| Age | Commit message (Collapse) | Author |
|---|
|
Fix sizing of big_bytes in the case of vlan frames. The 4
VLAN_HLEN bytes were omitted, leading to sizing the big buffer
4 bytes smaller than it should be. Due to how rx buffers are
carved from pages, this was harmless for the common (9000, 1500)
byte MTUs, but could lead to data corruption for some MTUs.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Receive full vlan frames into smalls when running with a jumbo MTU.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Drop the old routines that used the physically contigous skb now
that we use the physical pages. And rename myri10ge_page_rx_done()
to myri10ge_rx_done() as it was previously.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Switch to physical page skb, by calling the new page-based
allocation routines and using myri10ge_page_rx_done().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add physical page skb allocation routines and page based rx_done,
to be used by upcoming patches.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Indentation cleanups to synchronize to our tree which is automatically
indent'ed.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This driver tries to enable/disable NAPI at runtime, but
does so in an unsafe manner, and the NAPI interrupt handling is
a mess. Replace it with a compile time selected NAPI implementation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Since macb is a chip-internal device, use __raw_readl and
__raw_writel instead of readl/writel. This will perform native-endian
accesses, which is the right thing to do on both AVR32 and ARM devices.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The macb driver calls schedule_delayed_work() and friends, so we need
to use a struct delayed_work along with it. The conversion was
explained by David Howells on lkml Dec 5 2006:
http://lkml.org/lkml/2006/12/5/269
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix compilation failures when building the ucc_geth driver with spinlock
debugging.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
As CBC is the default chaining method for cryptoloop, we should select
it from cryptoloop to ease the transition. Spotted by Rene Herman.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (132 commits)
V4L/DVB 4949b: Fix container_of pointer retreival
V4L/DVB (4949a): Fix INIT_WORK
V4L/DVB (4949): Cxusb: codingstyle cleanups
V4L/DVB (4948): Cxusb: Convert tuner functions to use dvb_pll_attach
V4L/DVB (4947): Cx88: trivial cleanups
V4L/DVB (4946): Cx88: Move cx88_dvb_bus_ctrl out of the card-specific area
V4L/DVB (4945): Cx88: consolidate cx22702_config structs
V4L/DVB (4944): Cx88: Convert DViCO FusionHDTV Hybrid to use dvb_pll_attach
V4L/DVB (4943): Cx88: cleanup dvb_pll_attach for lgdt3302 tuners
V4L/DVB (4953): Usbvision minor fixes
V4L/DVB (4951): Add version.h, since it is required for VIDIOC_QUERYCAP
V4L/DVB (4940): Or51211: Changed SNR and signal strength calculations
V4L/DVB (4939): Or51132: Changed SNR and signal strength reporting
V4L/DVB (4938): Cx88: Convert lgdt3302 tuning function to use dvb_pll_attach
V4L/DVB (4941): Remove LINUX_VERSION_CODE and fix identations
V4L/DVB (4942): Whitespace cleanups
V4L/DVB (4937): Usbvision cleanup and code reorganization
V4L/DVB (4936): Make MT4049FM5 tuner to set FM Gain to Normal
V4L/DVB (4935): Added the capability of selecting fm gain by tuner
V4L/DVB (4934): Usbvision radio requires GainNormal at e register
...
|
|
web site: http://kvm.sourceforge.net
mailing list: kvm-devel@lists.sourceforge.net
(http://lists.sourceforge.net/lists/listinfo/kvm-devel)
The following patchset adds a driver for Intel's hardware virtualization
extensions to the x86 architecture. The driver adds a character device
(/dev/kvm) that exposes the virtualization capabilities to userspace. Using
this driver, a process can run a virtual machine (a "guest") in a fully
virtualized PC containing its own virtual hard disks, network adapters, and
display.
Using this driver, one can start multiple virtual machines on a host.
Each virtual machine is a process on the host; a virtual cpu is a thread in
that process. kill(1), nice(1), top(1) work as expected. In effect, the
driver adds a third execution mode to the existing two: we now have kernel
mode, user mode, and guest mode. Guest mode has its own address space mapping
guest physical memory (which is accessible to user mode by mmap()ing
/dev/kvm). Guest mode has no access to any I/O devices; any such access is
intercepted and directed to user mode for emulation.
The driver supports i386 and x86_64 hosts and guests. All combinations are
allowed except x86_64 guest on i386 host. For i386 guests and hosts, both pae
and non-pae paging modes are supported.
