| Age | Commit message (Collapse) | Author |
|---|
|
Swing/emphasis settings in NVRAM were not being honoured due
to the driver not converting the serial-link options from LE
to host-endian format.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
loop-resync.
If the Get Port Database call fails during local-loop
update, then schedule the DPC routine to perform a rescan as
the firmware would have updated the Get ID List port-entries
of their new state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Small changes to register retrieval and order as per latest
firmware specification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Driver would not correctly re-enable the write-protection
bits of the flash part after updates.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Problem report (against 2.4.x driver) from Jeff Layton
<jlayton@redhat.com>:
An OEM noticed that the U6 qla2200 driver would hang for
around 2 minutes at boot time and then proceed normally. I
found that the delay was occurring when loading the new
firmware into the card, and was due to a
schedule_timeout(10) added to the bottom of the polling
loop.
Some testing showed that the load ram operation on the card
was very quick (on the order of a couple of jiffies), but
the sleep in the polling loop was making each operation take
around 25-30.
The attached patch corrects this by making it skip sleeping
during the load ram operation, since I believe we only do
that when the module is plugged in. It also skips sleeping
if the mbox_int flag got set during the current loop.
This corrected the hang on my test setup, and OEM also
confirmed that it corrected the problem for them.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Mailbox commands are polled for completion during ISP
initialization. During potentially 'long' mailbox commands
(i.e. fabric login), we really don't want a busy-wait delay
to potentially trigger a (benign) soft-lockup BUG().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
There's no point in displaying the message during a valid
underrun case. Limit the message to potentially problematic
cases.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The initial-control-block references are not always correct
as the use-node-name qualifier during NVRAM configuration
will cause the firmware to use the portname as a base for
the nodename.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Original From: Adrian Bunk
Here's a composite patch with Adrian's original additions and
help-text with the new Kconfig variable SCSI_QLA_FC.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Transition driver to exclusively use the request_firmware()
interfaces to retrieve firmware-blobs from user-space. This
will be the default behaviour going forward until the
embedded firmware-binary images are removed from the
upstream kernel.
Upon request, the driver caches the firmware image until the
driver is unloaded.
NOTE: The option is present to allow the user to continue to
use the firmware-loader modules, but, should be considered
deprecated.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Properly check FC_RESID for any non-transfered bytes
regardless of firmware completion status.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
A regression in a recent change
33135aa2a568ec1a30e734f18e5315e10516e4f3 caused the driver
to mistakenly drop handling of AENs. Due to the incorrect
handling, ports would not reappear after RSCNs and LIPs.
Drops unused/incorrect compound #define from qla_def.h.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated. A
similar delay was needed with earlier ISPs.
Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Correct issue where abort I/O command was not being issued
when the loop-state was down.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
When mulitple initiators are coming up in an FCAL topology.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
On MMIO relaxed-order platforms, it is possible for the
proper delay during NVRAM access to begin before the request
passes through the PCI bus (via a MMIO write) to the ISP.
Thus, causing a subsequent read to the NVRAM part to fail.
Add a MMIO read, after the MMIO write to insure any posted
writes are flushed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This is the drivers/scsi/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The label eh_dev_reset_done is still in use
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
From: 'Andrew Vasquez' <andrew.vasquez@qlogic.com>
Drop scsi_populate_tag_msg() interrogation.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The file is missing an include of scsi_transport_fc.h
drivers/scsi/qla2xxx/qla_rscn.c:334: error: implicit declaration of function 'fc_remote_port_unblock'
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Here's a patch which drops the eh_active checks in the qla2xxx
eh_handler callbacks.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
While populating command type 6 and 7 IOCBs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
ISP23xx and ISP24xx chips have support for an adaptive
method of posting SCSI command completions for multiple SCSI
commands during a single system interrupt.
SCSI commands are placed on the system response queue
without interrupting the host until 1) a delay timer
expires; or 2) a SCSI command completes with an error.
As long as the host software (qla2xxx) services the response
queue for completions (this polling is done during
queuecommand()) within the 'delay timer' period, the
firmware will not generate system interrupt.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The non-handled failure cases of the Fabric Login mailbox
command handling logic would incorrectly mark the fcport as
dead and not allow the standard port-down-retry-count logic
to manage the transition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If qla2x00_probe_one()'s call to qla2x00_iospace_config() fails, we call
qla2x00_free_device() to clean up. But because ha->dpc_pid hasn't been set
yet, qla2x00_free_device() tries to stop a kernel thread which hasn't started
yet. It does wait_for_completion() against an uninitialised completion struct
and the kernel hangs up.
Fix it by initialising ha->dpc_pid a bit earlier.
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch fixes a hole in the rport unblock handling when processing
fabric events via the ADISC/PLOGI device state machine. Original code
would not properly 'unblock' the port upon the port reloging into the
fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
On ISP24xx parts, stop execution of firmware during ISP
tear-down.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
From: Nishanth Aravamudan <nacc@us.ibm.com>
Replace schedule_timeout() with
msleep()/msleep_interruptible() as appropriate, to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
fc_remove_host() should only be called after a scsi_host has
been successfully added via scsi_add_host() -- any failures
while qla2xxx probing would result in an incorrect call to
fc_remove_host() during cleanup.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Export additional host information via the shost_attrs member in
the scsi_host template. Attributes include: driver version,
firmware version, ISP serial number, ISP type, ISP product ID,
HBA model name, HBA model description, PCI interconnect
information, and HBA port state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In a corner-case failure where the request-q does not
contain enough entries for a given request, pci_unmap_sg()
would be called twice. Remove direct call and let the
failure-path logic handle the unmapping.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Remove unnecessary RISC pause/release barriers during
ISP24xx flash manipulation. The ISP24xx can arbitrate flash
access requests during RISC executions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Original implementation used an overloaded bit in the EFI
parameters. The correct bit is BIT_4 of the special_options
section of NVRAM.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
