aboutsummaryrefslogtreecommitdiff
path: root/drivers/pci
AgeCommit message (Collapse)Author
2006-06-21[PATCH] PCI: don't enable device if already enabledKristen Accardi
If a device is already enabled, don't bother reenabling it. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Acked-By: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] PCI: Add a "enable" sysfs attribute to the pci devices to allow ↵Arjan van de Ven
userspace (Xorg) to enable devices without doing foul direct access This patch adds an "enable" sysfs attribute to each PCI device. When read it shows the "enabled-ness" of the device, but you can write a "0" into it to disable a device, and a "1" to enable it. This later is needed for X and other cases where userspace wants to enable the BARs on a device (typical example: to run the video bios on a secundary head). Right now X does all this "by hand" via bitbanging, that's just evil. This allows X to no longer do that but to just let the kernel do this. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> CC: Peter Jones <pjones@redhat.com> Acked-by: Dave Airlie <airlied@linux.ie> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] PCI: Add pci_assign_resource_fixed -- allow fixed address assignmentsKumar Gala
PCI: Add pci_assign_resource_fixed -- allow fixed address assignments On some embedded systems the PCI address for hotplug devices are not only known a priori but are required to be at a given PCI address for other master in the system to be able to access. An example of such a system would be an FPGA which is setup from user space after the system has booted. The FPGA may be access by DSPs in the system and those DSPs expect the FPGA at a fixed PCI address. Added pci_assign_resource_fixed() as a way to allow assignment of the PCI devices's BARs at fixed PCI addresses. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] PCI: fix to pci ignore pre-set 64-bit bars on 32-bit platformsBjorn Helgaas
When we detect a 64-bit pre-set address in a BAR on a 32-bit platform, we disable it and treat it as if it had been unset, thus allowing the general address assignment code to assign a new address to it when the device is enabled. This can happen either if the firmware assigns 64-bit addresses; additionally, some cards have been found "in the wild" which do not come out of reset with all the BAR registers set to zero. Unfortunately, the patch that implemented this tested the low part of the address instead of the high part of the address. This patch fixes that. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] PCI: Ignore pre-set 64-bit BARs on 32-bit platformsH. Peter Anvin
[pci] Ignore pre-set 64-bit BARs on 32-bit platforms Currently, Linux always rejects a device which has a pre-set 64-bit address on a 32-bit platform. On systems which do not do PCI initialization in firmware, this causes some devices which don't correctly power up with all BARs zero to fail. This patch makes the kernel automatically zero out such an address (thus treating it as if it had not been set at all, meaning it will assign an address if necessary). I have done this only for devices, not bridges. It seems potentially hazardous to do for bridges. Signed-off-by: H. Peter Anvin <hpa@c2micro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] PCI: altix: msi supportMark Maule
MSI callouts for altix. Involves a fair amount of code reorg in sn irq.c code as well as adding some extensions to the altix PCI provider abstaction. Signed-off-by: Mark Maule <maule@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] PCI: per-platform IA64_{FIRST,LAST}_DEVICE_VECTOR definitionsMark Maule
Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms use a subset of the IA64 range. Implement this by making the above macros global variables which the platform can override in it setup code. Also add a reserve_irq_vector() routine used by SN to mark a vector's as in-use when that weren't allocated through assign_irq_vector(). Signed-off-by: Mark Maule <maule@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] PCI: msi abstractions and support for altixMark Maule
Abstract portions of the MSI core for platforms that do not use standard APIC interrupt controllers. This is implemented through a new arch-specific msi setup routine, and a set of msi ops which can be set on a per platform basis. Signed-off-by: Mark Maule <maule@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (30 commits) [PATCH] PCI Hotplug: Fix recovery path from errors during pcie_init() [PATCH] PCI Hotplug: fake NULL pointer dereferences in IBM Hot Plug Controller Driver [PATCH] shpchp: Cleanup improper info messages [PATCH] shpchp: Remove Unused hpc_evelnt_lock [PATCH] shpchp: Cleanup interrupt polling timer [PATCH] shpchp: Cleanup SHPC commands [PATCH] shpchp: Cleanup interrupt handler [PATCH] shpchp: Remove unnecessary hpc_ctlr_handle check [PATCH] pciehp: Implement get_address callback [PATCH] pciehp: Add missing pci_dev_put [PATCH] pciehp: Replace pci_find_slot() with pci_get_slot() [PATCH] SGI Hotplug: Incorrect power status [PATCH] shpchp: Create shpchpd at controller probe time [PATCH] shpchp: Mask Global SERR and Intr at controller release time [PATCH] SHPC: Fix SHPC Contoller SERR-INT Register bits access [PATCH] SHPC: Fix SHPC Logical Slot Register bits access [PATCH] SHPC: Cleanup SHPC Logical Slot Register bits access [PATCH] SHPC: Cleanup SHPC Logical Slot Register access [PATCH] SHPC: Cleanup SHPC register access [PATCH] pciehp: Fix programming hotplug parameters ...
