aboutsummaryrefslogtreecommitdiff
path: root/drivers/spi
AgeCommit message (Collapse)Author
2007-12-05spi: initial BF54x SPI supportBryan Wu
Initial BF54x SPI support - support BF54x SPI0 - clean up some code (whitespace etc) - will support multiports in the future - start using portmux calls Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05spi: simplify spi_sync() calling conventionMarc Pignat
Simplify spi_sync calling convention, eliminating the need to check both the return value AND the message->status. In consequence, this corrects misbehaviours of spi_read and spi_write (which only checked the former) and their callers. Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05spi: at25 driver is for EEPROM not FLASHDavid Brownell
Add comment to at25 driver that it's for EEPROM chips, not FLASH chips ... the AT25 series has both types of chip, and sometimes they're even pin-compatible. The command sets are different, as is the treatment of erasure. (FLASH needs explicit erasure, but with EEPROM it's implicit.) Note that all vendors seem to have this same confusion in their *25* series SPI memory parts. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05SPI: use mutex not semaphoreDavid Brownell
Make spi_write_then_read() use a mutex not a binary semaphore. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-29spi: S3C2410: add bus number to SPI GPIO driverDavid Brownell
Allow passing a bus number through the platform data for the S3C2410 SPI GPIO driver. This is needed to support multiple SPI busses. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-29S3C24XX: ensure we only configure valid GPIOsBen Dooks
If we specify an GPIO which cannot be used for the purpose, then assume that the GPIO is not to be used and do not try and configure it. This can be the case where the SPI bus is TX only. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-29atmel_spi: label GPIOs betterDavid Brownell
Make the atmel_spi driver label GPIOs according to the device for which they're acting as a chipselect. This way the debugfs dump of gpio state is more informative. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-23Blackfin arch: punt CONFIG_BFIN -- we already have CONFIG_BLACKFINMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-14tle62x0 driver stops ignoring read errorsDavid Brownell
The tle62x0 driver was ignoring all read errors. This patch makes it pass such errors up the stack, instead of returning bogus data. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-14spi: fix error paths on txx9spi_probeAtsushi Nemoto
Some error paths in txx9spi_probe wrongly return 0. This patch fixes them by using the devres interfaces. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-14spi: fix double-free on spi_unregister_masterAtsushi Nemoto
After 49dce689ad4ef0fd1f970ef762168e4bd46f69a3, device_for_each_child iteration hits the master device itself. Do not call spi_unregister_device() for the master device. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Acked-by: David Brownell <david-b@pacbell.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-29fix abuses of ptrdiff_tAl Viro
Use of ptrdiff_t in places like - if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len)) + if (!access_ok(VERIFY_WRITE, (u8 __user *) + (ptrdiff_t) u_tmp->rx_buf, + u_tmp->len)) is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general we are not even promised that ptrdiff_t is large enough to hold a pointer, just enough to hold a difference between two pointers within the same object). For another, it confuses the fsck out of sparse. Use unsigned long or uintptr_t instead. There are several places misusing ptrdiff_t; fixed. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-19Fix misspellings of "system", "controller", "interrupt" and "necessary".Robert P. J. Day
Fix the various misspellings of "system", controller", "interrupt" and "[un]necessary". Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-18Add missing newlines to some uses of dev_<level> messagesJoe Perches
Found these while looking at printk uses. Add missing newlines to dev_<level> uses Add missing KERN_<level> prefixes to multiline dev_<level>s Fixed a wierd->weird spelling typo Added a newline to a printk Signed-off-by: Joe Perches <joe@perches.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Roland Dreier <rolandd@cisco.com> Cc: Tilman Schmidt <tilman@imap.cc> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Greg KH <greg@kroah.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Cc: James Smart <James.Smart@Emulex.Com> Cc: Andrew Vasquez <andrew.vasquez@qlogic.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Jaroslav Kysela <perex@suse.cz> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16spi doesn't need class_deviceTony Jones
Make the SPI framework and drivers stop using class_device. Update docs accordingly ... highlighting just which sysfs paths should be "safe"/stable. Signed-off-by: Tony Jones <tonyj@suse.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16spi_mpc83xx handles other processors with QUICC engineAnton Vorontsov
