aboutsummaryrefslogtreecommitdiff
path: root/drivers/serial
AgeCommit message (Collapse)Author
2007-05-17NS16550A: Restore HS settings in EXCR2 on resumeDavid Woodhouse
After a suspend/resume cycle, the UART may have been reset into low-speed mode -- either because it's actually been reset, or because the firmware pokes at the old-style divisor registers. If we detected it as a NS16550A SuperIO chip in the first place and set baud_base to 921600, then we should do so again in the resume path. This patch adds that code to serial8250_resume_port(), and also makes serial8250_resume() actually call serial8250_resume_port() for each port instead of just calling uart_resume_port() directly. And thus fixes serial port operation after suspend/resume. It also fixes a bogus comment where we write the EXCR2 register with a comment saying /* EXCR1 */ Signed-off-by: David Woodhouse <dwmw2@infradead.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17icom: add new sub-device-id to support new adapterwendy xiong
This patch add new sub-device-id to support new adapter and changed the interrupt irq number for unsigned char to unsigned int. [akpm@osdl.org: fix whitespace in device table] Signed-off by: Wendy Xiong <wendyx@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15[SPARC64]: Add hypervisor API negotiation and fix console bugs.David S. Miller
Hypervisor interfaces need to be negotiated in order to use some API calls reliably. So add a small set of interfaces to request API versions and query current settings. This allows us to fix some bugs in the hypervisor console: 1) If we can negotiate API group CORE of at least major 1 minor 1 we can use con_read and con_write which can improve console performance quite a bit. 2) When we do a console write request, we should hold the spinlock around the whole request, not a byte at a time. What would happen is that it's easy for output from different cpus to get mixed with each other. 3) Use consistent udelay() based polling, udelay(1) each loop with a limit of 1000 polls to handle stuck hypervisor console. Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-13[SERIAL] SUNHV: Add an ID string.David S. Miller
The 'compatible' property can be SUNW,sun4v-console as well as 'qcn'. Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-11[ARM] 4332/2: KS8695: Serial driverAndrew Victor
A driver for the KS8695 internal UART. Based on the 2.6.9 driver from Micrel. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-11[ARM] ecard: add ecardm_iomap() / ecardm_iounmap()Russell King
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion cards. Convert all expansion card drivers to use them. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-10Merge branch 'master' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (24 commits) [POWERPC] Fix compile error with kexec and CONFIG_SMP=n [POWERPC] Split initrd logic out of early_init_dt_scan_chosen() to fix warning [POWERPC] Fix warning in hpte_decode(), and generalize it [POWERPC] Minor pSeries IOMMU debug cleanup [POWERPC] PS3: Fix sys manager build error [POWERPC] Assorted janitorial EEH cleanups [POWERPC] We don't define CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID [POWERPC] pmu_sys_suspended is only defined for PPC32 [POWERPC] Fix incorrect calculation of I/O window addresses [POWERPC] celleb: Update celleb_defconfig [POWERPC] celleb: Fix parsing of machine type hack command line option [POWERPC] celleb: Fix PCI config space accesses to subordinate buses [POWERPC] celleb: Fix support for multiple PCI domains [POWERPC] Wire up sys_utimensat [POWERPC] CPM_UART: Removed __init from cpm_uart_init_portdesc to fix warning [POWERPC] User rheap from arch/powerpc/lib [POWERPC] 83xx: Fix the PCI ranges in the MPC834x_MDS device tree. [POWERPC] 83xx: Fix the PCI ranges in the MPC832x_MDS device tree. [POWERPC] CPM_UART: cpm_uart_set_termios should take ktermios, not termios [POWERPC] Change rheap functions to use ulongs instead of pointers ...
