aboutsummaryrefslogtreecommitdiff
path: root/drivers/usb/musb
AgeCommit message (Collapse)Author
2009-06-15usb: musb: disable OTG AUTOIDLE only with omap3430Niilo Minkkinen
Omap3 MUSB AUTOIDLE functionality configured through OTG_SYSCONFIG register prevents the device from going into retention. This is a workaround (by Richard Woodruff/TI), as his comment : > A new MUSB bug which is a match to data below was identified very > recently (on hardware and in simulation). > This bug is in 3430 and not 3630. > As a priority test (and as new default) you should have engineers > disable autoidle for MUSB block. > This is the workaround which will show up in next errata. Signed-off-by: Niilo Minkkinen <ext-niilo.1.minkkinen@nokia.com> Signed-off-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb: add high bandwidth ISO supportAjay Kumar Gupta
Tested on OMAP3 host side with Creative (Live! Cam Optia) USB camera which uses high bandwidth isochronous IN endpoints. FIFO mode 4 is updated to provide the needed 4K endpoint buffer without breaking the g_nokia composite gadget configuration. (This is the only gadget driver known to use enough endpoints to notice the change.) Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-15musb: use dma mode 1 for TX if transfer size equals maxpacket (v2)Anand Gadiyar
Currently, with Inventra DMA, we use Mode 0 if transfer size is less than or equal to the endpoint's maxpacket size. This requires that we explicitly set TXPKTRDY for that transfer. However the musb_g_tx code will not set TXPKTRDY twice if the last transfer is exactly equal to maxpacket, even if request->zero is set. Using Mode 1 will solve this; a better fix might be in musb_g_tx(). Without this change, musb will not correctly send out a ZLP if the last transfer is the maxpacket size and request->zero is set. Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb: support disconnect after HNP roleswitchDavid Brownell
Adjust HNP state machines in MUSB driver so that they handle the case where the cable is disconnected. The A-side machine was very wrong (unrecoverable); the B-Side was much less so. - A_PERIPHERAL ... as usual, the non-observability of the ID pin through Mentor's registers makes trouble. We can't go directly to A_WAIT_VFALL to end the session and start the disconnect processing. We can however sense link suspending, go to A_WAIT_BCON, and from there use OTG timeouts to finally trigger that A_WAIT_VFALL transition. (Hoping that nobody reconnects quickly to that port and notices the wrong state.) - B_HOST ... actually clear the Host Request (HR) bit as the messages say, disconnect the peripheral from the root hub, and don't detour through a suspend state. (In some cases this would eventually have cleaned up.) Also adjust the A_SUSPEND transition to respect the A_AIDL_BDIS timeout, so if HNP doesn't trigger quickly enough the A_WAIT_VFALL transition happens as it should. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb: make initial HNP roleswitch work (v2)David Brownell
Minor HNP bugfixes, so the initial role switch works: - A-Device: * disconnect-during-suspend enters A_PERIPHERAL state * kill OTG timer after reset as A_PERIPHERAL ... * ... and also pass that reset to the gadget * once HNP succeeds, clear the "ignore_disconnect" flag * from A_PERIPHERAL, disconnect transitions to A_WAIT_BCON - B-Device: * kill OTG timer on entry to B_HOST state (HNP succeeded) * once HNP succeeds, clear "ignore_disconnect" flag * kick the root hub only _after_ the state is adjusted Other state transitions are left alone. Notably, exit paths from the "roles have switched" state ... A_PERIPHERAL handling of that stays seriously broken. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb: otg timer cleanupDavid Brownell
Minor cleanup of OTG timer handling: * unify decls for OTG time constants, in the core header * set up and use that timer in a more normal way * move to the driver struct, so it's usable outside core And tighten use and setup of T(a_wait_bcon) so that if it's used, it's always valid. (If that timer expires, the A-device will stop powering VBUS. For non-OTG systems, that will be a surprise.) No behavioral changes, other than more consistency when applying that core HNP timeout. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb: proper hookup to transceiver driversDavid Brownell
Let the otg_transceiver in MUSB be managed by an external driver; don't assume it's integrated. OMAP3 chips need it to be external, and there may be ways to interact with the transceiver which add functionality to the system. Platform init code is responsible for setting up the transeciver, probably using the NOP transceiver for integrated transceivers. External ones will use whatever the board init code provided, such as twl4030 or something more hands-off. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb: split out CPPI interrupt handlerSergei Shtylyov
As DaVinci DM646x has a dedicated CPPI DMA interrupt, replace cppi_completion() (which has always been kind of layering violation) by a complete CPPI interrupt handler. [ dbrownell@users.sourceforge.net: only cppi_dma.c needs platform device header, not cppi_dma.h ] Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb_host: refactor URB givebackSergei Shtylyov
