Age | Commit message (Collapse) | Author |
|
mach-gta02 meddles with the regulator platform struct after
it is defined, leading to LCM power getting lost in suspend
despite I set it to be left up. Fixing this finally removes
the incredibly stubborn white LCM on suspend "flash".
This is also going to be implicated in Sean McNeil's
experience of monochromatic LCM after resume, which was
previously attacked by resetting and re-initing the LCM
from scratch.
In addition, I realized that we take down core_1v3 in
pcf50633 suspend action, this is happening near the
start of suspend, so we are in a meta-race to finish
suspend in a controlled way before the caps on core_1v3
run out (I only saw 23.3uF total). If it's true, this
is where the weirdo sensitivity to timing during
suspend is coming from.
Therefore in this patch we also remove sleeps and
dev_info() etc (which have to flush on serial console)
from the pc50633 isr workqueue if we are in pcf50633
driver suspend state 1, ie, suspending... because we
don't have time for it.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
The LCM spins for 100ms during resume for not much reason. Leave it powered
(it is meant to pull uA when suspended) and get nice fast resume to video.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Sean McNeil reports that without the reset for LCM in suspend, he
gets a monochromatic mode on it somehow.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Adds the resume callback stuff to glamo, then changes
jbt6k74 to no longer use a sleeping workqueue, but to
make its resume actions dependent on pcf50633 and
glamo resume (for backlight and communication to LCM
respectively)
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This patch improves the smoothness of suspend and resume action.
Taking out CONFIG_PM_DEBUG allows much more rapid resume (the low level
serial traffic appears to be synchronous)
Added a platform callback in jbt driver and support in pcf50633 so we
can defer bringing up the backlight until the LCM is able to process
video again (which must happen after the glamo is up and producing
video beacuse the LCM is hooked to glamo SPI)
GTA01 should not be affected by all this as the callback will default
to null and it is on pcf50606
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-Off-By: Holger Freyther <zecke@openmoko.org>
|
|
|
|
This driver adds support for the SPI-based control interface of the LCM (LCD
Panel) found on the FIC GTA01 hardware.
The specific panel in this hardware is a TPO TD028TTEC1, but the driver should
be able to drive any other diplay based on the JBT6K74-AS controller ASIC.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
Now that device_create() has been audited, rename things back to the
original call to be sane.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the new display class. This is meant to unite the various solutions to
display units ie acpi output device, auxdisplay and the defunct lcd class
in the backlight directory.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|