2007-05-10Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SPARC64]: Use alloc_pci_dev() in PCI bus probes. [SPARC64]: Bump PROMINTR_MAX to 32. [SPARC64]: Fix recursion in PROM tree building. [SERIAL] sunzilog: Interrupt enable before ISR handler installed [SPARC64] PCI: Consolidate PCI access code into pci_common.c
2007-05-10[S390] Kconfig: menus with depends on HAS_IOMEM.Martin Schwidefsky
Add "depends on HAS_IOMEM" to a number of menus to make them disappear for s390 which does not have I/O memory. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2007-05-09[POWERPC] CPM_UART: Removed __init from cpm_uart_init_portdesc to fix warningKumar Gala
cpm_uart_init_portdesc is referenced from non-init code and thus we were getting the following warning: WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:cpm_uart_init_portdesc from .text between 'cpm_uart_init' (at offset 0x18020) and 'cpm_uart_drv_remove' Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-05-09[POWERPC] CPM_UART: cpm_uart_set_termios should take ktermios, not termiosScott Wood
This eliminates some warnings. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-05-09[POWERPC] Change rheap functions to use ulongs instead of pointersTimur Tabi
The rheap allocation functions return a pointer, but the actual value is based on how the heap was initialized, and so it can be anything, e.g. an offset into a buffer. A ulong is a better representation of the value returned by the allocation functions. This patch changes all of the relevant rheap functions to use a unsigned long integers instead of a pointer. In case of an error, the value returned is a negative error code that has been cast to an unsigned long. The caller can use the IS_ERR_VALUE() macro to check for this. All code which calls the rheap functions is updated accordingly. Macros IS_MURAM_ERR() and IS_DPERR(), have been deleted in favor of IS_ERR_VALUE(). Also added error checking to rh_attach_region(). Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-05-09[SERIAL] sunzilog: Interrupt enable before ISR handler installedMark Fortescue
This patch changes the interrupt enable sequence for the sunzilog driver so that interrupts are not enabled untill after the interrupt handler has been installed. If this is not done, some SS1 and SS2 sun4c systems panic on un-handled interrupt before the handler gets installed preventing boot. It also adds in support for the ESCC version of the zilog chips. The changes mean that the FIFO will be enabled for ESCC versions of the SCC UART. My interpretation of the SCC manual and the existing interrupt handler code is that it sould be able to make good use of the FIFO without issues. Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-08Merge branch 'master' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (77 commits) [POWERPC] Abolish powerpc_flash_init() [POWERPC] Early serial debug support for PPC44x [POWERPC] Support for the Ebony 440GP reference board in arch/powerpc [POWERPC] Add device tree for Ebony [POWERPC] Add powerpc/platforms/44x, disable platforms/4xx for now [POWERPC] MPIC U3/U4 MSI backend [POWERPC] MPIC MSI allocator [POWERPC] Enable MSI mappings for MPIC [POWERPC] Tell Phyp we support MSI [POWERPC] RTAS MSI implementation [POWERPC] PowerPC MSI infrastructure [POWERPC] Rip out the existing powerpc msi stubs [POWERPC] Remove use of 4level-fixup.h for ppc32 [POWERPC] Add powerpc PCI-E reset API implementation [POWERPC] Holly bootwrapper [POWERPC] Holly DTS [POWERPC] Holly defconfig [POWERPC] Add support for 750CL Holly board [POWERPC] Generalize tsi108 PCI setup [POWERPC] Generalize tsi108 PHY types ... Fixed conflict in include/asm-powerpc/kdebug.h manually Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08x86, serial: convert legacy COM ports to platform devicesBjorn Helgaas
Make x86 COM ports into platform devices and don't probe for them if we have PNP. This prevents double discovery, where a device was found both by the legacy probe and by 8250_pnp, e.g., serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A This also means IRDA devices without a UART PNP ID will no longer be claimed by the serial driver, which might require changes in IRDA drivers and administration. In addition to this patch, you may need to configure a setserial init script, e.g., /etc/init.d/setserial, so it doesn't poke legacy UART stuff back in. On Debian, "dpkg-reconfigure setserial" with the "kernel" option does this. To force the old legacy probe behavior even when we have PNPBIOS or ACPI, load the new legacy_serial module (or build 8250 static) with the "legacy_serial.force" option. [akpm@linux-foundation.org: fix makefiles] Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Keith Owens <kaos@ocs.com.au> Cc: Len Brown <lenb@kernel.org> Cc: Adam Belay <ambx1@neo.rr.com> Cc: Matthieu CASTET <castet.matthieu@free.fr> Cc: Jean Tourrilhes <jt@hpl.hp.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Ville Syrjala <syrjala@sci.fi> Cc: Russell King <rmk+serial@arm.linux.org.uk> Cc: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-088250: Remove commented out irq cruftJosh Boyer
