| Age | Commit message (Collapse) | Author |
|---|
|
Add support for a new lpfc soft_wwpn sysfs attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
fast_io_fail_tmo_callbk
Add support for new dev_loss_tmo callback
Goodness is that it removes code for a parallel nodev timer that
existed in the driver
Add support for the new fast_io_fail callback
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Add support to post events via new FC event interfaces
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
supported targets
Standardize the driver on a single define for the maximum supported targets.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This removes the duplicate functionality which had been added to
the lpfc driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
dual channel adapters
Introduce lpfc_reset_barrier() function for resets on dual channel adapters
Workaround for a hardware errata on dual channel asics. There is a
potential for the chip to lock up on a reset if a shared dma engine is in
use. The (ugly) work around requires a reset process which uses a mailbox
command to synchronize the independent channels prior to the reset to
avoid the issue. Unfortunately, the timing windows required to ensure this
workaround succeeds are very specific, meaning we can't release the cpu
during the barrier.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Fix performance when using multiple SLI rings
Currently the driver allocates all of its SLI command and response ring
entries to one primary ring. Other rings get little, or no, resources.
Allow more resources to be given to ring 1
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Add ERROR and WARM_START modes for diagnostic purposes.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Remove hba_list from struct lpfc_hba
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Misc FC Discovery changes :
- Added FC_BYPASSED_MODE statistic
- Corrected some log message data
- Fix up Discovery infrastructure to support FAN:
Allow Fabric entities to flow thru DSM
Fix up linkup/linkdown unregister login processing for Fabric entities
Clean up Discovery code
Utilize nodev_tmo for Fabric entities
- Use of 3 * ratov for CT handling timeouts
- Fix up DSM to make more appropriate decisions and clean up code.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Handling of ELS commands RRQ, RPS, RPL and LIRR correctly
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Remove unreferenced cfg_fcp_bind_method from struct lpfc_hba
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
overloading
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
- Add functionality to run in polled mode only. Includes run time
attribute to enable mode.
- Enable runtime writable hba settings for coallescing and delay parameters
Customers have requested a mode in the driver to run strictly polled.
This is generally to support an environment where the server is extremely
loaded and is looking to reclaim some cpu cycles from adapter interrupt
handling.
This patch adds a new "poll" attribute, and the following behavior:
if value is 0 (default):
The driver uses the normal method for i/o completion. It uses the
firmware feature of interrupt coalesing. The firmware allows a
minimum number of i/o completions before an interrupt, or a maximum
time delay between interrupts. By default, the driver sets these
to no delay (disabled) or 1 i/o - meaning coalescing is disabled.
Attributes were provided to change the coalescing values, but it was
a module-load time only and global across all adapters.
This patch allows them to be writable on a per-adapter basis.
if value is 1 :
Interrupts are left enabled, expecting that the user has tuned the
interrupt coalescing values. When this setting is enabled, the driver
will attempt to service completed i/o whenever new i/o is submitted
to the adapter. If the coalescing values are large, and the i/o
generation rate steady, an interrupt will be avoided by servicing
completed i/o prior to the coalescing thresholds kicking in. However,
if the i/o completion load is high enough or i/o generation slow, the
coalescion values will ensure that completed i/o is serviced in a timely
fashion.
if value is 3 :
Turns off FCP i/o interrupts altogether. The coalescing values now have
no effect. A new attribute "poll_tmo" (default 10ms) exists to set
the polling interval for i/o completion. When this setting is enabled,
the driver will attempt to service completed i/o and restart the
interval timer whenever new i/o is submitted. This behavior allows for
servicing of completed i/o sooner than the interval timer, but ensures
that if no i/o is being issued, then the interval timer will kick in
to service the outstanding i/o.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
- Release task management command before counting outstanding commands.
TMF was being erroneously counted as an active outstanding command.
- Serialize EH calls and block requests when EH function is running.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Table was not providing a lot of value and injected a couple of
errors. Removed it and made functionality inline.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Fix panic in lpfc_get_stats()
Symptoms: Panic on sysfs stats access
Cause: In lpfc_get_stats() we are writing to memory that we do not
own.
Fix: Fix our stats structure allocation. Embed phba->link_stats in
struct lpfc_hba and stop treating it like rogue structure.
Note: Embedding midlayer/transport structure in our structure caused
need for more files to include midlayer/transport headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Update copyright notice text and include year 2005.
Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
From: James.Smart@Emulex.Com
Modified for kernel import and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
