| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
drivers/scsi/libata-core.c
drivers/scsi/libata-scsi.c
include/linux/pci_ids.h
|
|
Kconfig and Makefile for iSER.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Move various QLogic, Vitesse, and Intel storage controller PCI IDs to the
main header file.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (85 commits)
[SCSI] 53c700: remove reliance on deprecated cmnd fields
[SCSI] hptiop: don't use cmnd->bufflen
[SCSI] hptiop: HighPoint RocketRAID 3xxx controller driver
[SCSI] aacraid: small misc. cleanups
[SCSI] aacraid: Update supported product information
[SCSI] aacraid: Fix return code interpretation
[SCSI] scsi_transport_sas: fix panic in sas_free_rphy
[SCSI] remove RQ_SCSI_* flags
[SCSI] remove scsi_request infrastructure
[SCSI] mptfusion: change driver revision to 3.03.10
[SCSI] mptfc: abort of board reset leaves port dead requiring reboot
[SCSI] mptfc: fix fibre channel infinite request/response loop
[SCSI] mptfc: set fibre channel fw target missing timers to one second
[SCSI] mptfusion: move fc event/reset handling to mptfc
[SCSI] spi transport: don't allow dt to be set on SE or HVD buses
[SCSI] aic7xxx: expose the bus setting to sysfs
[SCSI] scsi: remove Documentation/scsi/cpqfc.txt
[SCSI] drivers/scsi: Use ARRAY_SIZE macro
[SCSI] Remove last page_address from dc395x.c
[SCSI] hptiop: HighPoint RocketRAID 3xxx controller driver
...
Fixed up conflicts in drivers/message/fusion/mptbase.c manually (due to
the sparc interrupt cleanups)
|
|
Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers
used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA
hardreset instead of SRST. This patch makes all the converted drivers
use the standard bmdma error handler which uses both SRST and SATA
hardreset.
All the controllers should be able to perform SRST but still needs
verification. If some of the controllers can't do SRST, it will be
very easy to spot as it will show up during boot probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert sata_via to new EH. vt6420 used ATA_FLAG_SRST while vt6421
used ATA_FLAG_SATA_RESET. This difference seems to be an accident
rather than intended. This patch makes both flavors use
ata_bmdma_error_handler() which makes use of both SRST and SATA
hardreset. This behavior change is intended and if it breaks
anything, it should be very easy to spot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
We don't need to use the heavier spin lock in the irq handler.
It's quite possible we can do this in nv_generic_interrupt() as well,
but I didn't take the time to pursue that train of thought.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add hotplug support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert to new EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
nf2/3 and ck804 have irq status register. Implement better irq
handler for those flavors of nv. This patch makes different flavors
of nv controllers use different irq handlers by using separate
port_info for each flavor.
This change also makes following EH and hotplug updates easier to
integrate.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Simplify interrupt constants and make NFORCE3 equal to NFORCE2.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
nv_host_desc and nv_host are used to discern different generations of
nv controllers. Kill those. New EH/hotplug implementation will use
standard port_info/ata_port_operations for that.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sata_nv contained hotplug code which is mainly for demonstrating how
hotplug event is handled. This patch kills the demo code in
prepration for real hotplug implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Doing a full ata_busy_sleep() seems to get suspend and resume working
fine on the Apple Mac Mini, at least.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This one's quite tricky. The 53c700 uses the now deprecated fields of
the command structure for saving the prior command when it does
autosense. To fix this, we have to add extra fields to the LUN to
accommodate a copy of the real command.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
use cmnd->request_bufflen instead.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Updates:
- don't bypass SYNCHRONIZE_CACHE command
- return SCSI_MLQUEUE_HOST_BUSY when no free request slots
- move scsi_remove_host() to the begin of hpt_remove(), or it will
not work after resources being released.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn
Spelling correction, orphaned comment removal & update branch name.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received From Mark Salyzyn
Some of the cards product names changed.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
|
|
Received from Mark Salyzyn
clear_user return is 0 for success, the code fragment is written to
assume that it is the count of the number of bytes zero'd.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This is a hold over from the end device/expander conversion. Apparently
the rphy list pointer is never initialised, so list_del() on the
uninitialised pointer can panic the system
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
For a legacy ATA controller, libata registers two separate host sets.
There was no connection between the two hosts making it impossible to
traverse all ports related to the controller. This patch adds
host_set->next which points to the second host_set and makes
ata_pci_remove_one() remove all associated host_sets.
* On device removal, all ports hanging off the device are properly
detached. Prior to this patch, ports on the first host_set weren't
detached casuing oops on driver unloading.
* On device removal, both host_sets are properly freed
This will also be used by new power management code to suspend and
resume all ports of a controller. host_set/port representation will
be improved to handle legacy controllers better and this host_set
linking will go away with it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Depending on timing, ata_scsi_dev_rescan() might encounter a device
which is enabled but not yet attached to sdev. On such cases, the
original code caused oops. This patch makes ata_scsi_dev_rescan()
rescan only device which are attached to sdevs.
