aboutsummaryrefslogtreecommitdiff
path: root/drivers/scsi/scsi_error.c
AgeCommit message (Collapse)Author
2008-12-01[SCSI] make scsi_eh_try_stu use block timeoutJames Bottomley
scsi_eh_try_stu() was still using the timeout parameter in the device which is now not set (i.e. zero filled) meaning that it waited no time at all for the start unit command to complete (leading the routine to conclude failure every time). This lead to a 2.6.27 regression: http://bugzilla.kernel.org/show_bug.cgi?id=12120 Where firewire devices that were non spec compliant wouldn't spin up. Fix this by using the block queue timeout value instead. Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-11-05[SCSI] scsi_error regression: Fix idempotent command handlingMike Christie
Drivers want to be able to return DID_TRANSPORT_DISRUPTED and have it do the right thing for commands like tape and passthrouh as far as retries go. The LLDs previously used DID_BUS_BUSY or DID_ERROR which followed the cmd->retries limit, but DID_TRANSPORT_DISRUPTED was skipping that check so it could have caused a problem with tape commands. This patch has DID_TRANSPORT_DISRUPTED check the cmd->retries/cmd->allowed. Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-10-13[SCSI] scsi_error: fix target reset handlingJames Bottomley
There's a target reset bug. This loop: for (id = 0; id <= shost->max_id; id++) { Never terminates if shost->max_id is set to ~0, like aic94xx does. It's also pretty inefficient since you mostly have compact target numbers, but the max_id can be very high. The best way would be to sort the recovery list by target id and skip them if they're equal, but even a worst case O(N^2) traversal is probably OK here, so fix it by finding the next highest target number (assuming n+1) and terminating when there isn't one. Cc: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-10-13[SCSI] modify scsi to handle new fail fast flags.Mike Christie
This checks the errors the scsi-ml determined were retryable and returns if we should fast fail it based on the request fail fast flags. Without the patch, drivers like lpfc, qla2xxx and fcoe would return DID_ERROR for what it determines is a temporary communication problem. There is no loss of connectivity at that time and the driver thinks that it would be fast to retry at the driver level. SCSI-ml will however sees fast fail on the request and DID_ERROR and will fast fail the io. This will then cause dm-multipath to fail the path and possibley switch target controllers when we should be retrying at the scsi layer. We also were fast failing device errors to dm multiapth when unless the scsi_dh modules think otherwis we want to retry at the scsi layer because multipath can only retry the IO like scsi should have done. multipath is a little dumber though because it does not what the error was for and assumes that it should fail the paths. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-10-13[SCSI] scsi: add transport host byte errors (v3)Mike Christie
Currently, if there is a transport problem the iscsi drivers will return outstanding commands (commands being exeucted by the driver/fw/hw) with DID_BUS_BUSY and block the session so no new commands can be queued. Commands that are caught between the failure handling and blocking are failed with DID_IMM_RETRY or one of the scsi ml queuecommand return values. When the recovery_timeout fires, the iscsi drivers then fail IO with DID_NO_CONNECT. For fcp, some drivers will fail some outstanding IO (disk but possibly not tape) with DID_BUS_BUSY or DID_ERROR or some other value that causes a retry and hits the scsi_error.c failfast check, block the rport, and commands caught in the race are failed with DID_IMM_RETRY. Other drivers, may hold onto all IO and wait for the terminate_rport_io or dev_loss_tmo_callbk to be called. The following patches attempt to unify what upper layers will see drivers like multipath can make a good guess. This relies on drivers being hooked into their transport class. This first patch just defines two new host byte errors so drivers can return the same value for when a rport/session is blocked and for when the fast_io_fail_tmo fires. The idea is that if the LLD/class detects a problem and is going to block a rport/session, then if the LLD wants or must return the command to scsi-ml, then it can return it with DID_TRANSPORT_DISRUPTED. This will requeue the IO into the same scsi queue it came from, until the fast io fail timer fires and the class decides what to do. When using multipath and the fast_io_fail_tmo fires then the class can fail commands with DID_TRANSPORT_FAILFAST or drivers can use DID_TRANSPORT_FAILFAST in their terminate_rport_io callbacks or the equivlent in iscsi if we ever implement more advanced recovery methods. A LLD, like lpfc, could continue to return DID_ERROR and then it will hit the normal failfast path, so drivers do not have fully be ported to work better. The point of the patches is that upper layers will not see a failure that could be recovered from while the rport/session is blocked until fast_io_fail_tmo/recovery_timeout fires. V3 Remove some comments. V2 Fixed patch/diff errors and renamed DID_TRANSPORT_BLOCKED to DID_TRANSPORT_DISRUPTED. V1 initial patch. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-10-09block: unify request timeout handlingJens Axboe