As musb_advance_schedule() is now the only remaning caller of musb_giveback() (and the only valid context of such call), just fold the latter into the former and then rename __musb_giveback() into musb_giveback(). This is a net minor shrink. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb_host: streamline musb_cleanup_urb() callsSergei Shtylyov
The argument for the 'is_in' parameter of musb_cleanup_urb() is always extracted from an URB that's passed to the function. So that parameter is superfluous; remove it. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb_host: simplify check for active URBSergei Shtylyov
The existance of the scheduling list shouldn't matter in determining whether there's currectly an URB executing on a hardware endpoint. What should actually matter is the 'in_qh' or 'out_qh' fields of the 'struct musb_hw_ep' -- those are set in musb_start_urb() and cleared in musb_giveback() when the endpoint's URB list drains. Hence we should be able to replace the big *switch* statements in musb_urb_dequeue() and musb_h_disable() with mere musb_ep_get_qh() calls... While at it, do some more changes: - add 'is_in' variable to musb_urb_dequeue(); - remove the unnecessary 'epnum' variable from musb_h_disable(); - fix the comment style in the vicinity. This is a minor shrink of source and object code. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb_host: factor out musb_ep_{get|set}_qh()Sergei Shtylyov
Factor out the often used code to get/set the active 'qh' pointer for the hardware endpoint. Change the way the case of a shared FIFO is handled by setting *both* 'in_qh' and 'out_qh' fields of 'struct musb_hw_ep'. That seems more consistent and makes getting to the current 'qh' easy when the code knows the direction beforehand. While at it, turn some assignments into intializers and fix declaration style in the vicinity. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb_host: refactor musb_save_toggle() (take 2)Sergei Shtylyov
Refactor musb_save_toggle() as follows: - replace 'struct musb_hw_ep *ep' parameter by 'struct musb_qh *qh' to avoid re-calculating this value - move usb_settogle() call out of the *if* operator. This is a net minor shrink of source and object code. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb_gadget: suppress "parasitic" TX interrupts with CPPISergei Shtylyov
Suppress "parasitic" endpoint interrupts in the DMA mode when using CPPI DMA driver; they're caused by the MUSB gadget driver using the DMA request mode 0 instead of the mode 1. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15musb_gadget: fix unhandled endpoint 0 IRQsSergei Shtylyov
The gadget EP0 code routinely ignores an interrupt at end of the data phase because of musb_g_ep0_giveback() resetting the state machine to "idle, waiting for SETUP" phase prematurely. The driver also prematurely leaves the status phase on receiving the SetupEnd interrupt. As there were still unhandled endpoint 0 interrupts happening from time to time after fixing these issues, there turned to be yet another culprit: two distinct gadget states collapsed into one. The (missing) state that comes after STATUS IN/OUT states was typically indiscernible from them since the corresponding interrupts tend to happen within too little period of time (due to only a zero-length status packet in between) and so they got coalesced; yet this state is not the same as the next one which is associated with the reception of a SETUP packet. Adding this extra state seems to have fixed the rest of the unhandled interrupts that generic_interrupt() and davinci_interrupt() hid by faking their result and only emitting a debug message -- so, stop doing that. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-23USB: musb: fix build when !CONFIG_PMAlexander Beregalov
Fix this build error when CONFIG_PM is not set: drivers/usb/musb/musb_core.c:2232: error: 'musb_resume_early' undeclared here Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-23USB: musb: Remove my email address from few musb related driversJarkko Nikula
This email address is going to expire soon and my contribution to musb is next to zero so remove it. Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-17USB: musb: fix possible panic while resumingKim Kyuwon
During driver resume processing, musb could cause a kernel panic. Fix by enabling the clock earlier, with the resume_early method. Signed-off-by: Kim Kyuwon <q1.kim@samsung.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-17USB: musb: fix isochronous TXDMA (take 2)Sergei Shtylyov
Multi-frame isochronous TX URBs transfers in DMA mode never complete with CPPI DMA because musb_host_tx() doesn't restart DMA on the second frame, only emitting a debug message. With Inventra DMA they complete, but in PIO mode. To fix: - Factor out programming of the DMA transfer from musb_ep_program() into musb_tx_dma_program(); - Reorder the code at the end of musb_host_tx() to facilitate the fallback to PIO iff DMA fails; - Handle the buffer offset consistently for both PIO and DMA modes; - Add an argument to musb_ep_program() for the same reason (it only worked correctly with non-zero offset of the first frame in PIO mode); - Set the completed isochronous frame descriptor's 'actual_length' and 'status' fields correctly in DMA mode. Also, since CPPI reportedly doesn't like sending isochronous packets in the RNDIS mode, change the criterion for this mode to be used only for multi-packet transfers. (There's no need for that mode in the single-packet case anyway.) [ dbrownell@users.sourceforge.net: split comment paragraph into bullet list, shrink patch delta, style tweaks ] Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-17USB: musb: sanitize clearing TXCSR DMA bits (take 2)Sergei Shtylyov
