000001 R09: ffffffff80245103
R10: 0000000000000020 R11: 0000000000000000 R12: ffff81003ea53a30
R13: 0000000000000000 R14: 0000000000000011 R15: ffffffff80495926
FS: 0000000000000000(0000) GS:ffffffff80be7400(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000070 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff81003f83e000, task ffff81003f840000)
Stack: 0000000000000008 ffff81003f83fbf6 ffff81003ea53a30 0000000000000008
ffff81003f83fc10 ffffffff80495ab4 0000000000000011 0000000000000002
0000000000000202 0000000000000202 00000000fffffff4 ffff81003ea53a30
Call Trace:
[<ffffffff80495ab4>] pcie_isr+0x18e/0x1bc
[<ffffffff80260831>] request_irq+0x106/0x12f
[<ffffffff80495fb6>] pcie_init+0x15e/0x6cc
[<ffffffff804933a3>] pciehp_probe+0x64/0x541
[<ffffffff8048f4e7>] pcie_port_probe_service+0x4c/0x76
[<ffffffff8054af70>] driver_probe_device+0xd4/0x1f0
[<ffffffff8054b108>] __driver_attach+0x7c/0x7e
[<ffffffff8054b08c>] ? __driver_attach+0x0/0x7e
[<ffffffff8054a4b6>] bus_for_each_dev+0x53/0x7d
[<ffffffff8054ad3c>] driver_attach+0x1c/0x1e
[<ffffffff8054a9c2>] bus_add_driver+0xdd/0x25b
[<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
[<ffffffff8054b288>] driver_register+0x5f/0x13e
[<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
[<ffffffff8048f441>] pcie_port_service_register+0x47/0x49
[<ffffffff80c09d52>] pcied_init+0x15/0x8b
[<ffffffff80bf3938>] kernel_init+0x75/0x243
[<ffffffff808639d2>] ? _spin_unlock_irq+0x2b/0x3a
[<ffffffff80228d1f>] ? finish_task_switch+0x57/0x9a
[<ffffffff8020c258>] child_rip+0xa/0x12
[<ffffffff8020bcec>] ? restore_args+0x0/0x30
[<ffffffff80bf38c3>] ? kernel_init+0x0/0x243
[<ffffffff8020c24e>] ? child_rip+0x0/0x12
Code: 83 80 00 00 00 48 39 f0 75 e1 0f b6 c9 48 c7 c2 00 0e 8d 80 48 c7 c6 8a 60 a6 80 48 c7 c7 10 db a8 80 31 c0 e8 3f 8d d9 ff 31 db <48> 8b 43 70 48 8d 75 ef 48 89 df ff 50 30 80 7d ef 00 74 37 48
RIP [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP <ffff81003f83fbb0>
CR2: 0000000000000070
Kernel panic - not syncing: Fatal exception
The situation under which it occurs is hw and timing related: it appears
to happen on a system that has PCI hotplug hardware but with no active
hotplug cards, and another interrupt in the same (shared) IRQ line
arrives too early, before the hotplug-slot entry has been set up - as
triggered by CONFIG_DEBUG_SHIRQ=y:
This patch contains the following two fixes.
(1) Clear all events bits in Slot Status register to prevent the pciehp
driver from detecting the spurious events that would have been occur
before pciehp loading.
(2) Add check whether slot initialization had been already done.
This is short term fix. We need more structural fixes to install
interrupt handler after slot initialization is done.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
People are confused by the following error message that actually is
not for indicating a error.
Cannot get control of hotplug hardware for pci %s
This patch changes this message to debug message.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
|
|
Current implementation of pciehp_write_cmd() always enables command
completed interrupt. But pciehp_write_cmd() is also used for clearing
command completed interrupt enable bit. In this case, we must not set
the command completed interrupt enable bit. To fix this bug, this
patch add the check to see if caller wants to change command complete
interrupt enable bit.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current shpchp uses the combination of bus number and slot number as a
slot name. But it is not a good idea because bus number is not a
physical identifier but a logical identifier. This is against the shpc
specification. So remove the bus number from the physical identifier.