Remove some obviously old interrupt disable/enable code that has been commented out. Signed-off-by: Josh Boyer <jwboyer@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08serial_txx9: zap changelog from source codeAtsushi Nemoto
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08serial_txx9: Use assigned device numbersAtsushi Nemoto
The serial_txx9 driver have abused device numbers (major 4, minor 128) if CONFIG_SERIAL_TXX9_STDSERIAL was not set. This patch makes the driver use proper device numbers assigned for it (major 204, minor 196-203). I suppose a typical user of this driver set CONFIG_SERIAL_TXX9_STDSERIAL to Y (i.e. use "ttyS0"), so this patch would not cause big compatibility issue. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08SPIN_LOCK_UNLOCKED cleanup in drivers/serialMilind Arun Choudhary
SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08header cleaning: don't include smp_lock.h when not usedRandy Dunlap
Remove includes of <linux/smp_lock.h> where it is not used/needed. Suggested by Al Viro. Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc, sparc64, and arm (all 59 defconfigs). Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08Subject: jsm driver fix for linuxpps supportLen Sorensen
The jsm driver doesn't currently use the uart_handle_*_change helper functions, which are the obvious place for things like linuxpps to tie into (which it now does of course), and as a result the jsm driver can not be used with linuxpps and anything else that ties into the serial_core helper functions. This patch adds calls to these helper functions whenever the value they manage changes. That actual storage of the state is not modified since the jsm driver caches the current settings (The 8250 driver reads them everytime a user asks for the state), and only updates them whenever they change. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Cc: Scott H Kilau <Scott_Kilau@digi.com> Cc: Wendy Xiong <wendyx@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08Small fixes for jsm driverLen Sorensen
The jsm driver fails when you try to use the TIOCSSERIAL ioctl. The reason is that the driver never sets uart_port.uartclk, causing the data received using TIOCGSERIAL to not match the internal state of the driver. This patch fixes this problem by settings the uartclk to the value used by the serial_core (16 times the baud base). Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Cc: Scott H Kilau <Scott_Kilau@digi.com> Cc: Wendy Xiong <wendyx@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08Merge branch 'linux-2.6'Paul Mackerras
2007-05-07Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SERIAL] sunsu: Fix section mismatch warnings. [SPARC64]: pgtable_cache_init() should be __init. [SPARC64]: Fix section mismatch warnings in arch/sparc64/kernel/prom.c [SPARC64]: Fix section mismatch warnings in arch/sparc64/kernel/pci.c [SPARC64]: Fix section mismatch warnings in arch/sparc64/kernel/console.c [MM]: sparse_init() should be __init. [SPARC64]: Update defconfig. [VIDEO]: Add Sun XVR-2500 framebuffer driver. [VIDEO]: Add Sun XVR-500 framebuffer driver. [SPARC64]: SUN4U PCI-E controller support. [SPARC]: Fix comment typo in smp4m_blackbox_current(). [SCSI] SUNESP: sun_esp.c needs linux/delay.h Fix up conflict in arch/sparc64/mm/init.c manually due to removal of pgtable_cache_init() through the -mm patches (even though that patch was also by David ;) Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (38 commits) sh: R7785RP board updates. sh: Update r7780rp defconfig. sh: Add die chain notifiers. sh: Fix APM emulation on hp6xx. sh: Wire up more IRQs for SH7709. sh: Solution Engine 7722 board support. sh: Fix r7780rp build. sh: kdump support. sh: Move clock reporting to its own proc entry. sh: Solution Engine SH7705 board and CPU updates. serial: sh-sci: Fix module clock refcount for serial console. serial: sh-sci: Fix module clock refcounting. sh: SH7722 clock framework support. sh: hp6xx pata_platform support. sh: Obey CONFIG_HZ for HZ definition. sh: Fix fstatat64() syscall. sh: se7780 PCI support. sh: SH7780 Solution Engine board support. sh: Add a dummy SH-4 PCIC fixup. sh: Tidy up L-BOX area5 addresses. ...