The MUSB code clears TXCSR_DMAMODE incorrectly in several places, either asserting that TXCSR_DMAENAB is clear (when sometimes it isn't) or clearing both bits together. Recent versions of the programmer's guide require DMAENAB to be cleared first, although some older ones didn't. Fix this and while at it: - In musb_gadget::txstate(), stop clearing the AUTOSET and DMAMODE bits for the CPPI case since they never get set anyway (the former bit is reserved on DaVinci); but do clear the DMAENAB bit on the DMA error path. - In musb_host::musb_ep_program(), remove the duplicate DMA controller specific code code clearing the TXCSR previous state, add the code to clear TXCSR DMA bits on the Inventra DMA error path, to replace such code (executed late) on the PIO path. - In musbhsdma::dma_channel_abort()/dma_controller_irq(), add/use the 'offset' variable to avoid MUSB_EP_OFFSET() invocations on every RXCSR/TXCSR access. [dbrownell@users.sourceforge.net: don't introduce CamelCase, shrink diff] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-17USB: musb: bugfixes for multi-packet TXDMA supportSergei Shtylyov
We really want to use DMA mode 1 for all multi-packet transfers; that's one IRQ on DMA completion, instead of one per packet. There is an important issue with such transfers, especially on the host side: when such transfers end with a full-size packet, we must defer musb_dma_completion() calls until the FIFO empties. Else we report URB completions too soon, and may clobber data in the FIFO fifo when writing the next packet (losing data). The Inventra DMA support uses DMA mode 1, but it ignores that issue. The CPPI DMA support uses mode 0, but doesn't handle its TXPKTRDY interrupts quite right either; it can get stale "packet ready" interrupts, and report transfer completion too early using slightly different code paths, also losing data. So I'm solving it in a generic way -- by adding a sort of the "interrupt filter" into musb_host_tx(), catching these cases where a DMA completion IRQ doesn't suffice and removing some needlessly controller-specific logic. When a TXDMA interrupt happens and DMA request mode 1 is active, that filter resets to mode 0 and defers URB completion processing until TXPKTRDY, unless the FIFO is already empty. Related filtering logic in Inventra and CPPI code gets removed. Since it should be competely safe now to use the DMA request mode 1 for host side transfers with the CPPI DMA controller, set it in musb_h_tx_dma_start() ... now renamed (and shared). [ dbrownell@users.sourceforge.net: don't introduce more CamElCase; use more concise explanations ] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-17USB: musb_host, fix ep0 fifo flushingDavid Brownell
The MUSB host side can't share generic TX FIFO flush logic with EP0; the EP0 TX status register bits are different from those for other entpoints. Resolve this issue by providing a new EP0-specific routine to flush and reset the FIFO, which pays careful attention to restrictions listed in the latest programmer's guide. This gets rid of an open issue whereby the usbtest control write test (#14) failed. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-17USB: musb_host, minor enqueue locking fix (v2)David Brownell
Someone noted that the enqueue path used an unlocked access for usb_host_endpoint->hcpriv ... fix that, by being safe and always accessing it under spinlock protection. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: musb: partial DaVinci dm355 supportDavid Brownell
Partial support for DaVinci DM355, on the EVM board; peripheral mode should work, once mainline merges DM355 support. Missing: (a) renumbering the GPIO for DRVVBUS on the DM6446 EVM, when DAVINCI_N_GPIO increases; (b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is driven according to the ID signal, if cpu_is_..._dm355() The new PHY control bits are ignored on DM6446. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: musb: only turn off vbus in OTG hostsAjay Kumar Gupta
Except on DaVinci, VBUS is now switched off as part of idling the USB link (after a_wait_bcon) whenever a device is disconnected from host. This is correct for OTG hosts, where either SRP or an ID interrupt could turn VBUS on again. However, for non-OTG hosts there's no way to turn VBUS on again, so the host becomes unusable. And the procfs entry which once allowed a manual workaround for this is now gone. This patch adds an is_otg_enabled() check before scheduling the switch-off timer in disconnect path, supporting a "classic host" mode where SRP is unavailable. [ dbrownell@users.sourceforge.net: tweak patch description ] Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: musb: fix init oops crash with static FIFO configGiuseppe GORGOGLIONE