2006-06-19[PATCH] PCI Hotplug: Fix recovery path from errors during pcie_init()Jan Beulich
Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] PCI Hotplug: fake NULL pointer dereferences in IBM Hot Plug ↵Eric Sesterhenn
Controller Driver Remove checks for value, since the hotplug core always provides a valid value. Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Cleanup improper info messagesKenji Kaneshige
Current SHPCHP driver shows device number of slots in info messages, but it is useless and should be replaced with slot name. This patch replaces the device number shown in the info messages with the slot name. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Remove Unused hpc_evelnt_lockKenji Kaneshige
This patch removes unused hpc_event_lock. This patch has no functional change. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Cleanup interrupt polling timerKenji Kaneshige
This patch cleans up the interrupt polling timer code in shpchp_hpc.c. This has no functional changes. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Cleanup SHPC commandsKenji Kaneshige
This patch cleans up the code related to issuing SHPC commands. This patch has no functional changes. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Cleanup interrupt handlerKenji Kaneshige
This patch cleans up the interrupt handler of shpchp driver. This patch has no functional changes. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Remove unnecessary hpc_ctlr_handle checkKenji Kaneshige
This patch removes unnecessary error check for hpc_ctlr_handle. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] pciehp: Implement get_address callbackKenji Kaneshige
This patch implements .get_address callback of hotplug_slot_ops for PCIEHP driver. With this patch, we can see bus address of hotplug slots as follows: # cat /sys/bus/pci/slots/0010_0000/address 0000:0a:00 Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] pciehp: Add missing pci_dev_putKenji Kaneshige
The PCIEHP driver leaks reference counter of pci_dev structures. This patch adds missing pci_dev_put() calls to PCIEHP driver. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] pciehp: Replace pci_find_slot() with pci_get_slot()Kenji Kaneshige
This patch replaces pci_find_slot() with pci_get_slot() in PCIEHP driver. This patch enables PCI Express Hotplug on the system which has multiple PCI domains. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] SGI Hotplug: Incorrect power statusMike Habeck
This is a repost of a patch submitted by Prarit Bhargava on 01-19-06 that never got integrated. The get_power_status function is currently reporting a bitwise mapping of the slot if the slot is powered on. It should return 1 if powered on and 0 if powered off. Signed-off-by: Mike Habeck <habeck@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Create shpchpd at controller probe timeKenji Kaneshige
The workqueue thread of shpchp driver should be created only when SHPC based hotplug slots are detected on the system. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] shpchp: Mask Global SERR and Intr at controller release timeKenji Kaneshige
Global SERR and Interrupt should be masked at shpchp driver unload time. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] SHPC: Fix SHPC Contoller SERR-INT Register bits accessKenji Kaneshige
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits in controller SERR-INT register. This might cause unpredicable results. This patch fixes this bug. [*] RsvdP and RsvdZ are defined in SHPC spec as follows: RsvdP - Reserved and Preserved. Register bits of this type are reserved for future use as R/W bits. The value read is undefined. Writes are ignored. Software must follow These rules when accessing RsvdP bits: - Software must ignore RsvdP bits when testing values read from these registers. - Software must not depend on RsvdP bit's ability to retain information when written - Software must always write back the value read in the RsvdP bits when writing one of these registers. RsvdZ - Reserved and Zero. Register bits of this type are reserved for future use as R/WC bits. The value read is undefined. Writes are ignored. Software must follow these rules when accessing RsvdZ bits: - Software must ignore RsvdZ bits when testing values read from these registers. - Software must not depends on a RsvdZ bit's ability to retain information when written. - Software must always write 0 to RsvdZ bits when writing one of these register. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] SHPC: Fix SHPC Logical Slot Register bits accessKenji Kaneshige