Right now SCSI and others do their own command timeout handling. Move those bits to the block layer. Instead of having a timer per command, we try to be a bit more clever and simply have one per-queue. This avoids the overhead of having to tear down and setup a timer for each command, so it will result in a lot less timer fiddling. Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-08-29[SCSI] make scsi_check_sense HARDWARE_ERROR return ADD_TO_MLQUEUE on retryMike Anderson
Change scsi_check_sense HARDWARE_ERROR check to return ADD_TO_MLQUEUE if device->retry_hwerror is set to allow retries to occur without restriction of blk_noretry_request check. Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-27[SCSI] replace __FUNCTION__ with __func__Harvey Harrison
[jejb: fixed up a ton of missed conversions. All of you are on notice this has happened, driver trees will now need to be rebased] Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: SCSI List <linux-scsi@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-26[SCSI] scsi_eh_prep_cmnd should save scmd->underflowAlan Stern
This patch (as1116) fixes a bug in scsi_eh_prep_cmnd() and scsi_eh_restore_cmnd(). These routines are supposed to save any values they change and restore them later, but someone forgot to save & restore scmd->underflow. This fixes part of the problem reported in Bugzilla #9638. [jejb: fix up rejections around DIF/DIX] Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-26[SCSI] Do not retry a request whose data integrity check failedMartin K. Petersen
If initiator or target reject the I/O due to DIF errors there is no point in retrying. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-26[SCSI] Command protection operationMartin K. Petersen
Controllers that support DMA of protection information must be told explicitly how to handle the I/O. The controller has no knowledge of the protection capabilities of the target device so this information must be passed in the scsi_cmnd. - The protection operation tells the HBA whether to generate, strip or verify protection information. - The protection type tells the HBA which layout the target is formatted with. This is necessary because the controller must be able to correctly interpret the included protection information in order to verify it. - When a scsi_cmnd is reused for error handling the protection operation must be cleared and saved while error handling is in progress. - prot_op and prot_type are placed in an existing hole in scsi_cmnd and don't cause the structure to grow. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-06-05[SCSI] scsi_dh: add infrastructure for SCSI Device HandlersChandra Seetharaman
Some of the storage devices (that can be accessed through multiple paths), do need some special handling for 1. Activating the passive path of the storage access. 2. Decode and handle the special sense codes returned by the devices. 3. Handle the I/Os being sent to the passive path, especially during the device probe time. when accessed through multiple paths. As of today this special device handling is done at the dm-multipath layer using dm-handlers. That works well for (1); for (2) to be handled at dm layer, scsi sense information need to be exported from SCSI to dm-layer, which is not very attractive; (3) cannot be done at all at the dm layer. Device handler has been moved to SCSI mainly to handle (2) and (3) properly. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-05-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: [SCSI] aic94xx: fix section mismatch [SCSI] u14-34f: Fix 32bit only problem [SCSI] dpt_i2o: sysfs code [SCSI] dpt_i2o: 64 bit support [SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt to dma_alloc_coherent [SCSI] dpt_i2o: use standard __init / __exit code [SCSI] megaraid_sas: fix suspend/resume sections [SCSI] aacraid: Add Power Management support [SCSI] aacraid: Fix jbod operations scan issues [SCSI] aacraid: Fix warning about macro side-effects [SCSI] add support for variable length extended commands [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer [SCSI] bsg: add large command support [SCSI] aacraid: Fix down_interruptible() to check the return value correctly [SCSI] megaraid_sas; Update the Version and Changelog [SCSI] ibmvscsi: Handle non SCSI error status [SCSI] bug fix for free list handling [SCSI] ipr: Rename ipr's state scsi host attribute to prevent collisions [SCSI] megaraid_mbox: fix Dell CERC firmware problem