Correct musb_read_fifosize() and musb_configure_ep0() functions for the #ifndef BLACKFIN branch when the silicon uses static FIFO configuration. (Most current silicon configures this controller to use dynamic FIFO configuration; some parts from ST don't, like the STM STA2062.) Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: musb: NAK timeout scheme on bulk RX endpointAjay Kumar Gupta
Fixes endpoint starvation issue when more than one bulk QH is multiplexed on the reserved bulk RX endpoint, which is normal for cases like serial and ethernet adapters. This patch sets the NAK timeout interval for such QHs, and when a timeout triggers the next QH will be scheduled. (This resembles the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.) This scheme doesn't work for devices which are connected to a high to full speed tree (transaction translator) as there is no NAK timeout interrupt from the musb controller from such devices. Tested with PIO, Inventra DMA, CPPI DMA. [ dbrownell@users.sourceforge.net: fold in start_urb() update; clarify only for bulk RX; don't accidentally clear WZC bits ] Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: musb: rewrite host periodic endpoint allocationSergei Shtylyov
The current MUSB host code doesn't make use of all the available FIFOs in for periodic transfers since it wrongly assumes the RX and TX sides of any given hw_ep always share one FIFO. Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep' to check the endpoint's business; get rid of the now-unused 'periodic' array in the 'struct musb'. Also optimize a loop induction variable in the endpoint lookup code. (Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>) [ dbrownell@users.sourceforge.net: clarify description and origin of this fix; whitespace ] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: replace uses of __constant_{endian}Harvey Harrison
The base versions handle constant folding now. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: fix srp sysfs entry deletionVikram Pandita
The SRP sysfs attribute is dependent on gadget mode; any gadget may support SRP. But "rmmod musb_hdrc" didn't remove that attribute; fix. Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Acked-by: Felipe Balbi <me@felipebalbi.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: resume suspended root hub on disconnectAnand Gadiyar
If this is not done, khubd will not be informed of the disconnect and will assume the device is still there. Easily seen when a hub is connected with no device attached to it; it will autosuspend. When the hub is disconnected, it still shows up in /proc/bus/usb/devices Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: use right poll limit for low speed devicesSergei Shtylyov
Remove wrongly applied upper limit on the interrupt transfer interval for low speed devices (not much of an error per se, according to USB specs). Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: be careful with 64K+ transfer lengths, host sideSergei Shtylyov
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO count in musb_host_tx() risks sending a short packet prematurely for transfer sizes over 64 KB. Similarly, although data transfer size shouldn't exceed 65535 bytes for the control endpoint, making musb_h_ep0_continue() more robust WRT URBs with possibly oversized buffer will not hurt either... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: fix data toggle saving with shared FIFOSergei Shtylyov
For some strange reason the host side musb_giveback() decides that it's always got an IN transfer when the hardware endpoint is using a shared FIFO. This causes musb_save_toggle() to read the toggle state from the RXCSR register instead of TXCSR, and may also cause unneeded reloading of RX endpoint registers. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: host endpoint_disable() oops fixesSergei Shtylyov
The musb_h_disable() routine can oops in some cases: - It's not safe to read hep->hcpriv outside musb->lock, since it gets changed on completion IRQ paths. - The list iterators aren't safe to use in that way; just remove the first element while !list_empty(), so deletions on other code paths can't make trouble. We need two "scrub the list" loops because only one branch should touch hardware and advance the schedule. [ dbrownell@users.sourceforge.net: massively simplify patch description; add key points as code comments ] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: fix urb_dequeue() methodSergei Shtylyov
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the control or bulk schedules when the URB being cancelled is the only one queued to its endpoint. That will cause musb_advance_schedule() to block once it reaches 'struct musb_qh' with now empty URB list, so URBs queued for other endpoints after the one being dequeued will not be served. Fix by unlinking the QH from the list except when it's already being handled (typically by musb_giveback). Since a QH with an empty URB list is now supposed to be freed, do that. And remove a now-useless check from musb_advance_schedule(). [ dbrownell@users.sourceforge.net: update patch description, and fold in a dequeue() comment patch ] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: fix musb_host_tx() for shared endpoint FIFODmitry Krivoschekov