Currently, all QE SPI controllers are almost the same comparing to MPC83xx's, thus let's use that driver for them. Tested to work on MPC85xx in loopback mode. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16SPI driver runtime footprint shrinkageDavid Brownell
Shrink the runtime footprint of various SPI drivers: - Move the probe() routine into the init section where practical, using platform_driver_probe() to make that safe. This often saves around 1KB. Using platform_driver_probe() can also be a correctness fix, if the probe routine is already marked __init but the driver struct keeps a dangling pointer to it after init section removal. - Likewise move remove() routines into the exit sections. These changes would be inappropriate iff the platform devices were actually hotpluggable (e.g. they're found on optional addon cards, or in an FPGA that's dynamically reprogrammed). In these cases, that's not the situation; it's an SOC controller and the only device is initialized before these drivers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16OMAP2 McSPI code cleanupKyungmin Park
Remove unused variable & write space Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16Clean up duplicate includes in drivers/spi/Jesper Juhl
This patch cleans up duplicate includes in drivers/spi/ Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-12Driver core: change add_uevent_var to use a structKay Sievers
This changes the uevent buffer functions to use a struct instead of a long list of parameters. It does no longer require the caller to do the proper buffer termination and size accounting, which is currently wrong in some places. It fixes a known bug where parts of the uevent environment are overwritten because of wrong index calculations. Many thanks to Mathieu Desnoyers for finding bugs and improving the error handling. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-09-11spi_mpc83xx: hang fixJan Andersson
When the spi_mpc83xx driver receives a tx_buf pointer which is NULL, it only writes one zero filled word to the transmit register. If the driver expects to receive more than one word it will wait forever for a second receive interrupt. With this patch the controller will shift out zeroes until all words have been received. Signed-off-by: Jan Andersson <jan@gaisler.com> Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-31Fix typo in atmel_spi.cAndrew Victor
Fix cut 'n paste bug in Atmel SPI driver. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Acked-by: David Brownell <david-b@pacbell.net> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-31spi: correct name for spi_txx9Atsushi Nemoto
Correct the name of the spi_txx9 driver (and their in-tree user) instead of MODULE_ALIAS workaround. This would be preferable in the long term. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-31SPI driver hotplug/coldplug fixesDavid Brownell
Update various SPI drivers so they properly support - coldplug through "modprobe $(cat /sys/devices/.../modalias)" - hotplug through "modprobe $(MODALIAS)" The basic rule for platform, SPI, and (new style) I2C drivers is just to make sure that modprobing the driver name works. In this case, all the relevant drivers are platform drivers, and this patch either (a) Changes the driver name, if no in-tree code would break; this is simpler and thus preferable in the long term. (b) Adds MODULE_ALIAS directives, when in-tree platforms declare devices using the current driver name; less desirable. Most systems will link SPI controller drivers statically, but there's no point in being needlessly broken. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Jean Delvare <khali@linux-fr.org> Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-11spidev warning fixDavid Brownell
Git rid of "warning: passing arg 2 of `access_ok' makes pointer from integer without a cast" reported on SH ... most architectures use macros in that test, SH uses inlined functions. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-11spi_mpc83xx: fix prescale modulus calculationAnton Vorontsov
Long ago I've noticed (but didn't pay much attention) that spi_mpc83xx using PM calculations that differs from what specs describe. I.e. u8 pm = mpc83xx_spi->spibrg / (spi->max_speed_hz * 4); While specs says: "The SPI baud rate generator clock source (either system clock or system clock divided by 16, depending on DIV16 bit) is divided by 4 * ([PM] + 1), a range from 4 to 64.". Thus " - 1" is missing in the spi_mpc83xx's formula. Why nobody noticed that bug? Probably because sysclk usually less then user expects, e.g. you expect 200 MHz, but real clock is 198 MHz, and integer rounding helps when this formula is used. Suppose it's SPI in QE, SYSCLK at 198 MHz, thus SPIBRG at 99MHz, 25 MHz requested. PM = (99MHz / ( 25 MHz * 4 )), PM == 0, output SPICLK will be 24.75 MHz At lower frequencies this bug is more noticeable, though. And this bug shows itself in all its beauty if SYSCLK is equal or a bit more than you expect (200 MHz SYSCLK, 100 MHz SPIBRG): PM = (100MHz / ( 25 MHz * 4 )), PM == 1, output SPICLK will be 12.625 MHz! Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-11spi_mpc83xx: in "QE mode", use sysclk/2Anton Vorontsov