2007-05-07remove unused header file: drivers/serial/crisv10.hRobert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Cc: Mikael Starvik <starvik@axis.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07blackfin: serial driverBryan Wu
This patch implements the driver necessary use the Analog Devices Blackfin processor's Serial Port. Signed-off-by: Bryan Wu <bryan.wu@analog.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Russell King <rmk+lkml@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07Serial: serial_core, use pr_debugJiri Slaby
serial_core, use pr_debug Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07MPSC serial driver tx lockingDave Jiang
The MPSC serial driver assumes that interrupt is always on to pick up the DMA transmit ops that aren't submitted while the DMA engine is active. However when irqs are off for a period of time such as operations under kernel crash dump console messages do not show up due to additional DMA ops are being dropped. This makes console writes to process through all the tx DMAs queued up before submitting a new request. Also, the current locking mechanism does not protect the hardware registers and ring buffer when a printk is done during the serial write operations. The additional per port transmit lock provides a finer granular locking and protects registers being clobbered while printks are nested within UART writes. Signed-off-by: Dave Jiang <djiang@mvista.com> Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07serial: define FIXED_PORT flag for serial_coreDavid Gibson
At present, the serial core always allows setserial in userspace to change the port address, irq and base clock of any serial port. That makes sense for legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports at peculiar addresses. In these cases, the kernel code configuring the ports must know exactly where they are, and their clocking arrangements (which can be unusual on embedded boards). It doesn't make sense for userspace to change these settings. Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port structure. If this flag is set when the serial port is configured, any attempts to alter the port's type, io address, irq or base clock with setserial are ignored. In addition this patch uses the new flag for on-chip serial ports probed in arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports probed by drivers/serial/of_serial.c. Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07RM9000 serial driverThomas Koeller
Add support for the integrated serial ports of the MIPS RM9122 processor and its relatives. The patch also does some whitespace cleanup. [akpm@linux-foundation.org: cleanups] Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07serial driver PMC MSP71xxMarc St-Jean
Serial driver patch for the PMC-Sierra MSP71xx devices. There are three different fixes: 1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard 16550 in that the THRE interrupt will not re-assert itself simply by disabling and re-enabling the THRI bit in the IER, it is only re-enabled if a character is actually sent out. It appears that the "8250-uart-backup-timer.patch" in the "mm" tree also fixes it so we have dropped our initial workaround. This patch now needs to be applied on top of that "mm" patch. 2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature which causes a new Busy Detect interrupt to be generated if it's busy when the LCR is written. This fix saves the value of the LCR and rewrites it after clearing the interrupt. 3 Workaround for interrupt/data concurrency issue: The SoC needs to ensure that writes that can cause interrupts to be cleared reach the UART before returning from the ISR. This fix reads a non-destructive register on the UART so the read transaction completion ensures the previously queued write transaction has also completed. Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07[POWERPC] Don't shutdown TX on mpc5200 serial port if it is a consoleGrant Likely
If the serial port gets shut down, then console output stalls. 9 out of 10 kernel hackers agree, this is a bad thing. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-07[POWERPC] Rename device_is_compatible to of_device_is_compatibleStephen Rothwell
for consistency with other Open Firmware interfaces (and Sparc). This is just a straight replacement. This leaves the compatibility define in place. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-07[SERIAL] sunsu: Fix section mismatch warnings.David S. Miller
