aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2006-05-23ixgb: fix flow controlAuke Kok
Make default flow control only have *sending* of flow control packets enabled, and fix to disable / enable flow control correctly. Set flow control defaults to disable receiving flow control from the link partner, to fix the transmit fifo overlow errata Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: John Ronciak <john.ronciak@intel.com>
2006-05-23ixgb: remove duplicate code setting duplex and speedAuke Kok
Removed duplicate code. Create ixgb_set_speed_duplex function to contain duplicate code. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: John Ronciak <john.ronciak@intel.com>
2006-05-23ixgb: fix rare early tso completionAuke Kok
Fix rare early completion when using TSO. This essentially is the e1000 fix, with code that was mostly already written. Another skb frag was also needed. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: John Ronciak <john.ronciak@intel.com>
2006-05-20Merge branch 'upstream-fixes' into upstreamJeff Garzik
2006-05-20[PATCH] winbond-840-remove-badness-in-pci_map_singleErling A. Jacobsen
Call pci_map_single() with the actual size of the receive buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()). Signed-off-by: Erling A. Jacobsen <linuxcub@email.dk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] network: axnet_cs: bug fix multicast code (support older ax88190 ↵Komuro
chipset) Dear Jeff axnet_cs: bug fix multicast code (support older ax88190 chipset) Signed-off-by: komurojun-mbn@nifty.com Best Regards Komuro Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] skge: don't allow transmit ring to be too smallStephen Hemminger
The driver will get stuck (permanent transmit timeout), if the transmit ring size is set too small. It needs to have enough ring elements to hold one maximum size transmit. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] skge: bad checksums on big-endian platformsStephen Hemminger
Skge driver always causes bad checksums on big-endian. The checksum in the receive control block was being swapped when it doesn't need to be. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20Merge branch 'upstream-fixes' of ↵Jeff Garzik
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
2006-05-20[PATCH] sky2 version 1.4Stephen Hemminger
Need to track impact of this group of changes. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] sky2: force NAPI repoll if busyStephen Hemminger
If the status ring processing can't keep up with the incoming frames, it is more efficient to have NAPI keep scheduling the poll routine rather than causing another interrupt. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] sky2: more fixes for Yukon UltraStephen Hemminger
Logic error in the phy initialization code. Also, turn on wake on lan bit in status control. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] Subjec: sky2, skge: correct PCI id for DGE-560TStephen Hemminger
The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and the DGE-530T uses Yukon1 so it uses skge driver. Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544 Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] sky2: allow dual port usageStephen Hemminger
If both ports are receiving on the SysKonnect dual port cards, then it appears the bus interface unit can give an interrupt status for frame before DMA has completed. This leads to bogus frames and general confusion. This is why receive checksumming is also messed up on dual port cards. A workaround for the out of order receive problem is to eliminating split transactions on PCI-X. This version is based of the current linux-2.6.git including earlier patch to disable dual ports. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] via-rhine: revert "change mdelay to msleep and remove from ISR path"John W. Linville
Revert previous patch with subject "change mdelay to msleep and remove from ISR path". This patch seems to have caused bigger problems than it solved, and it didn't solve much of a problem to begin with... Discussion about backing-out this patch can be found here: http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2 The git commit associated w/ the original patch is: 6ba98d311d0a4ff7dc36d8f435ce60174f4c30ec Signed-off-by: John W. Linville <linville@tuxdriver.com Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] revert "forcedeth: fix multi irq issues"Andrew Morton
Revert ebf34c9b6fcd22338ef764b039b3ac55ed0e297b. Maybe. Due to crashes at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568. Cc: Ayaz Abdulla <aabdulla@nvidia.com> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20Merge branch 'master' into upstreamJeff Garzik
2006-05-19Merge branch 'for-linus' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: IB/mthca: Fix posting lists of 256 receive requests for Tavor IB/uverbs: Don't leak ref to mm on error path IB/srp: Complete correct SCSI commands on device reset IB/srp: Get rid of extra scsi_host_put()s if reconnection fails IB/srp: Don't wait for disconnection if sending DREQ fails IB/mthca: Make fw_cmd_doorbell default to 0
2006-05-19Merge master.kernel.org:/home/rmk/linux-2.6-mmcLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-mmc: [ARM] 3531/1: i.MX/MX1 SD/MMC ensure, that clock are stopped before new command and cleanups
2006-05-19Merge master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdogLinus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: [WATCHDOG] s3c2410_wdt.c stop watchdog after boot [WATCHDOG] i8xx_tco.c - remove support for ICH6 + ICH7 [WATCHDOG] Documentation/watchdog/watchdog-api.txt - fix watchdog daemon [WATCHDOG] sc1200wdt.c printk fix
2006-05-19[ARM] 3531/1: i.MX/MX1 SD/MMC ensure, that clock are stopped before new ↵Pavel Pisa
