aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2007-07-18[SCSI] a4000t, zorro7xx, mvme16x, bvme6000,sim710: xxx_device_remove seems buggyMatthew Wilcox
Fix drivers misusing dev_to_shost Some drivers were using dev_to_shost to go from a struct device to the corresponding shost. Unfortunately, dev_to_shost only looks up the tree to find an shost (it's designed to go from a scsi_device or a scsi_target to the parent scsi_host), and these drivers were calling it with the parent of the scsi_host. I've fixed this by saving a pointer to the Scsi_Host in the drvdata, which matches what most scsi drivers do. Signed-off-by: Matthew Wilcox <matthew@wil.cx> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] aacraid: add vpd to inquirySalyzyn, Mark
Report VPD inquiry page 0x80 with an unique array creation serial number (CUID). When an array is created, the metadata stored on the physical drives gets an unique serial number. This serial number remains constant through array morphing or migration to other controllers. This patch is a forward port and modification to survive morphing and migration operations, of a similar piece of (un-attributed author) code added to the SLES10 SP1 aacraid driver. To test the results of the patch, observe that /dev/disk/by-id/ entries will show up for the arrays resulting from the udev rules. Also, as per the udev rules, 'scsi_id -g -x -a -s /block/sd? -d /dev/sd?' will report the ID_SERIAL as constructed from the inquiry data. It was reported to me that the 'ADPT' leading the serial number was bad form, that the inquiry vendor field was enough to differentiate the storage uniquely. Subsequent search found that another Adaptec AAC based driver reported the 8 hex serial number only without such adornments, so dropped ADPT to match. Resubmitting the patch with this alteration. Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] aacraid: incorrect dma mapping mask during blinkled recover or user ↵Salyzyn, Mark
initiated reset Incorrect dma mask was used for blinkled (firmware assert) recovery or user initiated reset during initialization portion. Ensure that all callers of aac_fib_map_free null out the fib allocation references to prevent multiple free. Although serious sounding, no reports of these problems have surfaced... Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] aacraid: correct valid container response in management ioctlSalyzyn, Mark
During an Adapter Initiated scan request, the query disk ioctl reports a value of 2 rather than 1 for the valid field. This presents a problem for some legacy management applications. Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] mpt fusion: add support for Brocade branded LSI FC HBAPrakash, Sathya
Add support for Brocade 410/420 4Gbit FC HBAs. They are re-branded LSI HBAs [LSI7104EP-LC/LSI7204EP-LC] Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com> Acked-by: "Moore, Eric" <Eric.Moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] mpt fusion: deregister from transport layer if PCI registration failedPrakash, Sathya
The mptspi and mptsas drivers are modified to deregister from transport layer if registration with PCI driver failed Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] mpt fusion: add sysfs attributes to display IOC parametersPrakash, Sathya
New sysfs scsi_host attributes are added to provide information about Firmware version, BIOS version, MPI version and other product related information signed-off-by: Sathya Praksh <sathya.prakash@lsi.com> Acked-by: "Moore, Eric" <Eric.Moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] Use menuconfig objectsJan Engelhardt
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that the user can disable all the options in that menu at once instead of having to disable each option separately. Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] seagate: make seagate_st0x_detect() staticAdrian Bunk
seagate_st0x_detect() can become static. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] wd33c93: cleanupsAdrian Bunk
- #include <asm/irq.h> for getting the prototypes of {dis,en}able_irq() - make the needlessly global wd33c93_setup() static Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] small cleanupsAdrian Bunk
This patch contains the following cleanups: - make needlessly global functions static - every file should #include the headers containing the prototypes for it's global functions Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: fix lockdep issue with ATAJames Bottomley
lockdep noticed that with ATA support the port->dev_list_lock was entangled at irq context, so it now needs to become IRQ safe Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas, aic94xx: fix dma mapping cockups with ATAJames Bottomley
This one was noticed by Gilbert Wu of Adaptec: The libata core actually does the DMA mapping for you, so there has to be an exception in the device drivers that *don't* do dma mapping for ATA commands. However, since we've already done this, libsas must now dma map any ATA commands that it wishes to issue ... and yes, this is a horrible mess. Additionally, the test in aic94xx for ATA protocols isn't quite right. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] sas_ata: Implement sas_task_abort for ATA devicesDarrick J. Wong
ATA devices need special handling for sas_task_abort. If the ATA command came from SCSI, then we merely need to tell SCSI to abort the scsi_cmnd. However, internal commands require a bit more work--we need to fill the qc with the appropriate error status and complete the command, and eventually post_internal will issue the actual ABORT TASK. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] sas_ata: Assign sas_task to scsi_cmnd to enable EH for ATA devicesDarrick J. Wong