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits in logical slot registers. This might cause unpredicable results. This patch fixes this bug. [*] RsvdP and RsvdZ are defined in SHPC spec as follows: RsvdP - Reserved and Preserved. Register bits of this type are reserved for future use as R/W bits. The value read is undefined. Writes are ignored. Software must follow These rules when accessing RsvdP bits: - Software must ignore RsvdP bits when testing values read from these registers. - Software must not depend on RsvdP bit's ability to retain information when written - Software must always write back the value read in the RsvdP bits when writing one of these registers. RsvdZ - Reserved and Zero. Register bits of this type are reserved for future use as R/WC bits. The value read is undefined. Writes are ignored. Software must follow these rules when accessing RsvdZ bits: - Software must ignore RsvdZ bits when testing values read from these registers. - Software must not depends on a RsvdZ bit's ability to retain information when written. - Software must always write 0 to RsvdZ bits when writing one of these register. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] SHPC: Cleanup SHPC Logical Slot Register bits accessKenji Kaneshige
This patch cleans up the code to access bits in slot logical registers. This patch has no functional change. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] SHPC: Cleanup SHPC Logical Slot Register accessKenji Kaneshige
This patch cleans up the code to access slot logical registers. This patch has no functional changes. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] SHPC: Cleanup SHPC register accessKenji Kaneshige
This patch cleans up the code to access SHPC working register sets. This patch has no functional changes. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] pciehp: Fix programming hotplug parametersKenji Kaneshige
Current PCHEHP driver doesn't have any code to program hotplug parameters from firmware. So hotplug parameters are never programed at hot-add time. This patch add support for programming hotplug parameters to PCIEHP driver. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] acpi_pcihp: Add support for _HPXKenji Kaneshige
This patch adds support for _HPX (Hot Plug Parameter Extensions) defined in ACPI3.0a spec. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] acpi_pcihp: Remove improper error message about OSHPKenji Kaneshige
This patch converts the improper error message about OSHP evaluation to debug message which is displayed only when pci_hotplug.ko is loaded with debugging mode enabled. To do this, this patch adds a new module parameter "debug_acpi" to pci_hotplug.ko for enabling/disabling debug messages in acpi_pcihp.c. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] acpi_pcihp: Fix programming _HPP valuesKenji Kaneshige
This patch fixes the problem that hotplug parameters are not programed when PCI cards are hot-added by ACPIPHP, SHPCHP and PCIEHP driver. The pci_dev structure being hot-added is not bound to ACPI handle, so we need to trace PCI bus tree to find ACPI handle. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] pciehp: dont call pci_enable_devKristen Accardi
Don't call pci_enable_device from pciehp because the pcie port service driver already does this. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] PCI Hotplug: don't use acpi_os_freeKristen Accardi
acpi_os_free should not be used by drivers outside of acpi/*/*.c. Replace with kfree(). Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] acpiphp: turn off slot power at error caseMUNEDA Takahiro
When acpiphp_enable_slot() is failed, acpiphp does not change the slot->flags. Therefore, when user tries to read power status, acpiphp_get_power_status() returns the enable status whether the slot is not really enabled. This patch fixes this BUG. Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] acpiphp: host and p2p hotplugMUNEDA Takahiro
I encountered the problem that when there are some hotplug slots are under the host bridge, the hotplug slots under the p2p bridge are not treated as hotpluggable. This patch fixes this BUG. Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] acpiphp: hotplug slot hotplugMUNEDA Takahiro
o hotplug slots add When the hot-added PCI device is p2p bridge, acpiphp calls find_p2p_bridge() to add hotplug slots. o hotplug slots remove When the hot-removing PCI device is p2p bridge, acpiphp calls cleanup_p2p_bridge() to remove hotplug slots. o notify handler exchange When the p2p bridge is added, acpiphp changes the notify hanlder. If no bridge device is inserted into the hotpluggable PCI slot, acpiphp installs the notify handler for function. After the p2p bridge hot-add, acpiphp has to install the notify handler for bridge. Because, the role of the handlers are not same. The hot-remove case is ditto. Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] acpiphp: configure _PRT - V3MUNEDA Takahiro
Current acpiphp does not free acpi_device structs when the PCI devices are removed. When the PCI device is added, acpi_bus_add() fails because acpi_device struct has already exists. So, _PRT method does not evaluate. This patch fixes this issue. Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[PATCH] PCI Hotplug: Tollhouse HP: SGI hotplug driver changesPrarit Bhargava
SGI hotplug driver changes required to support Tollhouse system PCI hotplug, and implements the PRF_HOTPLUG_SUPPORT feature bit. Signed-off-by: Prarit Bhargava <prarit@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-13Merge branch 'master' into upstreamJeff Garzik
2006-06-11[PATCH] PCI: reverse pci config space restore orderYu, Luming