2008-05-02[SCSI] Let scsi_cmnd->cmnd use request->cmd bufferBoaz Harrosh
- struct scsi_cmnd had a 16 bytes command buffer of its own. This is an unnecessary duplication and copy of request's cmd. It is probably left overs from the time that scsi_cmnd could function without a request attached. So clean that up. - Once above is done, few places, apart from scsi-ml, needed adjustments due to changing the data type of scsi_cmnd->cmnd. - Lots of drivers still use MAX_COMMAND_SIZE. So I have left that #define but equate it to BLK_MAX_CDB. The way I see it and is reflected in the patch below is. MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB as per the SCSI standard and is not related to the implementation. BLK_MAX_CDB. - The allocated space at the request level - I have audit all ISA drivers and made sure none use ->cmnd in a DMA Operation. Same audit was done by Andi Kleen. (*)fixed-length here means commands that their size can be determined by their opcode and the CDB does not carry a length specifier, (unlike the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly true and the SCSI standard also defines extended commands and vendor specific commands that can be bigger than 16 bytes. The kernel will support these using the same infrastructure used for VARLEN CDB's. So in effect MAX_COMMAND_SIZE means the maximum size command scsi-ml supports without specifying a cmd_len by ULD's Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-29block: use blk_rq_init() to initialize the requestFUJITA Tomonori
Any path needs to call it to initialize the request. This is a preparation for large command support, which needs to initialize the request in a proper way (that is, just doing a memset() will not work). Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-04-07[SCSI] add scsi_build_sense_buffer helper functionFUJITA Tomonori
This adds scsi_build_sense_buffer, a simple helper function to build sense data in a buffer. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-07[SCSI] scsi_error: add target reset handlerMike Christie
The problem is that serveral drivers are sending a target reset from the device reset handler, and if we have multiple devices a target reset gets sent for each device when only one would be sufficient. And if we do a target reset it affects all the commands on the target so the device reset handler code only cleaning up one devices's commands makes programming the driver a little more difficult than it should be. This patch adds a target reset handler, which drivers can use to send a target reset. If successful it cleans up the commands for a devices accessed through that starget. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-30[SCSI] bidirectional command supportBoaz Harrosh
At the block level bidi request uses req->next_rq pointer for a second bidi_read request. At Scsi-midlayer a second scsi_data_buffer structure is used for the bidi_read part. This bidi scsi_data_buffer is put on request->next_rq->special. Struct scsi_cmnd is not changed. - Define scsi_bidi_cmnd() to return true if it is a bidi request and a second sgtable was allocated. - Define scsi_in()/scsi_out() to return the in or out scsi_data_buffer from this command This API is to isolate users from the mechanics of bidi. - Define scsi_end_bidi_request() to do what scsi_end_request() does but for a bidi request. This is necessary because bidi commands are a bit tricky here. (See comments in body) - scsi_release_buffers() will also release the bidi_read scsi_data_buffer - scsi_io_completion() on bidi commands will now call scsi_end_bidi_request() and return. - The previous work done in scsi_init_io() is now done in a new scsi_init_sgtable() (which is 99% identical to old scsi_init_io()) The new scsi_init_io() will call the above twice if needed also for the bidi_read command. Only at this point is a command bidi. - In scsi_error.c at scsi_eh_prep/restore_cmnd() make sure bidi-lld is not confused by a get-sense command that looks like bidi. This is done by puting NULL at request->next_rq, and restoring. [jejb: update to sg_table and resolve conflicts also update to blk-end-request and resolve conflicts] Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-30[SCSI] implement scsi_data_bufferBoaz Harrosh
