| Age | Commit message (Collapse) | Author |
|---|
|
Minor fixes addressing:
- rport managements during vport deletion.
- acquire proper physical-ha during qla24xx_abort_command() and
qla24xx_queuecommand()
- do not needlessly acquire the pha for non-NPIV capable ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
As the original code would incorrectly call the non-ISP24xx/25xx
callbacks during recovery, a stop-firmware failure could result
in improper bit-banging of the RISC and in some cases manifest in
a NMI-watchdog trigger due to the RISC not coming out of its
reset state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Use the full buffer size available, as there's no reason to limit
the firwmare-image load-segment size for these parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add an additional check to verify that the current executing
firmware is in fact non-ROM code. The non-ROM Get-ID mailbox
command is used for verification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
loop-resync.
There were several issues here, one, during RSCN handling if a
follow-on RSCN occurred (within interrupt context) the DPC thread
could inadvertantly leave the fcport in a stale lost state.
Secondly, scheduled rport removal is handled exclusively by the
'parent' DPC thread, so wake up the proper thread. Finally,
process vport loop-resync's only when the vport has in an
"active" state (ID acquired).
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
While issuing a marker, manipulating the request/response queues
and modifying the outstanding command array.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The firmware group has suggested that FCE (Fibre Channel Event)
tracing be enabled prior to EFT (Extended Firmware Tracing) to
maximize the capturing of data on the wire. This change has no
real semantic effect on driver operation, as it's mostly a
shuffling of code.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Recent ISPs have this information written at manufacturing time,
so use the information. This also reduces future churn of the
qla_devtbl.h file contents, as the driver can now depend on the
information to be present in VPD.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
iIDMA support requires the driver issue several additional
fabric-managegment (FM) commands per port discovered during SNS
scanning -- GFPN (Get Fabric Port Name) and GPSC (Get Port Speed
Capabilities). It has been found during testing that some
switches do not respond as *well* as expected to these commands
(silence -- no ACC nor BS_RJT). So, to handle such conditions,
allow the user the ability to indirectly disable the FM commands
by disabling iIDMA with the ql2xiidmaenable module-parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This parameter counts the total number of ISP aborts during
driver execution. The value is exported through a DEVICE_ATTR()
off the scsi_host.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There were several places in the driver which could cause byte
ordering problem as provided by Al Viro
<viro@ZenIV.linux.org.uk>.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There were several places where referencing ha structure of
virtual ports for resources. Among those refereces, certain
fields are get up-to-dated only on ha structure of physical port.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The Flash Descriptor Table (FDT) present on many recent HBAs
encodes flash accessing characteristics of the flash-part used on
the HBA. Use this information during flash manipulation (writes)
rather than using specific hard-coded values based on queried
manufacturer and device IDs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Strip unused (DEBUG-ONLY) enabled functions, inlines, useless
wrappers, and unused DPC flags from the code. Another step in
the migration towards a cleaner (less-crusty) driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Recent ISPs have a region within FLASH which acts as a repository
for the logging of serious hardware and software failures.
Currently, the region is large enough to support up to 255
entries.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
driver.
Rather than using a duplicate/cached value stored in the driver's
internal fcport structure.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
ELS commands.
The original code would incorrectly hardcode ELS timeout values
rather than using the traditional '2 * r_a_tov' value. In some
cases, the hardcoded values would be larger than the
mailbox-command-timeout and result in a needless BIG_HAMMER (ISP
reset), the typical recovery mechanism employed in such cases.
The second defect in the original code was in the assignment of
the default 'ha->r_a_tov' to twice the traditional value.
Correct this by setting the value to 10 seconds.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There's no point in hitting the RISC with what will most
assuredly be an unsucessful reset of the RISC hardware if the
initial stop-firmware mailbox command fails with a time-out
status. Instead, to avoid what could amount to a lengthy
stop-firmware/detect-failure/reset-risc loop, continue with
driver unloading and discard the stop-firmware requirement.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Collapse duplicate codes called during probe() and RISC-reset
into qla2x00_setup_chip().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
To insure that there is no stale data present during EFT
re-registration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Refactor SRB-failure completion codes in the process. Also,
signal the DPC routine to complete sooner as backend processing
at shutdown-time is superflous.