For MPC8349E input to the SPI Baud Rate Generator is SYSCLK, but it's SYSCLK/2 for MPC8323E (SPI in QE). Fix this, and remove confusion by renaming the mpc83xx_spi->sysclk member as mpc83xx_spi->spibrg. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spi device setup gets better error checkingDavid Brownell
This updates some error reporting paths in SPI device setup: - Move validation logic for SPI chipselects to spi_new_device(), which is where it should always have been. - In spi_new_device(), emit error messages if the device can't be created. This is LOTS better than a silent failure; though eventually, the calling convention should probably change to use the <linux/err.h> conventions. - Includes one previously-missing check: SPI masters must always have at least one chipselect, even for dedicated busses which always keep it selected! It also adds a FIXME (IDR for dynamic ID allocation) so the issue doesn't live purely in my mailbox. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spi_mpc83xx: support loopback modeAnton Vorontsov
This exposes the hardware loopback mode to drivers, primarily for testing. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spidev supports more communications modesAnton Vorontsov
The spidev driver doesn't currently expose all SPI communications modes to userspace. This passes them all through to the driver. Two of them are potentially troublesome, in the sense that they could cause hardware conflicts on shared busses. It might be appropriate to add some privilege checks for for those modes. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spi_mpc83xx: fix QE+LSB mode shiftsAnton Vorontsov
spi_mpc83xx should use other shifts when running in QE+LSB mode. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spi_mpc83xx: support for lsb-first transfersAnton Vorontsov
This controller supports LSB-first transfers; let drivers use them. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spi_mpc83xx: get rid of magic numbersAnton Vorontsov
Magic-numbers-R-Evil Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spi_mpc83xx: turn off SPI unit while switching modeAnton Vorontsov
Documentation clearly states, that mode should not be changed till SPMODE_ENABLE bit set. I've seen hangs w/o this patch. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-26fixup s3c24xx build after arch movesBen Dooks
Fix the include files moved around during the s3c24xx arch moves. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-21spi.c:scan_boardinfo() mustn't be __init_or_moduleAdrian Bunk
WARNING: drivers/built-in.o(.text+0x889735): Section mismatch: reference to .init.text:scan_boardinfo (between 'spi_register_master' and '__unregister') Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17use mutex instead of semaphore in SPI core/init codeMatthias Kaehlcke
The SPI core/init code uses a semaphore as mutex. Use the mutex API instead of the (binary) semaphore. Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17spi_txx9 controller driverAtsushi Nemoto
This is a driver for SPI controller built into TXx9 MIPS SoCs. This driver is derived from arch/mips/tx4938/toshiba_rbtx4938/spi_txx9.c. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17SPI: omap2_mcspi driverSamuel Ortiz
Add OMAP24XX McSPI (Multichannel SPI) controller driver. This driver is tested very well under OMAP GIT tree with N800 - Nokia Internet Tablet, and some other OMAP2 boards. Recent updates included bugfixes, cleanups, speedups, and better conformance to the current SPI programming interface. This doesn't yet understand the third controller instance on the OMAP 2430. [david-b@pacbell.net: more minor cleanups to the omap2_mcspi driver] Signed-off-by: Juha Yrjölä <juha.yrjola@solidboot.com> Signed-off-by: Trilok Soni <soni.trilok@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17spi_mpc83xx.c: support QE enabled 83xx CPU's like mpc832xJoakim Tjernlund
Quicc Engine enabled mpc83xx CPU's has a somewhat different HW interface to the SPI controller. This patch adds a qe_mode knob that sees to that needed adaptions are performed. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17SPI master driver for Xilinx virtexAndrei Konovalov
Simple SPI master driver for Xilinx SPI controller. No support for multiple masters. Not using level 1 drivers from EDK. [akpm@linux-foundation.org: uninlining] Signed-off-by: Yuri Frolov <yfrolov@ru.mvista.com> Signed-off-by: Andrei Konovalov <akonovalov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17SPI: tle620x power switch driverBen Dooks
Add support for the Infineon TLE62x0 series of low-side driver chips, such as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized for power switching applications. The driver provides a userspace interface to those GPIOs, and to the switch status they provide. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17S3c24xx SPI controllers both select 'bitbang'David Brownell