SMP hosts and UP guests are supported. At the moment only Intel
hardware is supported, but AMD virtualization support is being worked on.
Performance currently is non-stellar due to the naive implementation of the
mmu virtualization, which throws away most of the shadow page table entries
every context switch. We plan to address this in two ways:
- cache shadow page tables across tlb flushes
- wait until AMD and Intel release processors with nested page tables
Currently a virtual desktop is responsive but consumes a lot of CPU. Under
Windows I tried playing pinball and watching a few flash movies; with a recent
CPU one can hardly feel the virtualization. Linux/X is slower, probably due
to X being in a separate process.
In addition to the driver, you need a slightly modified qemu to provide I/O
device emulation and the BIOS.
Caveats (akpm: might no longer be true):
- The Windows install currently bluescreens due to a problem with the
virtual APIC. We are working on a fix. A temporary workaround is to
use an existing image or install through qemu
- Windows 64-bit does not work. That's also true for qemu, so it's
probably a problem with the device model.
[bero@arklinux.org: build fix]
[simon.kagstrom@bth.se: build fix, other fixes]
[uril@qumranet.com: KVM: Expose interrupt bitmap]
[akpm@osdl.org: i386 build fix]
[mingo@elte.hu: i386 fixes]
[rdreier@cisco.com: add log levels to all printks]
[randy.dunlap@oracle.com: Fix sparse NULL and C99 struct init warnings]
[anthony@codemonkey.ws: KVM: AMD SVM: 32-bit host support]
Signed-off-by: Yaniv Kamay <yaniv@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Simon Kagstrom <simon.kagstrom@bth.se>
Cc: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Uri Lublin <uril@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Mostly changing alignment. Just some general cleanup.
[akpm@osdl.org: build fix]
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix few bugs that meant that:
- superblocks weren't alway written at exactly the right time (this
could show up if the array was not written to - writting to the array
causes lots of superblock updates and so hides these errors).
- restarting device recovery after a clean shutdown (version-1 metadata
only) didn't work as intended (or at all).
1/ Ensure superblock is updated when a new device is added.
2/ Remove an inappropriate test on MD_RECOVERY_SYNC in md_do_sync.
The body of this if takes one of two branches depending on whether
MD_RECOVERY_SYNC is set, so testing it in the clause of the if
is wrong.
3/ Flag superblock for updating after a resync/recovery finishes.
4/ If we find the neeed to restart a recovery in the middle (version-1
metadata only) make sure a full recovery (not just as guided by
bitmaps) does get done.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently raid5 depends on clearing the BIO_UPTODATE flag to signal an error
to higher levels. While this should be sufficient, it is safer to explicitly
set the error code as well - less room for confusion.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There are some vestiges of old code that was used for bypassing the stripe
cache on reads in raid5.c. This was never updated after the change from
buffer_heads to bios, but was left as a reminder.
That functionality has nowe been implemented in a completely different way, so
the old code can go.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The autorun code is only used if this module is built into the static
kernel image. Adjust #ifdefs accordingly.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
stripe_to_pdidx finds the index of the parity disk for a given stripe. It
assumes raid5 in that it uses "disks-1" to determine the number of data disks.
This is incorrect for raid6 but fortunately the two usages cancel each other
out. The only way that 'data_disks' affects the calculation of pd_idx in
raid5_compute_sector is when it is divided into the sector number. But as
that sector number is calculated by multiplying in the wrong value of
'data_disks' the division produces the right value.
So it is innocuous but needs to be fixed.
Also change the calculation of raid_disks in compute_blocknr to make it
more obviously correct (it seems at first to always use disks-1 too).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Call the chunk_aligned_read where appropriate.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If a bypass-the-cache read fails, we simply try again through the cache. If
it fails again it will trigger normal recovery precedures.
update 1:
From: NeilBrown <neilb@suse.de>
1/
chunk_aligned_read and retry_aligned_read assume that
data_disks == raid_disks - 1
which is not true for raid6.
So when an aligned read request bypasses the cache, we can get the wrong data.
2/ The cloned bio is being used-after-free in raid5_align_endio
(to test BIO_UPTODATE).
3/ We forgot to add rdev->data_offset when submitting
a bio for aligned-read
4/ clone_bio calls blk_recount_segments and then we change bi_bdev,
so we need to invalidate the segment counts.