The input queue should be used for TX on endpoints which share FIFO hardware. The host TX path wasn't doing that. Shared FIFOs are most often configured for periodic endpoints, which are mostly used for RX/IN transfers ... that's probably how this bug managed to linger for a long time. [ dbrownell@users.sourceforge.net: update patch description ] Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27USB: musb: be careful with 64K+ transfer lengths (gadget side)Felipe Balbi
request->actual is an unsigned and we should use the same variable type for fifo_count otherwise we might lose some data if request->length >= 64kbytes. [ dbrownell@users.sourceforge.net: fix compiler warning ] Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27usb: musb: make Davinci *work* in mainlineDavid Brownell
Now that the musb build fixes for DaVinci got merged (RC3?), kick in the other bits needed to get it finally *working* in mainline: - Use clk_enable()/clk_disable() ... the "always enable USB clocks" code this originally relied on has since been removed. - Initialize the USB device only after the relevant I2C GPIOs are available, so the host side can properly enable VBUS. - Tweak init sequencing to cope with mainline's relatively late init of the I2C system bus for power switches, transceivers, and so on. Sanity tested on DM6664 EVM for host and peripheral modes; that system won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also verified on OMAP3. (Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <me@felipebalbi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb: Kconfig fixDavid Brownell
The Blackfin MUSB Kconfig text didn't properly parenthesise its dependencies. This was visible in non-Blackfin configs by the way the user interfaces lost track of dependencies, when doing a bunch of test builds. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb cppi dma fixSwaminathan S
Initializes the actual_len field to 0 before every DMA transaction. Signed-off-by: Swaminathan S <swami.iyer@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb cppi bugfixesHugo Villeneuve
These compilation errors are related to incorrect debugging macro and variable names and generated the following errors: drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment': drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function) Signed-off-by: Hugo Villeneuve <hugo@hugovil.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb uses endpoint functionsJulia Lawall
This set of patches introduces calls to the following set of functions: usb_endpoint_dir_in(epd) usb_endpoint_dir_out(epd) usb_endpoint_is_bulk_in(epd) usb_endpoint_is_bulk_out(epd) usb_endpoint_is_int_in(epd) usb_endpoint_is_int_out(epd) usb_endpoint_num(epd) usb_endpoint_type(epd) usb_endpoint_xfer_bulk(epd) usb_endpoint_xfer_control(epd) usb_endpoint_xfer_int(epd) usb_endpoint_xfer_isoc(epd) In some cases, introducing one of these functions is not possible, and it just replaces an explicit integer value by one of the following constants: USB_ENDPOINT_XFER_BULK USB_ENDPOINT_XFER_CONTROL USB_ENDPOINT_XFER_INT USB_ENDPOINT_XFER_ISOC An extract of the semantic patch that makes these changes is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r1@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) == - \(USB_ENDPOINT_XFER_CONTROL\|0\)) + usb_endpoint_xfer_control(epd) @r5@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) == - \(USB_DIR_IN\|0x80\)) + usb_endpoint_dir_in(epd) @inc@ @@ #include <linux/usb.h> @depends on !inc && (r1||r5)@ @@ + #include <linux/usb.h> #include <linux/usb/...> // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb: tusb6010 buildfixKalle Valo
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h: No such file or directory drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h: No such file or directory Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb free_irq bugfixAjay Kumar Gupta
Fixes insert module failure as free_irq() was not done in previous rmmod. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb_hdrc: another davinci buildfix (otg related)David Brownell
The DaVinci code had an implementation of the OTG transceiver glue too; make it use the new-standard one. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: musb davinci buildfixDavid Brownell
Trying once more to get this merged. The original was submitted for 2.6.27-rc2 or so, and never got correctly merged. Neither were any of the numerous subsequent resends. Sigh. CC drivers/usb/musb/davinci.o drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode' drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07USB: musb: Kill some compiling warning in musb Blackfin partBryan Wu
Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07USB: musb: Blackfin provides read/write I/O accessor in header filesBryan Wu
Don't redefine the functions in musb driver Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07USB: musb: add Blackfin Kconfig options and MakefileBryan Wu
Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>