In preparation for bidi we abstract all IO members of scsi_cmnd, that will need to duplicate, into a substructure. - Group all IO members of scsi_cmnd into a scsi_data_buffer structure. - Adjust accessors to new members. - scsi_{alloc,free}_sgtable receive a scsi_data_buffer instead of scsi_cmnd. And work on it. - Adjust scsi_init_io() and scsi_release_buffers() for above change. - Fix other parts of scsi_lib/scsi.c to members migration. Use accessors where appropriate. - fix Documentation about scsi_cmnd in scsi_host.h - scsi_error.c * Changed needed members of struct scsi_eh_save. * Careful considerations in scsi_eh_prep/restore_cmnd. - sd.c and sr.c * sd and sr would adjust IO size to align on device's block size so code needs to change once we move to scsi_data_buff implementation. * Convert code to use scsi_for_each_sg * Use data accessors where appropriate. - tgt: convert libsrp to use scsi_data_buffer - isd200: This driver still bangs on scsi_cmnd IO members, so need changing [jejb: rebased on top of sg_table patches fixed up conflicts and used the synergy to eliminate use_sg and sg_count] Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-23[SCSI] replace sizeof sense_buffer with SCSI_SENSE_BUFFERSIZEFUJITA Tomonori
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in several LLDs. It's a preparation for the future changes to remove sense_buffer array in scsi_cmnd structure. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11[SCSI] docbook and kernel-doc updatesRandy Dunlap
- Change title to remove "Mid-Layer" since the doc is about all of the SCSI layers. - Use "SCSI" instead of "scsi" in docbook text. - Use "*/" to end kernel-doc notation blocks. - A few other minor typo fixes. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11[SCSI] Add Documentation and integrate into docbook buildRob Landley
Add Documentation/DocBook/scsi_midlayer.tmpl, add to Makefile, and update lots of kerneldoc comments in drivers/scsi/*. Updated with comments from Stefan Richter, Stephen M. Cameron, James Bottomley and Randy Dunlap. Signed-off-by: Rob Landley <rob@landley.net> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-06Revert "scsi: revert "[SCSI] Get rid of scsi_cmnd->done""Linus Torvalds
This reverts commit ac40532ef0b8649e6f7f83859ea0de1c4ed08a19, which gets us back the original cleanup of 6f5391c283d7fdcf24bf40786ea79061919d1e1d. It turns out that the bug that was triggered by that commit was apparently not actually triggered by that commit at all, and just the testing conditions had changed enough to make it appear to be due to it. The real problem seems to have been found by Peter Osterlund: "pktcdvd sets it [block device size] when opening the /dev/pktcdvd device, but when the drive is later opened as /dev/scd0, there is nothing that sets it back. (Btw, 40944 is possible if the disk is a CDRW that was formatted with "cdrwtool -m 10236".) The problem is that pktcdvd opens the cd device in non-blocking mode when pktsetup is run, and doesn't close it again until pktsetup -d is run. The effect is that if you meanwhile open the cd device, blkdev.c:do_open() doesn't call bd_set_size() because bdev->bd_openers is non-zero." In particular, to repeat the bug (regardless of whether commit 6f5391c283d7fdcf24bf40786ea79061919d1e1d is applied or not): " 1. Start with an empty drive. 2. pktsetup 0 /dev/scd0 3. Insert a CD containing an isofs filesystem. 4. mount /dev/pktcdvd/0 /mnt/tmp 5. umount /mnt/tmp 6. Press the eject button. 7. Insert a DVD containing a non-writable filesystem. 8. mount /dev/scd0 /mnt/tmp 9. find /mnt/tmp -type f -print0 | xargs -0 sha1sum >/dev/null 10. If the DVD contains data beyond the physical size of a CD, you get I/O errors in the terminal, and dmesg reports lots of "attempt to access beyond end of device" errors." which in turn is because the nested open after the media change won't cause the size to be set properly (because the original open still holds the block device, and we only do the bd_set_size() when we don't have other people holding the device open). The proper fix for that is probably to just do something like bdev->bd_inode->i_size = (loff_t)get_capacity(disk)<<9; in fs/block_dev.c:do_open() even for the cases where we're not the original opener (but *not* call bd_set_size(), since that will also change the block size of the device). Cc: Peter Osterlund <petero2@telia.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-02scsi: revert "[SCSI] Get rid of scsi_cmnd->done"Ingo Molnar
