| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We must be using the bh spin locking functions in
iscsi_eh_device_reset becuase the session lock interacts with
a thread and softirq.
This patch also fixes up a bogus comment and check in fail_command,
because no one drops the lock (bnx2i did but it is not going
upstream yet and there were other refcount changes for that).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
value
Some wires got crossed on some patches and I messed up in the code
below when rebuilding a patch. We want to be checking if flag
equaled the value indicating if we killing the session due to
final logout or if we just trying to relogin.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The segment->done functions return a iscsi error value which gives
a lot more info than conn failed, so this patch has us return
that value. I also add a new one for xmit failures.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
I had this in my patchset to add target reset support, but
it got dropped due to patching conflicts. This initial patch
just renames the function and users. We are actually just
dropping the session, and so this does not have anything to do
with the host exactly. It does for software iscsi because
we allocate a host per session, but for cxgb3i this makes no
sense.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Some endpoint code was using unsigned int and some
was using uint64_t. This converts it all to uint64_t.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
iscsi_tcp was updating the exp_statsn (exp_statsn acknowledges
status and tells the target it is ok to let the resources for
a iscsi pdu to be reused) before it got all the data for pdu read
into OS buffers. Data corruption was occuring if something happens
to a packet and the network layer requests a retransmit, and the
initiator has told the target about the udpated exp_statsn ack,
then the target may be sending data from a buffer it has reused
for a new iscsi pdu. This fixes the problem by having the LLD
(iscsi_tcp in this case) just handle the transferring of data, and
has libiscsi handle the processing of status (libiscsi completion
processing is done after LLD data transfers are complete).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
For some reason these messages ended up being printed with KERN_INFO
rendering them invisible to pretty much everyone. Switch to
KERN_NOTICE.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The old detection code couldn't handle all possible combinations of
DIX and DIF. This version does, giving priority to DIX if the
controller is capable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Now that we no longer use protection_type as trigger for preparing
protected CDBs we can remove the places that set it to zero. This
allows userland to see which protection type the device is formatted
with regardless of whether the HBA supports DIF or not.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Use the same logic to prepare RD/WRPROTECT and the protection
operation. Fixes a corner case where we could issue an unprotected
CDB and yet tell the HBA to do DIF to the drive.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There's a target reset bug.
This loop:
for (id = 0; id <= shost->max_id; id++) {
Never terminates if shost->max_id is set to ~0, like aic94xx does.
It's also pretty inefficient since you mostly have compact target
numbers, but the max_id can be very high. The best way would be to
sort the recovery list by target id and skip them if they're equal,
but even a worst case O(N^2) traversal is probably OK here, so fix it
by finding the next highest target number (assuming n+1) and
terminating when there isn't one.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
vendor events
Added support for new sysfs attributes: lpfc_stat_data_ctrl and
lpfc_max_scsicmpl_time. The attributes control statistical reporting
of io load.
Added support for new fc vendor events for error reporting.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Added new sysfs attribute lpfc_max_scsicmpl_time. Attribute, when enabled,
will control target queue depth based on I/O completion time.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Revert the target busy response in favor of the transport disrupted
response for node state transitions.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We do not need to set REQ_NOMERGE because when the module calls
blk_execute_rq -> blk_execute_rq_nowait, blk_execute_rq_nowait sets
it for us. This brings all the modules in sync for those bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add support for MSI-X Multi-Message interrupts. We use different vectors
for fast-path interrupts (i/o) and slow-patch interrupts (discovery, etc).
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
DID_TRANSPORT_DISRUPTED
[jejb: drop rejecting hunk altered by target busy patches]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add support for PCI-EEH permanent-disabling a device via lpfc_pci_remove_one()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Miscellaneous Fixes:
- Fix the wrong variable name used for checking node active usage status
- Fix numerous duplicate log message numbers
- Fix change KERN_WARNING messages to KERN_INFO.
- Stop sending erroneous LOGO to fabric after vport is already terminated
- Fix HBQ allocates that were kalloc'ing w/ GFP_KERNEL while holding a lock.
- Fix gcc 4.3.2 compiler warnings and a sparse warning
- Fix bugs in handling unsolicited ct event queue
- Reorder some of the initial link up checks, to remove odd VPI states.