Tweak Kconfig for the S3C24XX SPI controller drivers. Both use the bitbang framework; only one previously said that. Plus in this case "select" is the right way to manage that dependency, since folk will not know up front to enable bitbang in order to even see those S3C drivers in order to enable them. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17atmel_spi: don't always deselect chip between messagesDavid Brownell
Update chipselect handling for atmel_spi: * Teach it how to leave chipselect active between messages; this helps various drivers work better. * Cope with at91rm0200 errata: nCS0 can't be managed with GPIOs. The MR.PCS value is now updated whenever a chipselect changes. (This requires SPI pinmux init for that controller to change, and also testing on rm9200; doesn't break at91sam9 or avr32.) * Fix minor glitches: spi_setup() must leave chipselects inactive, as must removal of the spi_device. Also tweak diagnostic messaging to be a bit more useful. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17atmel_spi: minor updatesDavid Brownell
Minor updates to atmel_spi: - DMA: * Comments to explain the DMA policies * Report any mapping errors from spi_transfer() * Remove extra loop for DMA mapping - Diagnostics: report minimum clock rate, if we need to reject a spi_setup() request because that rate is too low. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17spi_mpc83xx.c underclocking hotfixClifford Wolf
The MPC83xx SPI controller clock divider can divide the system clock by not more then 1024. The spi_mpc83xx driver does not check this and silently writes garbage to the SPI controller registers when asked to run at lower frequencies. I've tried to run the SPI on a 266MHz MPC8349E with 100kHz for debugging a bus problem and suddenly was confronted with a 2nd problem to debug.. ;-) The patch adds an additional check which avoids writing garbage to the SPI controller registers and warn the user about it. This might help others to avoid simmilar problems. Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17spi_lm70llp parport adapter driverKaiwan N Billimoria
This adds a driver for the LM70-LLP parport adapter, which is an eval board for the LM70 temperature sensor. For those without that board, it may be a simpler example of a parport-to-SPI adapter then spi_butterfly. Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com> Doc, coding style, and interface updates; build fixes. Minor rename. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17spidev compiler warning goneDavid Brownell
Get rid of annoying GCC warning on 32-bit platforms. drivers/spi/spidev.c: In function 'spidev_message': drivers/spi/spidev.c:184: warning: cast to pointer from integer of different size drivers/spi/spidev.c:216: warning: cast to pointer from integer of different size The trick is to add an extra cast using "ptrdiff_t" to convert the u64 to the correct size integer, and only then casting it into a "void *" pointer. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17SPI controller drivers: check for unsupported modesDavid Brownell
Minor SPI controller driver updates: make the setup() methods reject spi->mode bits they don't support, by masking aginst the inverse of bits they *do* support. This insures against misbehavior later when new mode bits get added. Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH. Support for all four SPI clock/transfer modes is routine. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-11sysfs: add parameter "struct bin_attribute *" in .read/.write methods for ↵Zhang Rui
sysfs binary attributes Well, first of all, I don't want to change so many files either. What I do: Adding a new parameter "struct bin_attribute *" in the .read/.write methods for the sysfs binary attributes. In fact, only the four lines change in fs/sysfs/bin.c and include/linux/sysfs.h do the real work. But I have to update all the files that use binary attributes to make them compatible with the new .read and .write methods. I'm not sure if I missed any. :( Why I do this: For a sysfs attribute, we can get a pointer pointing to the struct attribute in the .show/.store method, while we can't do this for the binary attributes. I don't know why this is different, but this does make it not so handy to use the binary attributes as the regular ones. So I think this patch is reasonable. :) Who benefits from it: The patch that exposes ACPI tables in sysfs requires such an improvement. All the table binary attributes share the same .read method. Parameter "struct bin_attribute *" is used to get the table signature and instance number which are used to distinguish different ACPI table binary attributes. Without this parameter, we need to offer different .read methods for different ACPI table binary attributes. This is impossible as there are various ACPI tables on different platforms, and we don't know what they are until they are loaded. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>