This reverts commit 6f5391c283d7fdcf24bf40786ea79061919d1e1d ("[SCSI] Get rid of scsi_cmnd->done") that was supposed to be a cleanup commit, but apparently it causes regressions: Bug 9370 - v2.6.24-rc2-409-g9418d5d: attempt to access beyond end of device http://bugzilla.kernel.org/show_bug.cgi?id=9370 this patch should be reintroduced in a more split-up form to make testing of it easier. Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Matthew Wilcox <matthew@wil.cx> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-17[SCSI] include linux/scatterlist.h in scsi_eh.hJames Bottomley
Spotted by Paul Jackson <pj@sgi.com> The error handler rework moved the scatterlist into a globally exposed structure in scsi_eh.h; unfortunately, the scatterlist include needs to move from scsi_error.c to scsi_eh.h to allow this to compile universally. Acked-by: Paul Jackson <pj@sgi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12[SCSI] scsi_error: Refactoring scsi_error to facilitate in synchronous ↵Boaz Harrosh
REQUEST_SENSE - Drivers/transports that want to send a synchronous REQUEST_SENSE command as part of their .queuecommand sequence, have 2 new API's that facilitate in doing so and abstract them from scsi-ml internals. void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *sesci, unsigned char *cmnd, int cmnd_size, int sense_bytes) Will hijack a command and prepare it for request sense if needed. And will save any later needed info into a scsi_eh_save structure. void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *sesci); Will undo any changes done to a command by above function. Making it ready for completion. - Re-factor scsi_send_eh_cmnd() to use above APIs Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12[SCSI] scsi_error: code cleanup before refactoring of scsi_send_eh_cmnd()Boaz Harrosh
- regrouped variables for easier reviewing of next patch - Support of cmnd==NULL in call to scsi_send_eh_cmnd() - In the @sense_bytes case set transfer size to the minimum size of sense_buffer and passed @sense_bytes. cmnd[4] is set accordingly. - REQUEST_SENSE is set into cmnd[0] so if @sense_bytes is not Zero passed @cmnd should be NULL. - Also save/restore resid of failed command. - Adjust caller Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12[SCSI] Get rid of scsi_cmnd->doneMatthew Wilcox
The ULD ->done callback moves into the scsi_driver. By moving the call to scsi_io_completion() from scsi_blk_pc_done() to scsi_finish_command(), we can eliminate the latter entirely. By returning 'good_bytes' from the ->done callback (rather than invoking scsi_io_completion()), we can stop exporting scsi_io_completion(). Also move the prototypes from sd.h to sd.c as they're all internal anyway. Rename sd_rw_intr to sd_done and rw_intr to sr_done. Inspired-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12[SCSI] Remove ->pid field from scsi_cmndMatthew Wilcox
The pid field is a duplicate of the serial_number field and has been scheduled for removal for a long time. A few drivers were still using it, so just change them to use serial_number instead. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12[SCSI] Improve error message when offlining a deviceMatthew Wilcox
The current code prints: scsi 13:0:4:0: scsi: Device offlined - not ready after error recovery which is repetitively redundant. This patch changes that message to: scsi 6:0:6:0: Device offlined - not ready after error recovery Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12[SCSI] scsi_error.c should #include "scsi_transport_api.h"Adrian Bunk
Every file should #include the headers containing the prototypes for its global functions (in this case for scsi_schedule_eh()). Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-17Freezer: make kernel threads nonfreezable by defaultRafael J. Wysocki
Currently, the freezer treats all tasks as freezable, except for the kernel threads that explicitly set the PF_NOFREEZE flag for themselves. This approach is problematic, since it requires every kernel thread to either set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't care for the freezing of tasks at all. It seems better to only require the kernel threads that want to or need to be frozen to use some freezer-related code and to remove any freezer-related code from the other (nonfreezable) kernel threads, which is done in this patch. The patch causes all kernel threads to be nonfreezable by default (ie. to have PF_NOFREEZE set by default) and introduces the set_freezable() function that should be called by the freezable kernel threads in order to unset PF_NOFREEZE. It also makes all of the currently freezable kernel threads call set_freezable(), so it shouldn't cause any (intentional) change of behaviour to appear. Additionally, it updates documentation to describe the freezing of tasks more accurately. [akpm@linux-foundation.org: build fixes] Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net> Cc: Pavel Machek <pavel@ucw.cz> Cc: Oleg Nesterov <oleg@tv-sign.ru> Cc: Gautham R Shenoy <ego@in.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-24[SCSI] scsi_error: send the sense buffer down without copyingJames Bottomley