However, there are some platforms with the problem that it provides
the same slot number. For those platforms, this patch also introduces
new module option 'shpchp_slot_with_bus'. If it is specified, shpchp
uses the combination of bus number and slot number as a slot name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
this_patch_makes_the_needlessly_global_pciehp_acpi_get_hp_hw_control_from_firmware_static
;)
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Clean up pciehp_ini(). This patch is trying to
- Remove redundant capablity checks that were already done in PCIe
port bus driver.
- Separate the code only for debugging and make debug information
easier to read.
- Make the entire code easier to read and understand what it is doing.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We must disable hotplug interrupt at controller relase time, otherwise
spurious interrupts might happen if any slot events occured (e.g. MRL
change) after unloading pciehp driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Hotplug interrupt is enabled at initialization and nobody clears it.
So we need to setup it in each command. This patch removes redundant
codes about this.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp saves only 8bits of Slot Capability registers in
ctrl->ctrlcap. But it refers more than 8bit for checking EMI capability.
It is clearly a bug and EMI would never work. To fix this problem,
this patch saves full Slot Capability contens in ctrl->slot_cap. It also
reduce the redundant reads of Slot Capability register. And this pach
also cleans up the macros to check the slot capabilitys (e.g. MRL_SENS(),
and so on).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp implementaion clears hotplug events without waiting for
command completion. Because of this, events might not be cleared properly.
To prevent this problem, we must use pciehp_write_cmd() to write to
Slot Control register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the possible race condition between pcie_isr() and pciehp_write_cmd()
because of the lack of memory barrier.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp implementation disables and re-enables hotplug interrupts
in its interrupt handler. This operation might be intend to guarantee
that interrupts for the events newly occured during previous events are
being handled will be successfully generated. But current implementaion
has the following prolems.
- Current interrupt service routin clears status changes without
waiting command completion. Because of this, events might not be
cleared properly.
- Current interrupt service routine clears status changes caused by
disabling or enabling hotplug interrupts itself. This will lose new
events that occurs during previous interrupts are being handled.
- Current implementation doesn't have any serialization mechanism
between the code to wait for command completion and the interrupt
handler that clears the command completion events caused by itself.
There is clearly race conditions between them, and it may cause
the problem that waiting for command completion doesn't work for
example.
To fix those problems, this patch stops disabling/re-enabling hotplug
interrupts in interrupt service routine. Instead of this, this patch
re-inspects Slot Status register after clearing what is presumed to
be the last bending interrupt in order to guarantee that all interrupt
events are serviced.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp uses the combination of bus number and slot number as a
slot name. But it is not a good idea because bus number is not a
physical identifier but a logical identifier. This is against the PCIE
specification. So remove the bus number from the physical identifier.
However, there are some platforms with the problem that it provides
the same slot number. For those platforms, this patch also introduces
new module option 'pciehp_slot_with_bus'. If it is specified, pciehp
uses the combination of bus number and slot number as a slot name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The 'power' attribute of the fakephp driver originally only let one turn a
slot off. If one tried to turn a slot on (echo 1 > .../power), it would
return ENODEV, as fakephp did not support this function.
An old (pre-git) patch changed this:
2004/11/11 16:33:31-08:00 jdittmer
[PATCH] fakephp: add pci bus rescan ability
http://article.gmane.org/gmane.linux.kernel/251183
Now writing "1" to the power attribute has the effect of triggering a bus
rescan, but it still returns ENODEV, probably an oversight in the above
patch.
Using the BusyBox echo will not produce an error message, but will
trigger *two* bus rescans (and return an exit code of 1):
~ # strace echo -n 1 > /sys/bus/pci/slots/0000:00:00.0/power
...
write(1, "1", 1) = -1 ENODEV (No such device)
write(1, "1", 1) = -1 ENODEV (No such device)
exit(1) = ?