According to Intel ICH spec, there are several rules that Base Address should be programmed before IOSE (PCICMD register ) enabled. For example ICH7: 12.1.3 SATA : the base address register for the bus master register should be programmed before this bit is set. 11.1.3: PCICMD (USB): The base address register for USB should be programmed before this bit is set. .... To make sure kernel code follow this rule , and prevent unnecessary confusion. I proposal this patch. Signed-off-by: Luming Yu <luming.yu@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-11[PATCH] PCI: Improve PCI config space writebackDave Jones
At least one laptop blew up on resume from suspend with a black screen due to a lack of this patch. By only writing back config space that is different, we minimise the possibility of accidents like this. Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-11[PATCH] PCI: Error handling on PCI device resumeJean Delvare
We currently don't handle errors properly when resuming a PCI device: * In pci_default_resume() we capture the error code returned by pci_enable_device() but don't pass it up to the caller. Introduced by commit 95a629657dbe28e44a312c47815b3dc3f1ce0970 * In pci_resume_device(), the errors possibly returned by the driver's .resume method or by the generic pci_default_resume() function are ignored. This patch fixes both issues. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-24[PATCH] Revive pci_find_ext_capabilityBrice Goglin
This patch revives pci_find_ext_capability (has been disabled a couple month ago since it was not used anywhere. See http://lkml.org/lkml/2006/1/20/247). It will now be used by the myri10ge driver. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Andrew J. Gallatin <gallatin@myri.com> drivers/pci/pci.c | 3 +-- include/linux/pci.h | 2 ++ 2 files changed, 3 insertions(+), 2 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-21[PATCH] pci: correctly allocate return buffers for osc callsKristen Accardi
The OSC set and query functions do not allocate enough space for return values, and set the output buffer length to a false, too large value. This causes the acpi-ca code to assume that the output buffer is larger than it actually is, and overwrite memory when copying acpi return buffers into this caller provided buffer. In some cases this can cause kernel oops if the memory that is overwritten is a pointer. This patch will change these calls to use a dynamically allocated output buffer, thus allowing the acpi-ca code to decide how much space is needed. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Cc: "Brown, Len" <len.brown@intel.com> Cc: "Yu, Luming" <luming.yu@intel.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-15[PATCH] smbus unhiding kills thermal managementCarl-Daniel Hailfinger
Do not enable the SMBus device on Asus boards if suspend is used. We do not reenable the device on resume, leading to all sorts of undesirable effects, the worst being a total fan failure after resume on Samsung P35 laptop. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Signed-off-by: Pavel Machek <pavel@suse.cz> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-15[PATCH] VIA quirk fixup, additional PCI IDsChris Wedgwood
An earlier commit (75cf7456dd87335f574dcd53c4ae616a2ad71a11) changed an overly-zealous PCI quirk to only poke those VIA devices that need it. However, some PCI devices were not included in what I hope is now the full list. Consequently we're failing to run the quirk on all machines which need it, causing IRQ routing failures. This should I hope correct this. Thanks to Masoud Sharbiani <masouds@masoud.ir> for pointing this out and testing the fix. Signed-off-by: Chris Wedgwood <cw@f00f.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-27[PATCH] PCI quirk: VIA IRQ fixup should only run for VIA southbridgesChris Wedgwood
Alan Cox pointed out that the VIA 'IRQ fixup' was erroneously running on my system which has no VIA southbridge (but I do have a VIA IEEE 1394 device). This should address that. I also changed "Via IRQ" to "VIA IRQ" (initially I read Via as a capitalized via (by way/means of). Signed-off-by: Chris Wedgwood <cw@f00f.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-04-27[PATCH] PCI: fix potential resource leak in drivers/pci/msi.cJesper Juhl
The coverity checker spotted (as entry #599) that we might leak `entry' in drivers/pci/msi.c::msix_capability_init() This patch should take care of that. Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-04-20[PATCH] MSI-K8T-Neo2-Fir OnboardSound and additional SoundcardJohannes Goecke
On the MSI-K8T-NEO2 FIR ( Athlon-64, Socket 939 with VIA-K8T800- Chipset and onboard Sound,... ) the BIOS lets you choose "DISABLED" or "AUTO" for the On-Board Sound Device. If you add another PCI-Sound-Card the BIOS disables the on-board device. So far I have a Quirk, that does set the correspondent BIT in the PCI-registers to enable the soundcard. But how to ensure that the code is executed ONLY on excactly this kind of boards (not any other with similar Chipset)? Cc: Jaroslav Kysela <perex@suse.cz> Acked-by: Takashi Iwai <tiwai@suse.de> Cc: Lee Revell <rlrevell@joe-job.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>