- Correct poor VPI handling
- Add debug messages
- Expand Update_CFG mailbox definition
- Fix handling of VPD data offsets
- Reorder loopback flags
- convert to use offsetof()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Update driver for new SLI-3 features:
- interrupt enhancements
- lose adapter doorbell writes
- inlining support for FCP_Ixx cmds
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Miscellaneous Discovery fixes:
- Fix rejection followed by acceptance in handling RPL and RPS
unsolicited events
- Fix for vport delete crash
- Fix PLOGI vs ADISC race condition
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This checks the errors the scsi-ml determined were retryable
and returns if we should fast fail it based on the request
fail fast flags.
Without the patch, drivers like lpfc, qla2xxx and fcoe would return
DID_ERROR for what it determines is a temporary communication problem.
There is no loss of connectivity at that time and the driver thinks
that it would be fast to retry at the driver level. SCSI-ml will however
sees fast fail on the request and DID_ERROR and will fast fail the io.
This will then cause dm-multipath to fail the path and possibley switch
target controllers when we should be retrying at the scsi layer.
We also were fast failing device errors to dm multiapth when
unless the scsi_dh modules think otherwis we want to retry at
the scsi layer because multipath can only retry the IO like scsi
should have done. multipath is a little dumber though because it
does not what the error was for and assumes that it should fail
the paths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Multipath is best at handling transport errors. If it gets a device
error then there is not much the multipath layer can do. It will just
access the same device but from a different path.
This patch breaks up failfast into device, transport and driver errors.
The multipath layers (md and dm mutlipath) only ask the lower levels to
fast fail transport errors. The user of failfast, read ahead, will ask
to fast fail on all errors.
Note that blk_noretry_request will return true if any failfast bit
is set. This allows drivers that do not support the multipath failfast
bits to continue to fail on any failfast error like before. Drivers
like scsi that are able to fail fast specific errors can check
for the specific fail fast type. In the next patch I will convert
scsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This has qla2xxx use the new transport error values instead of
DID_BUS_BUSY. I am not sure if all the errors
in qla_isr.c I changed are transport related. We end up blocking/deleting
the rport for all of them so it is better to use the new transport error since
the fc classs will decide when to fail the IO.
With this patch if I pull a cable then IO that had reached
the driver, will be failed with DID_TRANSPORT_DISRUPTED (not including
tape). The fc class will then fail the IO when the fast io fail tmo
has fired, and the driver will flush any other commands running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
values
This patch converts the iscsi drivers to the new host byte values.
v2
Drop some conversions. Want to avoid conflicts with other patches.
v1
initial patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Currently, if there is a transport problem the iscsi drivers will return
outstanding commands (commands being exeucted by the driver/fw/hw) with
DID_BUS_BUSY and block the session so no new commands can be queued.
Commands that are caught between the failure handling and blocking are
failed with DID_IMM_RETRY or one of the scsi ml queuecommand return values.
When the recovery_timeout fires, the iscsi drivers then fail IO with
DID_NO_CONNECT.
For fcp, some drivers will fail some outstanding IO (disk but possibly not
tape) with DID_BUS_BUSY or DID_ERROR or some other value that causes a retry
and hits the scsi_error.c failfast check, block the rport, and commands
caught in the race are failed with DID_IMM_RETRY. Other drivers, may
hold onto all IO and wait for the terminate_rport_io or dev_loss_tmo_callbk
to be called.
The following patches attempt to unify what upper layers will see drivers
like multipath can make a good guess. This relies on drivers being
hooked into their transport class.
This first patch just defines two new host byte errors so drivers can
return the same value for when a rport/session is blocked and for
when the fast_io_fail_tmo fires.
The idea is that if the LLD/class detects a problem and is going to block
a rport/session, then if the LLD wants or must return the command to scsi-ml,
then it can return it with DID_TRANSPORT_DISRUPTED. This will requeue
the IO into the same scsi queue it came from, until the fast io fail timer
fires and the class decides what to do.
When using multipath and the fast_io_fail_tmo fires then the class
can fail commands with DID_TRANSPORT_FAILFAST or drivers can use
DID_TRANSPORT_FAILFAST in their terminate_rport_io callbacks or
the equivlent in iscsi if we ever implement more advanced recovery methods.
A LLD, like lpfc, could continue to return DID_ERROR and then it will hit
the normal failfast path, so drivers do not have fully be ported to
work better. The point of the patches is that upper layers will
not see a failure that could be recovered from while the rport/session is
blocked until fast_io_fail_tmo/recovery_timeout fires.
V3
Remove some comments.
V2
Fixed patch/diff errors and renamed DID_TRANSPORT_BLOCKED to
DID_TRANSPORT_DISRUPTED.