Mark sunsu_console_setup() as __init and rename 'sunsu_cons' to 'sunsu_console' so that it matches modpost.c's whitelist. Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-07serial: sh-sci: Fix module clock refcount for serial console.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07serial: sh-sci: Fix module clock refcounting.dmitry pervushin
This adds the enable/disable hooks for the port clock to sh-sci. Signed-off-by: dmitry pervushin <dimka@nomadgs.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07sh: MS7712SE01 board support.Nobuhiro Iwamatsu
Support the SH7712 (SH3-DSP) Solution Engine reference board. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07serial: sh-sci: Kill off breakpoint in break IRQ.Paul Mundt
With the GDB stub being entered via a special sysrq trigger, we don't want to hit it directly from sci_br_interrupt(). Without this, there is access to the other sysrq triggers when kgdb is enabled. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07sh: Add SH7785 Highlander board support (R7785RP).Paul Mundt
This adds preliminary support for the SH7785-based Highlander board. Some of the Highlander support code is reordered so that most of it can be reused directly. This also plugs in missing SH7785 checks in the places that need it, as this is the first board to support the CPU. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07sh: Bring kgdb back from the dead.Paul Mundt
This code has suffered quite a bit of bitrot, do some basic tidying to get it to a reasonably functional state again. This gets the basic support and the console working again. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-06Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (82 commits) [ARM] Add comments marking in-use ptrace numbers [ARM] Move syscall saving out of the way of utrace [ARM] 4360/1: S3C24XX: regs-udc.h remove unused macro [ARM] 4358/1: S3C24XX: mach-qt2410.c: remove linux/mmc/protocol.h header [ARM] mm 10: allow memory type to be specified with ioremap [ARM] mm 9: add additional device memory types [ARM] mm 8: define mem_types table L1 bit 4 to be for ARMv6 [ARM] iop: add missing parens in macro [ARM] mm 7: remove duplicated __ioremap() prototypes ARM: OMAP: fix OMAP1 mpuio suspend/resume oops ARM: OMAP: MPUIO wake updates ARM: OMAP: speed up gpio irq handling ARM: OMAP: plat-omap changes for 2430 SDP ARM: OMAP: gpio object shrinkage, cleanup ARM: OMAP: /sys/kernel/debug/omap_gpio ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon ARM: OMAP: Enable 24xx GPIO autoidling [ARM] 4318/2: DSM-G600 Board Support [ARM] 4227/1: minor head.S fixups [ARM] 4328/1: Move i.MX UART regs to driver ...
2007-05-06Merge branches 'arm-mm', 'at91', 'clkevts', 'imx', 'iop', 'misc', 'netx', ↵Russell King
'ns9xxx', 'omap', 'pxa', 'rpc', 's3c' and 'sa1100' into devel
2007-05-03[ARM] 4328/1: Move i.MX UART regs to driverSascha Hauer
This patch moves the i.MX UART register descriptions from include/asm-arm/arch-imx/imx-regs.h to the serial driver itself. This helps using the driver on other architectures like mx31 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-03[ARM] 4357/1: AT91: Support slower serial baud-ratesAndrew Victor
Allow slower serial baud-rates by switching the UART clock from MCK to MCK/8. Based on patches by Mike Wolfram and Russell King. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-02[POWERPC] Rename get_property to of_get_property: driversStephen Rothwell
These are all the remaining instances of get_property. Simple rename of get_property to of_get_property. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-04-30Merge branch 'linux-2.6' into for-2.6.22Paul Mackerras
2007-04-26Revert "[POWERPC] Rename get_property to of_get_property: drivers"Paul Mackerras
This reverts commit d05c7a80cf39ae7d0f8d0c3e47c93d51fcd393d3, which included changes which should go via other subsystem maintainers.
2007-04-26[SPARC/64] constify of_get_property return: driversStephen Rothwell
The only unfortunate bit here is that the name field of struct map_info is not const, so for now we put a cast on the assignment of it. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-248250: fix possible deadlock between serial8250_handle_port() and ↵Jiri Kosina
serial8250_interrupt() Commit 40b36daa introduced possibility that serial8250_backup_timeout() -> serial8250_handle_port() locks port.lock without disabling irqs, thus allowing deadlock against interrupt handler (port.lock is acquired in serial8250_interrupt()). Spotted by lockdep. Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alex Williamson <alex.williamson@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>