5/ We don't de-reference the rdev when the read completes.
This means we need to record the rdev to so it is still
available in the end_io routine. Fortunately
bi_next in the original bio is unused at this point so
we can stuff it in there.
6/ We leak a cloned bio if the target rdev is not usable.
From: NeilBrown <neilb@suse.de>
update 2:
1/ When aligned requests fail (read error) they need to be retried
via the normal method (stripe cache). As we cannot be sure that
we can process a single read in one go (we may not be able to
allocate all the stripes needed) we store a bio-being-retried
and a list of bioes-that-still-need-to-be-retried.
When find a bio that needs to be retried, we should add it to
the list, not to single-bio...
2/ We were never incrementing 'scnt' when resubmitting failed
aligned requests.
[akpm@osdl.org: build fix]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This will encourage read request to be on only one device, so we will often be
able to bypass the cache for read requests.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
An md array can be stopped leaving all the setting still in place, or it can
torn down and destroyed. set_capacity and other change notifications only
happen in the latter case, but should happen in both.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This is an fbdev driver for the IBM GXT4500P display card found in some IBM
System P (pSeries) machines. These cards have hardware 2D and 3D
capabilities, but the driver does not use them; it just exports a dumb
framebuffer.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The ESB2 appears to emit spurious DMA interrupts when configured for native
mode and handling ATAPI devices. Stratus were able to pin this bug down and
produce a patch. This is a rework which applies the fixup only to the ESB2
(for now). We can apply it to other chips later if the same problem is found.
This code has been tested and confirmed to fix the problem on the tested
systems.
Signed-off-by: Alan Cox <alan@redhat.com>
(Most of the hard work done by Stratus however)
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix the CRC errors in the higher UltraDMA modes with the Promise PDC20268
and newer chips that always occur on non-x86 machines and when there are
more than 2 adapters on x86 machines. Fix the overclocking issue for
PDC20269 and newer chips that occurs when an UltraDMA/133 capable drive is
connected. Here's the summary of changes:
- add code to detect the PLL input clock detection and setup it output clock,
remove the PowerMac hacks;
- replace the macros accessing the indexed regiters with functions, switch to
using them where appropriate, gather the PIO/MWDMA/UDMA timings into tables;
- rewrite the speedproc() handler to set the drive's transfer mode first, and
then override the timing registers set by hardware on UltraDMA/133 chips;
- use better criterion for determining higher UltraDMA modes, and add comment
concerning the doubtful value of the code enabling IORDY/prefetch;
- replace the stupid 'pdcnew_new_' prefixes with mere 'pdcnew_';
- get rid of unneded spaces, parens and type casts, clean up some printk's,
add some new lines here and there...
This work is loosely based on these former patches by Albert Lee:
[1] http://marc.theaimsgroup.com/?l=linux-ide&m=110992442032300
[2] http://marc.theaimsgroup.com/?l=linux-ide&m=110992457729382
[3] http://marc.theaimsgroup.com/?l=linux-ide&m=110992474205555
[4] http://marc.theaimsgroup.com/?l=linux-ide&m=111019224802939
Some PLL clock detection code was backported from his pata_pdc2027x driver...
This code has been successfully tested by me on PDC2026[89] chips.
I tried to keep this rework as several patches but it made no sense: [2] was
largely a modification of the non-working timing override code, [3] by itself
extended the overclocking issue to the case of non-UltraDMA/133 drives, and
finally, the cleanup patch based on [1] ended up rejected...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Albert Lee <albertcc@tw.ibm.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix various problems pointed out by Andrew Morton and others:
* platform_device_unregister checks for NULL, no need to check here.
* Formatting fixes.
* Remove big macro and convert to a function.
* Use strcmp instead of defining a broken case-insensitive comparison,
and make the output parameter info match the case of the input one
(change "I/O" to "i/o").
* Return the length instead of 0 from the hotmod parameter handler.
* Remove some unused cruft.
* The trydefaults parameter only has to do with scanning the "standard"
addresses, don't check for that on ACPI.
Signed-off-by: Corey Minyard <cminyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove all =0 and =NULL from static initializers. They are not needed and
removing them saves space in the object files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The new Atmel AT91SAM9261 and AT91SAM9260 processors do not have the
internal RTC peripheral. This RTC driver is therefore
AT91RM9200-specific.