Using cp gives a write error, even though the write did happen and a rescan
was triggered:
~ # echo -n 1 > tmp ; cp tmp /sys/bus/pci/slots/0000:00:00.0/power
cp: Write Error: No such device
It seems much better to return success instead of failure. The actual
status of the bus rescan is hard to return. It happens asynchronously in a
work thread, so the sysfs store functions returns before any status is
ready (the whole point of the work queue). And even if it didn't do this,
the rescan doesn't have any clear status to return.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Jan Dittmer <jdittmer@ppp0.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In drivers/pci/hotplug/ibmphp_core.c::ibmphp_init_devno() we allocate
space dynamically for a PCI irq routing table by calling
pcibios_get_irq_routing_table(), but we never free the allocated space.
This patch frees the allocated space at the function exit points.
Spotted by the Coverity checker. Compile tested only.
Please consider applying.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This was marked incorrectly for some reason. Allow the ibmphp driver to
be built even if PCI_LEGACY is not enabled.
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This removes the depandancy of the cpcihp driver from the PCI_LEGACY
config option by removing its usage of the pci_find_bus() function.
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This fixes a 2.6.25 regression reported by Alex Chiang.
Invoke pciehp_enable_slot() at startup only when pciehp_force=1.
Some HP equipment apparently cannot cope with it otherwise.
This restores the (previously working) 2.6.24 behaviour here,
while allowing machines that need a kick to use pciehp_force=1.
This was the original design back in October 2007,
but Kristen suggested we try without it first:
Kristen Carlson Accardi wrote:
>I think it would be ok to try allowing the slot to be enabled when not
>using pciehp_force mode. We can wrap it later if it proves to break things
This ended up breaking one of Alex's setups,
so it's time to put the wrapper back in now.
Signed-off-by: Mark Lord <mlord@pobox.com>
Acked-by: Alex Chiang <achiang@hp.com>
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In drivers/pci/hotplug/ibmphp_ebda.c::ebda_rsrc_controller(), storage is
allocated with kzalloc() and assigned to 'tmp_slot'. Then lots of
stuff, like ->flag, ->supported_speed etc is set in tmp_slot. A bit
further down there's then this test :
if (!bus_info_ptr1) {
rc = -ENODEV;
goto error;
}
At this point, tmp_slot has not been assigned to anything, so when
erroring-out we want to free it, but nothing at the 'error:' label
free's 'tmp_slot' - and we can't really free 'tmp_slot' at 'error:'
since we may jump to that label later when 'tmp_slot' *has* been used
and we do not want it freed. So, the only sane option left seems to be
to kfree(tmp_slot) just before jumping to the 'error:' label in the one
place where this is what actually makes sense. The following patch does
just that and thus kills off a tiny potential memory leak.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix the error code path in hpc_power_off_slot().
The Bad DLLP Mask bit must be restored before return.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix following warning:
WARNING: vmlinux.o(.text+0x47bdb1): Section mismatch in reference from the function pci_scan_child_bus() to the function .devinit.text:pcibios_fixup_bus()
We had plenty of functions that could be annotated __devinit but due to
the former restriction that exported symbols could not be annotated
they were not so. So annotate these function and fix the references
from the pci/hotplug/* code to silence the resuting warnings.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When acpi=off and pci=nomsi, don't load acpiphp.
Fixes this:
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread
FFFF81103CC54000 could not acquire Mutex [1] [20070126]
[akpm@linux-foundation.org: export acpi_pci_disabled for acpiphp.ko]
[akpm@linux-foundation.org: fix return statement]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/pci/hotplug/acpiphp_ibm.c:ibm_find_acpi_device() is not
large enough to accommodate data returned by the _CID method
executed from acpi_get_object_info().
This patch eliminates the problem by letting ACPI code
(instead of driver code) determine and obtain a correctly
sized buffer.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If the fakephp driver is used to emulate removal of a PCI device by
writing text string "0" to the "power" sysfs attribute file, this causes
its parent directory and its contents (including the "power" file) to be
deleted before the write operation returns. Unfortunately, it ends up
in a deadlock waiting for itself to complete.