command and cleanups Patch from Pavel Pisa There has been problems that for some paths that clock are not stopped during new command programming and initiation. Result is issuing of incorrect command to the card. Some other problems are cleaned too. Noisy report of known ERRATUM #4 has been suppressed. Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-18IB/mthca: Fix posting lists of 256 receive requests for TavorMichael S. Tsirkin
If we post a list of length 256 exactly, nreq in doorbell gets set to 256 which is wrong: it should be encoded by 0. This is because we only zero it out on the next WR, which may not be there. The solution is to ring the doorbell after posting a WQE, not before posting the next one. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17IB/uverbs: Don't leak ref to mm on error pathRoland Dreier
In ib_umem_release_on_close(), if the kmalloc() fails, then a reference to current->mm will be leaked. Fix this by adding a mmput() instead of just returning on kmalloc() failure. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17[PATCH] ohci1394, sbp2: fix "scsi_add_device failed" with PL-3507 based devicesStefan Richter
Re-enable posted writes for status FIFO. Besides bringing back a very minor bandwidth tweak from Linux 2.6.15.x and older, this also fixes an interoperability regression since 2.6.16: http://bugzilla.kernel.org/show_bug.cgi?id=6356 (sbp2: scsi_add_device failed. IEEE1394 HD is not working anymore.) Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Tested-by: Vanei Heidemann <linux@javanei.com.br> Tested-by: Martin Putzlocher <mputzi@gmx.de> (chip type unconfirmed) Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-17[PATCH] sbp2: add ability to override hardwired blacklistStefan Richter
In case the blacklist with workarounds for device bugs yields a false positive, the module load parameter can now also be used as an override instead of an addition to the blacklist. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-17[PATCH] sbp2: add read_capacity workaround for iPodStefan Richter
Apple decided to copy some USB stupidity over to FireWire. The sector number returned by iPods from read_capacity is one too many. This may cause I/O errors, especially if the kernel is configured for EFI partition support. We use the same workaround as usb-storage but have to check for different model IDs. http://marc.theaimsgroup.com/?t=114233262300001 https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=187409 Acknowledgements: Diagnosis and therapy by Mathieu Chouquet-Stringer <ml2news@free.fr>, additional data about affected and unaffected Apple hardware from Vladimir Kotal, Sander De Graaf, Bryan Olmstead and Hugh Dixon. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-17[PATCH] sbp2: consolidate workaroundsStefan Richter
Grand unification of the three types of workarounds we have so far. The "skip mode page 8" workaround is now limited to devices which pretend to be of TYPE_DISK instead of TYPE_RBC. This workaround is no longer enabled for Initio bridges. Patch update in anticipation of more workarounds: - Add module parameter "workarounds". - Deprecate parameter "force_inquiry_hack". - Compose the blacklist of a compound type for better readability and extensibility. - Remove a now unused #define. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6: sky2: prevent dual port receiver problems x86_64: Check for bad dma address in b44 1GB DMA workaround The ixp2000 driver for the enp2611 was developed on a board with
2006-05-17[PATCH] bcm43xx: associate on 'ifconfig up'David Woodhouse
I still need this hack to work around the fact that softmac doesn't attempt to associate when we bring the device up... Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2006-05-17IB/srp: Complete correct SCSI commands on device resetIshai Rabinovitz
When flushing out queued commands after a successful device reset, make sure that SRP completes the right commands, instead of calling scsi_done on the command passed into the device reset handler over and over. Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17IB/srp: Get rid of extra scsi_host_put()s if reconnection failsRoland Dreier
If a reconnection attempt fails, then SRP does two scsi_host_put()s. This is a historical relic from an earlier version of the driver that took a reference on the scsi_host before trying to reconnect, so get rid of the extra scsi_host_put(). Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17IB/srp: Don't wait for disconnection if sending DREQ failsRoland Dreier
Sending a DREQ may fail, for example because the remote target has already broken the connection. If so, then SRP should not wait for the disconnection to complete, because it never will. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17IB/mthca: Make fw_cmd_doorbell default to 0Roland Dreier
Setting fw_cmd_doorbell allows FW command to be queued using posted writes instead of requiring polling on a "go" bit, so it should be a performance boost. However, the option causes problems with at least some device/firmware combinations, so set the default to 0 until we understand what's going on better. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-16Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/spi-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/spi-2.6: [PATCH] SPI: spi_bitbang: clocking fixes [PATCH] spi: Update to PXA2xx SPI Driver [PATCH] SPI: busnum == 0 needs to work [PATCH] SPI: devices can require LSB-first encodings [PATCH] SPI: Renamed bitbang_transfer_setup to spi_bitbang_setup_transfer and export it [PATCH] SPI: Add David as the SPI subsystem maintainer [PATCH] SPI: spi bounce buffer has a minimum length [PATCH] SPI: spi whitespace fixes [PATCH] SPI: add PXA2xx SSP SPI Driver [PATCH] SPI: per-transfer overrides for wordsize and clocking
2006-05-16Merge master.kernel.org:/home/rmk/linux-2.6-serialLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-serial: [ARM] 3523/1: Serial core pm_state