The SATL should connect the scsi_cmnd to the sas_task (despite the presence of libata) so that requests to abort scsi_cmnds headed to the ATA device can be processed by the EH and aborted correctly. The abort status should still be propagated from sas -> ata -> scsi. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: Unknown STP devices should be reported to libata as unknown.Darrick J. Wong
When libsas encounters a STP device whose protocol isn't recognized (i.e. not ATA or ATAPI), we should set the ata_device's class to ATA_DEV_UNKNOWN instead of ATA_DEV_ATA. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: Accept SAM_GOOD for ATAPI devices in sas_ata_task_doneDarrick J. Wong
A sas_task sent to an ATAPI devices returns SAM_GOOD if successful. Therefore, we should treat this the same way we treat ATA commands that succeed. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] sas_ata: Don't copy aic94xx's sactive to ata_portDarrick J. Wong
Since the aic94xx sequencer assigns its own NCQ tags to ATA commands, it no longer makes any sense to copy the sactive field in the STP response to ata_port->sactive, as that will confuse libata. Also, libata seems to be capable of managing sactive on its own. The attached patch gets rid of one of the causes of the BUG messages in ata_qc_new, and seems to work without problems on an IBM x206m. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] sas_ata: ata_post_internal should abort the sas_taskDarrick J. Wong
This patch adds a new field, lldd_task, to ata_queued_cmd so that libata users such as libsas can associate some data with a qc. The particular ambition with this patch is to associate a sas_task with a qc; that way, if libata decides to timeout a command, we can come back (in sas_ata_post_internal) and abort the sas task. One question remains: Is it necessary to reset the phy on error, or will the libata error handler take care of it? (Assuming that one is written, of course.) This patch, as it is today, works well enough to clean things up when an ATA device probe attempt fails halfway through the probe, though I'm not sure this is always the right thing to do. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] sas_ata: sas_ata_qc_issue should return AC_ERR_*Darrick J. Wong
The sas_ata_qc_issue function was incorrectly written to return error codes such as -ENOMEM. Since libata OR's qc->err_mask with the return value, It is necessary to make my code return one of the AC_ERR_ codes instead. For now, use AC_ERR_SYSTEM because an error here means that the OS couldn't send the command to the controller. If anybody has a suggestion for a better AC_ERR_ code to use, please suggest it. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] sas_ata: Satisfy libata qc function locking requirementsDarrick J. Wong
ata_qc_complete and ata_sas_queuecmd require that the port lock be held when they are called. sas_ata doesn't do this, leading to BUG messages about qc tags newly allocated qc tags already being in use. This patch fixes the locking, which should clean up the rest of those messages. So far I've tested this against an IBM x206m with two SATA disks with no BUG messages and no other signs of things going wrong, and the machine finally passed the pounder stress test. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] aic94xx: Don't call pci_map_sg for already-mapped scatterlistsDarrick J. Wong
It turns out that libata has already dma_map_sg'd the scatterlist entries that go with an ata_queued_cmd by the time it calls sas_ata_qc_issue. sas_ata_qc_issue passes this scatterlist to aic94xx. Unfortunately, aic94xx assumes that any scatterlist passed to it needs to be pci_map_sg'd... which blows away the mapping that libata created! This causes (on a x260) Calgary IOMMU table leaks and duplicate frees when aic94xx and libata try to {pci,dma}_unmap_sg the scatterlist. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Key this check off ATA_PROTOCOL_STP Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] Migrate libsas ATA code into a separate fileDarrick J. Wong
This is a respin of my earlier patch that migrates the ATA support code into a separate file. For now, the controversial linking bits have been removed per James Bottomley's request for a patch that contains only the migration diffs, which means that libsas continues to require libata. I intend to address that problem in a separate patch. This patch is against the aic94xx-sas-2.6 git tree, and it has been sanity tested on my x206m with Seagate SATA and SAS disks without uncovering any new problems. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: fixup NCQ for SATA disksJames Bottomley
We actually had two problems: the one with the tag (which is fixed by zeroing the tag before sending the taskfile to the sequencer) but the other with the fact that we sent our first NCQ command to the device before the sequencer had been informed of the NCQ tagging capabilities. I fixed the latter by moving the rphy_add() to the correct point in the code after the NCQ capabilities are set up. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: better error handling in sas_ex_discover_end_dev()James Bottomley
This replaces a few BUG_ON() statements with the correct failure error handling. There are still many more to do. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] aic94xx: add SATAPI supportJames Bottomley
It turns out this is fairly easy to plumb in by recognising the three command types and copying the CDB. The protocol response path needs to be amended to cope with SAS_PROTO_RESPONSE. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: support NCQ for SATA disksDarrick J. Wong