This patch renames rtc-at91.c to rtc-at91rm9200.c, and changes the name
of the configuration option.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Update more I2C drivers that live outside drivers/i2c to understand that using
adapter->dev is not The Way. When actually referring to the adapter hardware,
adapter->class_dev.dev is the answer. When referring to a device connected to
it, client->dev.dev is the answer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add rtc_merge_alarm(), which can be used by rtc drivers to turn a partially
specified alarm expiry (i.e. most significant fields set to -1, as with the
RTC_ALM_SET ioctl()) into a fully specified expiry.
If the most significant specified field is earlier than the current time, the
least significant unspecified field is incremented.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This driver seems to be for a PCI device.
drivers/crypto/geode-aes.c:384: warning: implicit declaration of function 'pci_release_regions'
drivers/crypto/geode-aes.c:397: warning: implicit declaration of function 'pci_request_regions'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Stabilize PIO mode transfers against a range of word sizes and FIFO
thresholds and fixes word size setup/override issues.
1) 16 and 32 bit DMA/PIO transfers broken due to timing differences.
2) Potential for bad transfer counts due to transfer size assumptions.
3) Setup function broken is multiple ways.
4) Per transfer bit_per_word changes break DMA setup in pump_tranfers.
5) False positive timeout are not errors.
6) Changes in pxa2xx_spi_chip not effective in calls to setup.
7) Timeout scaling wrong for PXA255 NSSP.
8) Driver leaks memory while busy during unloading.
Known issues:
SPI_CS_HIGH and SPI_LSB_FIRST settings in struct spi_device are not handled.
Testing:
This patch has been test against the "random length, random bits/word,
random data (verified on loopback) and stepped baud rate by octaves
(3.6MHz to 115kHz)" test. It is robust in PIO mode, using any
combination of tx and rx thresholds, and also in DMA mode (which
internally computes the thresholds).
Much thanks to Ned Forrester for exhaustive reviews, fixes and testing.
The driver is substantially better for his efforts.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The reverse get function allows the final piece of the switching for the old
IDE layer
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Ramiro Voicu hits the BUG_ON(!pte_none(*pte)) in zeromap_pte_range: kernel
bugzilla 7645. Right: read_zero_pagealigned uses down_read of mmap_sem,
but another thread's racing read of /dev/zero, or a normal fault, can
easily set that pte again, in between zap_page_range and zeromap_page_range
getting there. It's been wrong ever since 2.4.3.
The simple fix is to use down_write instead, but that would serialize reads
of /dev/zero more than at present: perhaps some app would be badly
affected. So instead let zeromap_page_range return the error instead of
BUG_ON, and read_zero_pagealigned break to the slower clear_user loop in
that case - there's no need to optimize for it.
Use -EEXIST for when a pte is found: BUG_ON in mmap_zero (the other user of
zeromap_page_range), though it really isn't interesting there. And since
mmap_zero wants -EAGAIN for out-of-memory, the zeromaps better return that
than -ENOMEM.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Ramiro Voicu: <Ramiro.Voicu@cern.ch>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Refactor Kconfig content to maximize nesting of menus by menuconfig and
xconfig.
Tested by simultaneously running `make xconfig` with and without
patch, and comparing displays.
Signed-off-by: Don Mullis <dwm@meer.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This driver is an AC97 codec according to its help text. However, if SOUND is
disabled, the "select SND_AC97_BUS" still inserts that into the .config file:
#
# Sound
#
# CONFIG_SOUND is not set
CONFIG_SND_AC97_BUS=m
Even if the config software followed dependency chains on selects, we should
try to limit usage of "select" to library-type code that is needed (e.g., CRC
functions) instead of bus-type support.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
INIT_WORK syntax changed on kernel 2.6.19. Fixing it on
usbvision and cx88-input.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Trivial whitespace / 80-column limit cleanups
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Converted dee1601, lgz201 and dtt8579 to use dvb_pll_attach
in dvb-usb-cxusb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- small whitespace cleanups
- 80-column whitespace cleanups
- remove unneeded brackets
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This function should not be in the card-specific area of the file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There are five cx22702_config structs used by cx88-dvb, only two of which
are unique. This patch removes the duplicates and sets each card to use
one of the two remaining config structs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Converted DViCO FusionHDTV Hybrid to use dvb_pll_attach, removing
another static dependency of cx88-dvb on dvb-pll.
Acked-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Since we're using dvb_pll_attach now, we dont have to populate
dev->core->pll_addr or dev->core->pll_desc anymore.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