Now that the block submission path correctly bounces, we can simply use the command sense_buffer to send to retrieve sense information and junk the unnecessary page allocation. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-06[SCSI] use sysfs configured timeout for EH Start Unit timeoutBrian King
Use the sysfs configurable timeout when issuing a START_UNIT command from the scsi error handler. This is needed for devices which take longer than thirty seconds to respond to the start unit. The problem was observed when sending a start unit to a disk array device in an ipr RAID adapter, which results in the adapter firmware sending potentially multiple commands to physical devices as a result of this command, which ended up timing out sometimes. This patch does not change the default value used for this command. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-05Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (87 commits) [SCSI] fusion: fix domain validation loops [SCSI] qla2xxx: fix regression on sparc64 [SCSI] modalias for scsi devices [SCSI] sg: cap reserved_size values at max_sectors [SCSI] BusLogic: stop using check_region [SCSI] tgt: fix rdma transfer bugs [SCSI] aacraid: fix aacraid not finding device [SCSI] aacraid: Correct SMC products in aacraid.txt [SCSI] scsi_error.c: Add EH Start Unit retry [SCSI] aacraid: [Fastboot] Panics for AACRAID driver during 'insmod' for kexec test. [SCSI] ipr: Driver version to 2.3.2 [SCSI] ipr: Faster sg list fetch [SCSI] ipr: Return better qc_issue errors [SCSI] ipr: Disrupt device error [SCSI] ipr: Improve async error logging level control [SCSI] ipr: PCI unblock config access fix [SCSI] ipr: Fix for oops following SATA request sense [SCSI] ipr: Log error for SAS dual path switch [SCSI] ipr: Enable logging of debug error data for all devices [SCSI] ipr: Add new PCI-E IDs to device table ...
2007-04-17[SCSI] scsi_error.c: Add EH Start Unit retryBrian King
Currently, the scsi error handler will issue a START_UNIT command if the drive indicates it needs its motor started and the allow_restart flag is set in the scsi_device. If, after the scsi error handler invokes a host adapter reset due to error recovery, a device is in a unit attention state AND also needs a START_UNIT, that device will be placed offline. The disk array devices on an ipr RAID adapter will do exactly this when in a dual initiator configuration. This patch adds a single retry to the EH initiated START_UNIT. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Patch modified and Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-04-02[SCSI]: Fix scsi_send_eh_cmnd scatterlist handlingDavid S. Miller
This fixes a regression caused by commit: 2dc611de5a3fd955cd0298c50691d4c05046db97 The sense buffer code in scsi_send_eh_cmnd was changed to use alloc_page() and a scatter list, but the sense data copy was not updated to match so what we actually get in the sense buffer is total grabage starting with the kernel address of the struct page we got. Basically the stack frame of scsi_send_eh_cmd() is what ends up in the sense buffer. Depending upon how pointers look on a given platform, you can end up getting sr_ioctl.c errors when you mount a cdrom. If the CDROM gives a check condition for GPCMD_GET_CONFIGURATION issued by drivers/cdrom/cdrom.c:cdrom_mmc_profile(), sr_ioctl will spit out this error message in sr_do_ioctl() with the way pointers are on sparc64: default: printk(KERN_ERR "%s: CDROM (ioctl) error, command: ", cd->cdi.name); __scsi_print_command(cgc->cmd); scsi_print_sense_hdr("sr", &sshdr); err = -EIO; This is the error Tom Callaway reported in: http://marc.info/?l=linux-sparc&m=117407453208101&w=2 Anyways, fix this by using page_address(sgl.page) which is OK because we know this is low-mem due to GFP_ATOMIC. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Christoph Hellwig <hch@lst.de>
2007-03-20[SCSI] expose eh_timed_out to the host templateJames Bottomley
It looks like megaraid_sas at least needs this to throttle its commands as they begin to time out. The code keeps the existing transport template use of eh_timed_out (and allows the transport to override the host if they both have this callback). Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-02-03[SCSI] scsi_error: Fix lost EH commandsBrian King