This patch adds SATAII NCQ support to libsas. Both the use_ncq and the dma_xfer flags in ata_task must be set for NCQ to work correctly on the Adaptec SAS controller. The rest of the patch adds ATA_FLAG_NCQ to sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't crash. Please note that this patch is against the aic94xx-sas git tree, not scsi-misc. Thanks also to James Bottomley for providing an earlier version of this patch from which to work. I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged into the Adaptec SAS controller. The drive came up with a queue depth of 31, and I successfully ran an I/O flood test to coerce libata into sending multiple commands simultaneously. A kernel probe recorded the maximum tag number that had been seen before and after the flood test; before the test it was 2 and after it was 30, as I expected. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] aic94xx: SATA tag mask not set correctlyDarrick J. Wong
The aic94xx controller has a bitmask establishing which tags are ok to use with a SATA NCQ disk. When the queue depth is 32, however, the expression that is used sets the mask to zero, not 0xFFFFFFFF. This patch widens the width of the integer so that this case is handled properly. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: fix up sas_smp_phy_control()James Bottomley
The prototype of this has changed for the link speed setting patch. Need to update the SATA use of this. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] libsas: Add SATA support to STP piece for SATA on SAS expandersJames Bottomley
This patch adds support for SATA over SAS expanders to the previous two SATA support in libsas patches. There were a couple of nasty non trivial things to sort out before this one could be made to work. Firstly, I'd like to thank Doug Gilbert for diagnosing a problem with the LSI expanders where the REPORT_SATA_PHY command was returning the D2H FIS in the wrong order (Although, here, I think I have to blame the SAS standards which specifies the FIS "shall be returned in little endian format" and later on "which means resp[24] shall be FIS type" The latter, of course, implying big endian format). Just to make sure, I put a check for the D2H FIS type being in the wrong position and reverse the FIS data if it is. The second is a problem outlined in Annex G of the SAS standard (again, a technical point with D2H FIS ... necessitating a phy reset on certain conditions). With the patch, I can now see my SATA-1 disk in a cascaded expander configuration. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18[SCSI] Add SATA support to libsasDarrick J. Wong
Hook the scsi_host_template functions in libsas to delegate functionality to libata when appropriate. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Misc code changes and merge fixes and update for libata->drivers/ata move Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-18zs: move to the serial subsystemMaciej W. Rozycki
This is a reimplementation of the zs driver for the serial subsystem. Any resemblance to the old driver is purely coincidential. ;-) I do hope I got the handling of modem lines right -- better do not tackle me about the issue unless you feel too good... Any users of the old driver: please note the numbers of the serial lines have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has to do with the modem lines mentioned above; basically the port A in a given chip has to be initialised before the port B if you want to use the latter as the serial console (which is usually the case), as operations on modem lines of the serial line associated with the port B access both ports (see the comment at the top of the driver for the details of wiring used). Please update your scripts. This is also the reason each SCC now requests an IRQ once only (as seen in "/proc/interrupts") -- the handler takes care of both ports at once as the line associated with the port B has to take status update interrupts from both ports (and yet the line of the port A takes its own for itself too). The old driver never got it right... Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-18serial: add early_serial_setup() back to header fileYinghai Lu
early_serial_setup was removed from serial.h, but forgot to put in serial_8250.h Signed-off-by: Yinghai Lu <yinghai.lu@sun.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-18fbdev: make fb_append_extra_logo() depend on fb=yArnd Bergmann
We can't show the extra logo from boot code if FB is built as a module. Make the FB_LOGO_EXTRA depend on FB=y. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Antonino A. Daplas" <adaplas@pol.net> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-18dm: fix memory leak in dm_create_persistent() when starting metadata update ↵Jesper Juhl
thread fails If, in dm_create_persistent(), the call to create_singlethread_workqueue() fails then we'll return without freeing the memory allocated to 'ps', thus leaking sizeof(struct pstore) bytes. This patch fixes the leak. Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com Acked-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17Revert drivers/ide/ide.c scsi_cmd_ioctl() usage changesLinus Torvalds
The old IDE driver is not ready to take generic SCSI commands, even if it uses them for some specific issues (ie the tray open/close ioctls for IDE CD-ROM's). Pointed out by Bartlomiej. I'm sure we'll have it fixed properly soon enough, but for now we should not allow it to cause problems. Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17Make the "z/VM unit record device driver" depend on S390Linus Torvalds
I really don't see anybody else wanting to select it ;) Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6Linus Torvalds
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: [S390] Fix broken logic, SIGA flags must be bitwise ORed [S390] cio: Dont print trailing \0 in modalias_show(). [S390] Simplify stack trace. [S390] z/VM unit record device driver [S390] vmcp cleanup [S390] qdio: output queue stall on FCP and network devices [S390] Fix disassembly of RX_URRD, SI_URD & PC-relative instructions. [S390] Update default configuration.