[jejb: resolve conflicts with pci_enable_device_bars removal]
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There is a case where 54xx HBA loads MID firmware as it use 24xx
firmware. In this case, the driver should issue
MBC_MID_INITIALIZE FIRMWARE even though the HBA doesn't support
NPIV. This patch make changes in the driver so that could behave
accordingly.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Original code would clear the buffer after the firmware had
already been initialized to use the buffer, thus potentially
and inadvertantly clearing data previously DMA'd by the
firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
FCE support enables the firmware to record FC extended link
services and basic link services frames which have been
transmitted and received by the ISP. This allows for a limited
view of the FC traffic through the ISP without using a FC
analyzer. This can be useful in situations where a physical
connection to the FC bus is not possible.
The driver exports this information in two ways -- first, via a
debugfs node exported for all supported ISPs under:
<debugfs_mount_point>/qla2xxx/qla2xxx_<host_no>/fce
where a read of the 'fce' file will provide a snapshot of the
firmware's FCE buffer; and finally, the FCE buffer will be
extracted during a firmware-dump scenario.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
In preparation for FCE (Fibre Channel Event) tracing support.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Firmware will export to software the maximum number of vports
supported for any given firmware version and ISP type. Use this
information rather than the current hardcoding of limitations
within the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Do not adjust the iIDMA speed on ports which have a faster
link-speed than the HBA itself.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In NCR_D700, a4000t, aic7xxx_old, bvme6000, dpt_i2o, gdth, lpfc,
megaraid, mvme16x osst, pluto, qla2xxx, zorro7xx
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Original implementation manipulated the FC_GS values for
port-speed. Transition the codes to use the driver's own
internal representations as this makes for a reduction in
duplicate 'conversion' codes throughout the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This is a patch to fix 'segmentation fault' issue which was initiated
by Richard Lary <rlary@us.ibm.com>. Thanks again Richard.
- on following sysfs attritute function, changes have made so that both
count and offset input parameters are honored by the functions.
= qla2x00_sysfs_read_nvram()
= qla2x00_sysfs_read_vpd()
- made changes so that NVRAM data to be cached to minimize H/W accesses
during agent querying of the driver's.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Large code-reuse from ISP24xx, consolidate RISC memory
extraction routines during firmware-dump.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
As the "must-check" return-value of pci_set_msi() is never
really checked.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Original from Peter Oruba <peter.oruba@amd.com>. Additional
cleanups included.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
|
|
Following patch adds support for NPIV (N-Port ID Virtualization) to the
qla2xxx.
- supported within switched-fabric topologies only.
- supports up to 63 virtual ports on each physical port.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Optimize fault kprobe handling just like powerpc.
[SPARC]: Wire up utimensat syscall.
[SPARC64]: Fix request_irq() ignored result warnings in PCI controller code.
[SPARC64]: Kill asm-sparc64/pbm.h
[ATYFB]: Fix sparc includes.
[QLA2XXX]: Fix build on sparc.
[SPARC64]: Removal of trivial pci_controller_info uses.
[SPARC64]: Move index info pci_pbm_info.
[SPARC64]: Move {setup,teardown}_msi_irq into pci_pbm_info.
[SPARC64]: Move pci_ops into pci_pbm_info.
[SPARC64] SBUS: Error interrupt registry cleanups.
[SPARC64] PCI: Use root list of pbm's instead of pci_controller_info's
[SPARC64] PCI: Kill PROM_PCIRNG_MAX and PROM_PCIIMAP_MAX.
[SPARC64] PCI: Use common routine to fetch PBM properties.
|
|
We now use pci_device_to_OF_node() to get properties
and of_get_property() returns const pointers.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
executed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Some sparc64 boxes don't have a valid NVRAM (from which the driver
takes its WWPN) try to extract this from open firmware instead and if
that fails, fall back to a default, which would be invalid if more
than one machine on the same SAN does this, since two machines with
the same WWPN would be illegal, so warn when taking this potentially
invalid default.
Tested on SunBlade-1000:
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
|