While at it, properly indent leading comment and add description about
how it's synchronized with sdev attach/detach.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
SIEN on some 3112 controllers doesn't mask SATA IRQ properly. IRQ
stays asserted even after SIEN is masked and IRQ is acked. Also, even
while frozen, any SATA PHY event including hardreset raises SATA IRQ.
Clearing SError seems to be the only way to deassert SATA IRQ.
This patch makes sil_host_intr() clear SError on SATA IRQs and ignore
SATA IRQs reported while frozen so that hardreset doesn't trigger
hotplug event (which ends up hardresetting again).
In such cases, the port still gets re-frozen to minimize the danger of
screaming interrupts. This results in one nil EH repeat on
controllers with broken SIEN but other than that does no harm.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make EH exit fast if the port is being unloaded.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ATA_EH_REVALIDATE should be cleared after all devices on the target
port have been revalidated. Fix ata_eh_revalidate_and_attach()
accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add RETURNS comment above ata_exec_internal() and kill extra blank
line.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Short-circuit interrupt handling if BMDMA2 is reported as 0xffffffff
indicating device removal.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch makes libata snoop 'SET FEATURES - WRITE CACHE
ENABLE/DISABLE' command, executing requisite revalidation processes
to update cached data.
Signed-off-by: Forrest Zhao <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Suggested by Jarek P.
|
|
Setup nbytes in ata_sg_init_one to the total transfer length
of the command. This is needed by some HBAs that need to know
the total transfer length of each command.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: <petkov@uni-muenster.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
With help from Tejun Heo.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Conflicts:
drivers/scsi/sata_sil24.c
|
|
Bug fix: mv_eng_timeout() calls mv_err_intr() without first grabbing the host lock,
which can lead to all sorts of interesting scenarios.
This whole error-handling portion of sata_mv is nasty (and will get fixed for
the new EH stuff), but for now this patch will help keep it on life-support.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
pdc_adma use libata-core PIO path but were left out
during ->data_xfer conversion. Initialize with proper callbacks.
This patch is against the current libata-dev#ALL. Controllers which
implement their own PIO HSM (ahci and sil24) don't need ->data_xfer, so the
above two are the only drivers which were left out during conversion.
From: "Barry K. Nathan" <barryn@pobox.com>
Signed-off-by: Barry K. Nathan <barryn@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add missing finish_wait() call after wait loop in ata_port_wait_eh().
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
The RQ_SCSI_* flags are a vestiage of a long past history. The EH code
still sets them but we never make use of that information. The other
users is pluto.c which never had a chance to work but needs to be kept
compiling to keep Davem happy, so copy over the definition there.
We could probably get rid of RQ_ACTIVE/RQ_INACTIVE aswell with some
work, there's only two more or less bogus looking uses in ubd and scsi.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
With Achim patch the last user (gdth) is switched away from scsi_request
so we an kill it now. Also disables some code in i2o_scsi that was
broken since the sg driver stopped using scsi_requests.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
|
|
This is really just a belt and braces test. The standards require
disks to respond DT not capable on a non-LVD bus ... however, not all
disks follow the standards ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Read the transciever register and display in the host transport
properties. I'm still not entirely sure what this does for multiple
transciever adapters (like some 160 ones) however, I suspect it
displays the transciever state of the switchable bus segment.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Dynamically map scattergather buffer instead of using page_address().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
HighPoint RocketRAID 3220/3320 series 8 channel PCI-X SATA RAID Host
Adapters.
Fixes from original submission:
Merge Andrew Morton's patches:
- Provide locking for global list
- Fix debug printks
- uninline function with multiple callsites
- coding style fixups
- remove unneeded casts of void*
- kfree(NULL) is legal
- Don't "succeed" if register_chrdev() failed - otherwise we'll later
unregister a not-registered chrdev.
- Don't return from hptiop_do_ioctl() with the spinlock held.
- uninline __hpt_do_ioctl()
Update for Arjan van de Ven's comments:
- put all asm/ includes after the linux/ ones
- replace mdelay with msleep
- add pci posting flush
- do not set pci command reqister in map_pci_bar
- do not try merging sg elements in hptiop_buildsgl()
- remove unused outstandingcommands member from hba structure
- remove unimplemented hptiop_abort() handler
- remove typedef u32 hpt_id_t
Other updates:
- fix endianess
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Initial pass at converting the gdth driver away from the scsi_request
interface so that the request interface can be removed post 2.6.18
without breaking gdth. Based on changes from Christoph Hellwig
<hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This removes all the leading whitespace kconfig now warns about.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
Various scsi drivers use scsi_cmnd.buffer and scsi_cmnd.bufflen in their
queuecommand functions. Those fields are internal storage for the
midlayer only and are used to restore the original payload after
request_buffer and request_bufflen have been overwritten for EH. Using
the buffer and bufflen fields means they do very broken things in error
handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