The deadlock is as follows: sysfs_write_file calls flush_write_buffer
which calls sysfs_get_active_two before calling power_write_file in
pci_hotplug_core.c via the sysfs store operation. The power_write_file
function calls disable_slot in fakephp.c via the slot operation. The
disable_slot function calls remove_slot which calls pci_hp_deregister
(back in pci_hotplug_core.c) which calls fs_remove_slot which calls
sysfs_remove_file to remove the "power" file. The sysfs_remove_file
function calls sysfs_hash_and_remove which calls sysfs_addrm_finish
which calls sysfs_deactivate. The sysfs_deactivate function sees that
something has an active reference on the sysfs_dirent (from the
previous call to sysfs_get_active_two back up the call stack somewhere)
so waits for the active reference to go away, which is of course
impossible.
The problem has been present since 2.6.21.
This patch breaks the deadlock by queuing work queue items on a single-
threaded work queue to remove a slot from sysfs, and to rescan the PCI
buses. There is also some protection against disabling a slot that is
already being removed.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Disable Bus Master, SERR# and INTx to ensure that no new Requests will
be generated from the device before turning power off, in accordance
with the specification.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Set Bad DLLP Mask bit in Correctable Error Mask Register during
turning power off the slot.
This is the workaround against Bad DLLP error that sometimes happen
during turning power off on the slot which conforms to PCI Express
1.0a spec. The cause of this error seems that PCI Express 1.0a spec
doesn't have the following consideration that was added to PCI Express
1.1 spec.
"If the port is associated with a hot-pluggable slot (Hot-Plug
Capable bit in the Slot Capabilities register set to 1b), and
Power Controller Control bit in Slot Control register is 1b(Off),
then any transition to DL Inactive must not be considered an
error."
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
After turning power off, we must wait for at least 1 second *before*
LED operation.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
PCIeHP: Fix some whitespace damage
Signed-off-by: Rolf Eike Beer <eike-hotplug@sf-tec.de>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove duplicated code to find an extend capability in PCIEHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove needless hp_slot calculation. This has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove needless members from struct controller. This has no functional
changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
acpi_get_name() is called before and after dbg(). The latter is
useless and should be removed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
fix trivial typos.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Earlier patches to split out the hardware init for PCIe hotplug resulted in
some one-time initializations being redone on every resume cycle. Eg.
irq/polling initialization.
This patch splits the hardware init into two parts, and separates the
one-time initializations from those so that they only ever get done once,
as intended.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Make use of the previously split out pcie_init_enable_events() function
to reinitialize the hotplug hardware on resume from suspend, but only
when pciehp_force==1. Otherwise behaviour is unmodified.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Dell notebooks (and others?) in conjunction with modparam of pciehp_force=1
Split out the hotplug hardware initialization code from pcie_init()
into pcie_init_enable_events(), without changing any functionality.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
notebooks (and others?) in conjunction with modparam of pciehp_force=1.
Fix pciehp_probe() to deal with ExpressCard cards
that were inserted prior to the driver being loaded.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix presentation of the slot number in the /sys/bus/pci/slots
directory to match that used in the majority of other drivers.
> Greg said:
> How is anyone supposed to write sane managability tools in the
> presence
> of such anarchy?
>
> > ~ # cat /sys/bus/pci/slots/0000:00:02.2/phy_location
> > U787A.001.DNZ00Z5-P1-C2
>
> Right. This should look like:
>
> # cat /sys/bus/pci/slots/U787A.001.DNZ00Z5-P1-C2/address
> 0000:00:02
This patch implements exactly what you describe. Boot tested.
I assume you really mean it -- if so, then please review and
ack the patch !?
I have absolutely no clue if this breaks any existing IBM tools.
I'm pretty sure it doesn't ... but attention Mike Strosaker! does it?
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: <strosake@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently, fakephp will claim all devices; we really only want it
to claim those not in slots.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove superfluous space.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove unused variable from acpiphp.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove EXPERIMENTAL from PCI Hot Plug.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Thank you so much for your check & advise.
This time, I've tried on ibmphp_core.c, is it OK?
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