If an EH command times out today, the LLDD's abort handler will be called to abort the command. It is assumed that this completes successfully, which can result in the command getting completed later resulting in an oops. Improve the current implementation by escalating all the way to host reset if necessary in order to clean up the EH command. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-31[SCSI] Fix sense key MEDIUM ERROR processing and retryLuben Tuikov
1) If the device reports an uncorrectable MEDIUM ERROR, such as SK MEDIUM ERROR, ASC UNRECOVERED READ ERR, AMNF DATA FIELD or RECORD NOT FOUND, then: In scsi_check_sense() return SUCCESS so as to not retry -- the error is uncorrectable -- this speeds up total processing time. Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Extracted the MEDIUM ERROR piece and Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-27[SCSI] scsi_error.c: Export some scsi_eh_* functionsDarrick J. Wong
Export a couple of functions from scsi_error that are needed to handle failed SCSI commands from the SAS EH. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> make exports GPL and Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-11-15[SCSI] use one-element sg list in scsi_send_eh_cmndChristoph Hellwig
scsi_send_eh_cmnd is the last user of non-sg commands currently. This patch switches it to a one-element SG list. Also updates the kerneldoc comment for scsi_send_eh_cmnd to reflect reality while we're at it. Test on my mptsas card, but this should get testing with as many drivers as possible. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-10-10[PATCH] gfp annotations: scsi_errorAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-13[PATCH] SCSI: lockdep annotation in scsi_send_eh_cmndStefan Richter
Fixup for lockdep enabled kernels: Annotate an on-stack completion. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-08-26[SCSI] fix scsi_send_eh_cmnd regressionMike Christie
The callers of scsi_send_eh_cmnd are setting the cmnd buffer, and then scsi_send_eh_cmnd is copying that updated buffer to the old_cmnd variable. Then after the command runs, we end up copying that old_cmnd var which has the new cmnd to the scsi command buffer. When this command gets recent, all types of fun things happen like getting TUR or START_STOP commands with data and scatterlists. This patch made against scsi-rc-fixes, has the callers of scsi_send_eh_cmnd pass in the command so scsi_send_eh_cmnd can do the right thing. This should go into 2.6.18 since this fixes a regression added when we removed some of the scsi_cmnd fields and replaced them with local variables. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-09[SCSI] hide EH backup data outside the scsi_cmndChristoph Hellwig
Currently struct scsi_cmnd has various fields that are used to backup original data after the corresponding fields have been overridden for EH commands. This means drivers can easily get at it and misuse it. Due to the old_ naming this doesn't happen for most of them, but two that have different names have been used wrong a lot (see previous patch). Another downside is that they unessecarily bloat the scsi_cmnd size. This patch moves them onstack in scsi_send_eh_cmnd to fix those two issues aswell as allowing future EH fixes like moving the EH command submissions to use SG lists like everything else. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-27[SCSI] Block I/O while SG reset operation in progress - the midlayer patchJames Smart
The scsi midlayer portion of the patch Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-22Merge branch 'master' into upstreamJeff Garzik
Conflicts: drivers/scsi/libata-core.c drivers/scsi/libata-scsi.c include/linux/pci_ids.h
2006-06-10[SCSI] remove RQ_SCSI_* flagsChristoph Hellwig
The RQ_SCSI_* flags are a vestiage of a long past history. The EH code still sets them but we never make use of that information. The other users is pluto.c which never had a chance to work but needs to be kept compiling to keep Davem happy, so copy over the definition there. We could probably get rid of RQ_ACTIVE/RQ_INACTIVE aswell with some work, there's only two more or less bogus looking uses in ubd and scsi. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-10[SCSI] remove scsi_request infrastructureChristoph Hellwig
With Achim patch the last user (gdth) is switched away from scsi_request so we an kill it now. Also disables some code in i2o_scsi that was broken since the sg driver stopped using scsi_requests. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>