2006-05-16[PATCH] SPI: spi_bitbang: clocking fixesDavid Brownell
This fixes two problems triggered by the MMC stack updating clocks: - SPI masters driver should accept a max clock speed of zero; that's one convention for marking idle devices. (Presumably that helps controllers that don't autogate clocks to "off" when not in use.) - There are more than 1000 nanoseconds per millisecond; setting the clock down to 125 KHz now works properly. Showing once again that Zero (http://en.wikipedia.org/wiki/Zero) is still an inexhaustible number of bugs. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] spi: Update to PXA2xx SPI DriverStephen Street
Fix two outstanding issues with the pxa2xx_spi driver: 1) Bad cast in the function u32_writer. Thanks to Henrik Bechmann 2) Adds support for per transfer changes to speed and bits per word Signed-off-by: Stephen Street <stephen@streetfiresound.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] SPI: busnum == 0 needs to workDavid Brownell
We need to be able to have a "SPI bus 0" matching chip numbering; but that number was wrongly used to flag dynamic allocation of a bus number. This patch resolves that issue; now negative numbers trigger dynamic alloc. It also updates the how-to-write-a-controller-driver overview to mention this stuff. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] SPI: devices can require LSB-first encodingsDavid Brownell
Add spi_device hook for LSB-first word encoding, and update all the (in-tree) controller drivers to reject such devices. Eventually, some controller drivers will be updated to support lsb-first encodings on the wire; no current drivers need this. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] SPI: Renamed bitbang_transfer_setup to spi_bitbang_setup_transfer ↵Kumar Gala
and export it Renamed bitbang_transfer_setup to follow convention of other exported symbols from spi-bitbang. Exported spi_bitbang_setup_transfer to allow users of spi-bitbang to use the function in their own setup_transfer. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] SPI: spi bounce buffer has a minimum lengthDavid Brownell
Make sure that spi_write_then_read() can always handle at least 32 bytes of transfer (total, both directions), minimizing one portability issue. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] SPI: add PXA2xx SSP SPI DriverStephen Street
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master controller (see Documentation/spi/spi_summary). The driver has the following features: - Support for any PXA2xx SSP - SSP PIO and SSP DMA data transfers. - External and Internal (SSPFRM) chip selects. - Per slave device (chip) configuration. - Full suspend, freeze, resume support. Signed-off-by: Stephen Street <stephen@streetfiresound.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] SPI: per-transfer overrides for wordsize and clockingImre Deak
Some protocols (like one for some bitmap displays) require different clock speed or word size settings for each transfer in an SPI message. This adds those parameters to struct spi_transfer. They are to be used when they are nonzero; otherwise the defaults from spi_device are to be used. The patch also adds a setup_transfer callback to spi_bitbang, uses it for messages that use those overrides, and implements it so that the pure bitbanging code can help resolve any questions about how it should work. Signed-off-by: Imre Deak <imre.deak@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-16[PATCH] x86_64: Check for bad dma address in b44 1GB DMA workaroundAndi Kleen
Needed for interaction with the nommu code in x86-64 which will return bad_dma_address if the address exceeds dma_mask. Cc: netdev@vger.kernel.org Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-16[ARM] 3523/1: Serial core pm_stateAndrew Victor
Patch from Andrew Victor The serial_core already manages the power state of the UARTs, and therefore it shouldn't suspend a UART which was previously suspended. This patch modifies serial_core only call the UART-specific power-management function if the PM state is actually changing. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-15[WATCHDOG] s3c2410_wdt.c stop watchdog after bootBen Dooks
If the s3c2410 watchdog timer is not enabled by the driver at startup, ensure that it is stopped in-case the boot process has enabled it. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@osdl.org>
2006-05-15[WATCHDOG] i8xx_tco.c - remove support for ICH6 + ICH7Wim Van Sebroeck
Temporary remove support for ICH6 + ICH7. In these newer TCO's the watchdog timer has changed: the TCO_TMR register is not at the TCOBASE+0x1 offset, but changed it's place to TCOBASE+0x12 and became 10 bit long [0:9]. (Kernel BUG 6031). ICH6 + ICH7 support will be added in a new driver. Code is under test. Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@osdl.org>
2006-05-15[WATCHDOG] sc1200wdt.c printk fixDave Jones
Fix printk output. sc1200wdt: build 20020303<3>sc1200wdt: io parameter must be specified Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@osdl.org>
2006-05-15sky2: prevent dual port receiver problemsStephen Hemminger
When both ports are receiving simultaneously, the receive logic gets confused and may pass up a packet before it is full. This causes hangs, and IP will see lots of garbage packets. There is even the potential for data corruption if a later arriving packet DMA's into freed memory. It looks like a hardware bug because status arrives for a packet but no data is there. Until this bug is worked out, block the user from bringing up both ports at once. Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-15x86_64: Check for bad dma address in b44 1GB DMA workaroundAndi Kleen
Needed for interaction with the nommu code in x86-64 which will return bad_dma_address if the address exceeds dma_mask. Cc: netdev@vger.kernel.org Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-14 18:09:18 +0000