V1
initial patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
callbacks
The fc class now calls scsi_target_unblock after calling the
terminate callback, so this patch removes the calls from the
drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When we block a rport and the driver implements the terminate
callback we will fail IO that was running quickly. However
IO that was in the scsi_device/block queue sits there until
the dev_loss_tmo fires, and this can make it look like IO is
lost because new IO will get executed but that IO stuck in
the blocked queue sits there for some time longer.
With this patch when the fast io fail tmo fires, we will
fail the blocked IO and any new IO. This patch also allows
all drivers to partially support the fast io fail tmo. If the
terminate io callback is not implemented, we will still fail blocked
IO and any new IO, so multipath can handle that.
This patch also allows the fc and iscsi classes to implement the
same behavior. The timers are just unfornately named differently.
This patch also fixes the problem where drivers were unblocking
the target in their terminate callback, which was needed for
rport removal, but for fast io fail timeout it would cause
IO to bounce arround the scsi/block layer and the LLD queuecommand.
And it for drivers that could have IO stuck but did not have
a terminate callback the unblock calls in the class will fix
them.
v2.
- fix up bit setting style to meet JamesS's pref.
- Broke out new host byte error changes to make it easier to read.
- added JamesS's ack from list.
v1
- initial patch
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
race
We do want to call right back into the queuecommand during the race,
so we can just use SCSI_MLQUEUE_TARGET_BUSY.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
For the conditions below we do not want the queuecommand
function to call us right back, so return SCSI_MLQUEUE_TARGET_BUSY.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
rport error or race
If the fcport is not online then we do not want to block IO to all ports on
the host. We just want to stop IO on port not online, so we should be using
the SCSI_MLQUEUE_TARGET_BUSY return value.
For the case where we race with the rport memset initialization
we do not want the queuecommand to be called again so we can just use
SCSI_MLQUEUE_TARGET_BUSY for this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
session error
When qla4xxx begins recovery and the iscsi class is firing up to handle
it, we need to retrn SCSI_MLQUEUE_TARGET_BUSY from the driver instead
of host busy, because the session recovery only affects the one target.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
SCSI-ml manages the queueing limits for the device and host, but
does not do so at the target level. However something something similar
can come in userful when a driver is transitioning a transport object to
the the blocked state, becuase at that time we do not want to queue
io and we do not want the queuecommand to be called again.
The patch adds code similar to the exisiting SCSI_ML_*BUSY handlers.
You can now return SCSI_MLQUEUE_TARGET_BUSY when we hit
a transport level queueing issue like the hw cannot allocate some
resource at the iscsi session/connection level, or the target has temporarily
closed or shrunk the queueing window, or if we are transitioning
to the blocked state.
bnx2i, when they rework their firmware according to netdev
developers requests, will also need to be able to limit queueing at this
level. bnx2i will hook into libiscsi, but will allocate a scsi host per
netdevice/hba, so unlike pure software iscsi/iser which is allocating
a host per session, it cannot set the scsi_host->can_queue and return
SCSI_MLQUEUE_HOST_BUSY to reflect queueing limits on the transport.
The iscsi class/driver can also set a scsi_target->can_queue value which
reflects the max commands the driver/class can support. For iscsi this
reflects the number of commands we can support for each session due to
session/connection hw limits, driver limits, and to also reflect the
session/targets's queueing window.
Changes:
v1 - initial patch.
v2 - Fix scsi_run_queue handling of multiple blocked targets.
Previously we would break from the main loop if a device was added back on
the starved list. We now run over the list and check if any target is
blocked.
v3 - Rediff for scsi-misc.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (180 commits)
leo: disable cursor when leaving graphics mode
cg6: disable cursor when leaving graphics mode
sparc32: sun4m interrupt mask cleanup
drivers/rtc/Kconfig: don't build rtc-cmos.o on sparc32
sparc: arch/sparc/kernel/pmc.c -- extra #include?
sparc32: Add more extensive documentation of sun4m interrupts.
sparc32: Kill irq_rcvreg from sun4m_irq.c
sparc32: Delete master_l10_limit.
sparc32: Use PROM device probing for sun4c timers.
sparc32: Use PROM device probing for sun4c interrupt register.
sparc32: Delete claim_ticker14().
sparc32: Stop calling claim_ticker14() from sun4c_irq.c
sparc32: Kill clear_profile_irq btfixup entry.
sparc32: Call sun4m_clear_profile_irq() directly from sun4m_smp.c
sparc32: Remove #if 0'd code from sun4c_irq.c
sparc32: Remove some SMP ifdefs in sun4d_irq.c
sparc32: Use PROM infrastructure for probing and mapping sun4d timers.
sparc32: Use PROM device probing for sun4m irq registers.
sparc32: Use PROM device probing for sun4m timer registers.
sparc: Fix user_regset 'n' field values.