2007-07-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdogLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (21 commits) [WATCHDOG] at32ap700x_wdt.c - Fix compilation warnings [WATCHDOG] at32ap700x_wdt.c - Add spinlock support [WATCHDOG] at32ap700x_wdt.c - Add nowayout + MAGICCLOSE features [WATCHDOG] at32ap700x_wdt.c - timeout module parameter patch [WATCHDOG] at32ap700x_wdt.c - checkpatch.pl-0.05 clean-up's [WATCHDOG] change s3c2410_wdt to using dev_() macros for output [WATCHDOG] s3c2410_wdt announce initialisation [WATCHDOG] at32ap700x-wdt: add iounmap if probe function fails [WATCHDOG] at32ap700x-wdt: add missing iounmap in _remove [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix-2 [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix [WATCHDOG] Watchdog driver for AT32AP700X devices [WATCHDOG] Mixcom Watchdog - CodingStyle clean-up [WATCHDOG] Mixcom Watchdog - clean-up printk's [WATCHDOG] Mixcom Watchdog - clean-up printk's [WATCHDOG] Mixcom Watchdog - checkcard part 2 [WATCHDOG] Mixcom Watchdog - checkcard [WATCHDOG] Mixcom Watchdog - get rid of port offset's [WATCHDOG] Mixcom Watchdog - update "Documentation" [WATCHDOG] Remove the redundant check for pwrite() in EP93XXX watchdog. ...
2007-07-17Merge branch 'isdn-cleanup' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6 * 'isdn-cleanup' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6: [ISDN] HiSax hfc_pci: minor cleanups [ISDN] HiSax bkm_a4t: split setup into two smaller functions [ISDN] HiSax enternow: split setup into 3 smaller functions [ISDN] HiSax netjet_u: split setup into 3 smaller functions [ISDN] HiSax netjet_s: code movement, prep for hotplug [ISDN] HiSax: move card state alloc/setup code into separate functions [ISDN] HiSax: move card setup into separate function
2007-07-17Merge branch 'uninit-var' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6 * 'uninit-var' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6: arch/i386/* fs/* ipc/*: mark variables with uninitialized_var() drivers/*: mark variables with uninitialized_var()
2007-07-17Merge branch 'warnings' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6 * 'warnings' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6: drivers/atm/ambassador: kill uninit'd var warning, and fix bug [libata] sata_mv: use pci_try_set_mwi() drivers/infiniband/hw/mthca/mthca_qp: kill uninit'd var warning drivers/net/wan/sbni: kill uninit'd var warning drivers/mtd/ubi/eba: minor cleanup: tighten scope of a local var drivers/telephony/ixj: cleanup and fix gcc warning drivers/net/wan/pc300_drv: fix bug caught by gcc warning drivers/usb/misc/auerswald: fix status check, remove redundant check [netdrvr] eepro100, ne2k-pci: abort resume if pci_enable_device() fails [netdrvr] natsemi: Fix device removal bug kernel/auditfilter: kill bogus uninit'd-var compiler warning
2007-07-17[ISDN] HiSax hfc_pci: minor cleanupsJeff Garzik
* trim trailing whitespace * remove CONFIG_PCI ifdefs, this driver is always PCI (Kconfig enforced) * remove return statements at the tail of a function * remove indentation levels by returning an error code immediately. Makes the code much more readable, and easier to update to PCI hotplug API. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17[ISDN] HiSax bkm_a4t: split setup into two smaller functionsJeff Garzik
No behavior changes, just code movement. Prep for PCI hotplug API. Well, CONFIG_PCI useless ifdef was removed. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17[ISDN] HiSax enternow: split setup into 3 smaller functionsJeff Garzik
No behavior changes, just code movement. Prep for PCI hotplug API. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17[ISDN] HiSax netjet_u: split setup into 3 smaller functionsJeff Garzik
No behavior changes, just code movement. Prep for PCI hotplug API. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17[ISDN] HiSax netjet_s: code movement, prep for hotplugJeff Garzik
1) Remove CONFIG_PCI ifdefs. PCI is required in Kconfig. 2) Break up setup_netjet_s() into three separate internal functions. This helps facilitate upcoming use of PCI hotplug API, and in addition makes the code much easier to follow. No code is changed, just moved around. I even kept the out-of-favor "return(0)" style used in the current source code. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17[ISDN] HiSax: move card state alloc/setup code into separate functionsJeff Garzik
Just code movement. No code changes or cleanups besides that which is required to call the new functions from the old code site. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17[ISDN] HiSax: move card setup into separate functionJeff Garzik
No behavior changes, just code movement. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17hppb: Add missing dma-mapping.h includeFrank Lichtenheld
This fixes the following build-error: CC drivers/parisc/hppb.o drivers/parisc/hppb.c: In function ‘hppb_probe’: drivers/parisc/hppb.c:73: error: implicit declaration of function ‘ccio_request_resource’ Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>