...
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
sound/core/memalloc.c
|
|
Use a special request for serialisation purposes and get rid of the
awkward ide_spin_wait_hwgroup(). This also involves converting the
ide_devset structure so it can be shared by the /proc and the ioctl code.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
[bart: use rq->cmd[] directly]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make ->io_buffers method return number of bytes transferred.
* Use ide_end_request() instead of idefloppy_end_request()
in ide_floppy_io_buffers() and then move the call out to
ide_pc_intr().
* Add ide_io_buffers() helper and convert ide-{floppy,scsi}.c
to use it instead of ide*_io_buffers().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Preparation for ide_{floppy,scsi}_io_buffers() unification.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use drive->media and drive->scsi to check if ->dsc_overlap
can be set by HDIO_SET_NICE ioctl in generic_ide_ioctl().
* Remove unused ->supports_dsc_overlap field from ide_driver_t.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add struct ide_devset, S_* flags, *DEVSET() & ide*_devset_*() macros.
* Add 'const struct ide_devset **settings' to ide_driver_t.
* Use 'const struct ide_devset **settings' in ide_drive_t instead of
'struct ide_settings_s *settings'. Then convert core code and device
drivers to use struct ide_devset and co.:
- device settings are no longer allocated dynamically for each device
but instead there is an unique struct ide_devset instance per setting
- device driver keeps the pointer to the table of pointers to its
settings in ide_driver_t.settings
- generic settings are kept in ide_generic_setting[]
- ide_proc_[un]register_driver(), ide_find_setting_by_name(),
ide_{read,write}_setting() and proc_ide_{read,write}_settings()
are updated accordingly
- ide*_add_settings() are removed
* Remove no longer used __ide_add_setting(), ide_add_setting(),
__ide_remove_setting() and auto_remove_settings().
* Remove no longer used TYPE_*, SETTING_*, ide_procset_t
and ide_settings_t.
* ->keep_settings, ->using_dma, ->unmask, ->noflush, ->dsc_overlap,
->nice1, ->addressing, ->wcache and ->nowerr ide_drive_t fields
can now be bitfield flags.
While at it:
* Rename ide_find_setting_by_name() to ide_find_setting().
* Rename write_wcache() to set_wcache().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Call ide_proc_register_driver() in ide*_setup() (just before
ide*_add_settings() call) instead of in ->probe method.
Despite being basically a preparation for /proc/ide/hd*/settings
rework this is a nice cleanup in itself.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Include <linux/ata.h> directly in <linux/ide.h>
instead of through <linux/hdreg.h>.
* Include <linux/hdreg.h> only when needed.
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove needless drive->present checks from ->probe methods
(device model takes care of that).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* ERR_STAT -> ATA_ERR
* INDEX_STAT -> ATA_IDX
* ECC_STAT -> ATA_CORR
* DRQ_STAT -> ATA_DRQ
* SEEK_STAT -> ATA_DSC
* WRERR_STAT -> ATA_DF
* READY_STAT -> ATA_DRDY
* BUSY_STAT -> ATA_BUSY
* MARK_ERR -> ATA_AMNF
* TRK0_ERR -> ATA_TRK0NF
* ABRT_ERR -> ATA_ABORTED
* MCR_ERR -> ATA_MCR
* ID_ERR -> ATA_IDNF
* MC_ERR -> ATA_MC
* ECC_ERR -> ATA_UNC
* ICRC_ERR -> ATA_ICRC
* BBD_ERR -> ATA_BBK
Also:
* ILI_ERR -> ATAPI_ILI
* EOM_ERR -> ATAPI_EOM
* LFS_ERR -> ATAPI_LFS
* CD -> ATAPI_COD
* IO -> ATAPI_IO
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use ATA_CMD_* defines instead of WIN_* ones.
While at it:
* EXABYTE_ENABLE_NEXT -> ATA_EXABYTE_ENABLE_NEST
* SETFEATURES_{EN,DIS}_WCACHE -> SETFEATURES_WC_{ON,OFF}
* SETFEATURES_{EN,DIS}_AAM -> SETFEATURES_AAM_{ON,OFF}
* SMART_* -> ATA_SMART_*
* Remove stale comment from ide-proc.c.
Partially based on earlier work by Chris Wedgwood.
Acked-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
